This was overlooked in commit 473b93287, which introduced DROP ACCESS
METHOD. Although that command is restricted to superusers, we don't want
even superusers dropping the built-in methods; "DROP ACCESS METHOD btree"
in particular is unrecoverable from. Pin these objects in the same way
that other initdb-created objects are pinned.
I chose to bump catversion for this fix. That's not absolutely necessary
perhaps, but it will ensure that no 9.6 production systems are missing
the pin entries.
Use disallowed instead of reserved, cannot instead of can not, and
double quotes instead of single quotes.
Also add a test to cover the bug which started this discussion.
Per discussion with Tom.
Create a "bsd" auth method that works the same as "password" so far as
clients are concerned, but calls the BSD Authentication service to
check the password. This is currently only available on OpenBSD.
Marisa Emerson, reviewed by Thomas Munro
Now that all of the infrastructure exists, add in the ability to
dump out the ACLs of the objects inside of pg_catalog or the ACLs
for objects which are members of extensions, but only if they have
been changed from their original values.
The original values are tracked in pg_init_privs. When pg_dump'ing
9.6-and-above databases, we will dump out the ACLs for all objects
in pg_catalog and the ACLs for all extension members, where the ACL
has been changed from the original value which was set during either
initdb or CREATE EXTENSION.
This should not change dumps against pre-9.6 databases.
Reviews by Alexander Korotkov, Jose Luis Tallon
This new catalog holds the privileges which the system was
initialized with at initdb time, along with any permissions set
by extensions at CREATE EXTENSION time. This allows pg_dump
(and any other similar use-cases) to detect when the privileges
set on initdb-created or extension-created objects have been
changed from what they were set to at initdb/extension-creation
time and handle those changes appropriately.
Reviews by Alexander Korotkov, Jose Luis Tallon
This brings us a bit closer to matching upstream, but since it affects
files outside src/timezone/, we might choose not to back-patch it.
Hence keep it separate from the main update patch.
Turns out the only reason initdb -X worked is that pg_mkdir_p won't
whine if you point it at something that's a symlink to a directory.
Otherwise, the attempt to create pg_xlog/ just like all the other
subdirectories would have failed. Let's be a little more explicit
about what's happening. Oversight in my patch for bug #13853
(mea culpa for not testing -X ...)
When we're creating subdirectories of PGDATA during initdb, we know darn
well that the parent directory exists (or should exist) and that the new
subdirectory doesn't (or shouldn't). There is therefore no need to use
anything more complicated than mkdir(). Using pg_mkdir_p() just opens us
up to unexpected failure modes, such as the one exhibited in bug #13853
from Nuri Boardman. It's not very clear why pg_mkdir_p() went wrong there,
but it is clear that we didn't need to be trying to create parent
directories in the first place. We're not even saving any code, as proven
by the fact that this patch nets out at minus five lines.
Since this is a response to a field bug report, back-patch to all branches.
Although these temp tables will get removed from template1 at the end of
the standalone-backend run, that's too late to keep them from getting
copied into the template0 and postgres databases, now that we use only a
single backend run for the whole sequence. While no real harm is done
by the extra copies (since they'd be deleted on first use of the temp
schema), it's still unsightly, and it would mean some wasted cycles for
every database creation for the life of the installation.
Oversight in commit c4a8812cf6. Noticed by Amit Langote.
Commit ed7b3b3811 purported to remove initdb's use of VACUUM FULL,
as had been agreed to in a pghackers discussion back in Dec 2014.
But it missed this one ...
Previously, each subroutine in initdb fired up its own standalone backend
session. Over time we'd grown as many as fifteen of these sessions,
and the cumulative startup and shutdown work for them was getting pretty
noticeable. Combining things so that all these steps share a single
backend session cuts a good 10% off the total runtime of initdb, more
if you're not fsync'ing.
The main stumbling block to doing this before was that some of the sessions
were run with -j and some not. The improved definition of -j mode
implemented by my previous commit makes it possible to fix that by running
all the post-bootstrap steps with -j; we just have to use double instead of
single newlines to end command strings. (This is only absolutely necessary
around the VACUUM and CREATE DATABASE steps, since those can't be run in a
transaction block. But it seems best to make them all use double newlines
so that the commands remain separate for error-reporting purposes.)
A minor disadvantage is that since initdb can't tell how much of its
output the backend has executed, we can no longer have the per-step
progress reporting initdb used to print. But things are fast enough
nowadays that that's not really all that useful anyway.
In passing, add more const decoration to some of the static arrays in
initdb.c.
The original code was a bit clunky; make it more amenable for further
reuse by creating a new Perl package PostgresNode, which is an
object-oriented representation of a single server, with some support
routines such as init, start, stop, psql. This serves as a better basis
on which to build further test code, and enables writing tests that use
more than one server without too much complication.
This commit modifies a lot of the existing test files, mostly to remove
explicit calls to system commands (pg_ctl) replacing them with method
calls of a PostgresNode object. The result is quite a bit more
straightforward.
Also move some initialization code to BEGIN and INIT blocks instead of
having it straight in as top-level code.
This commit also introduces package RecursiveCopy so that we can copy
whole directories without having to depend on packages that may not be
present on vanilla Perl 5.8 installations.
I also ran perltidy on the modified files, which changes some code sites
that are not otherwise touched by this patch. I tried to avoid this,
but it ended up being more trouble than it's worth.
Authors: Michael Paquier, Álvaro Herrera
Review: Noah Misch
The fsync code from the backend essentially assumes that somebody's already
validated PGDATA, at least to the extent of it being a readable directory.
That's safe enough for initdb's normal code path too, but "initdb -S"
doesn't have any other processing at all that touches the target directory.
To have reasonable error-case behavior, add a pg_check_dir call.
Per gripe from Peter E.
The argument that this is a sufficiently-expected case to be silently
ignored seems pretty thin. Andres had brought it up back when we were
still considering that most fsync failures should be hard errors, and it
probably would be legit not to fail hard for ETXTBSY --- but the same is
true for EROFS and other cases, which is why we gave up on hard failures.
ETXTBSY is surely not a normal case, so logging the failure seems fine
from here.
Make initdb's version of this logic look as much like the backend's
as possible. This is much less critical than in the backend since not
so many people use "initdb -S", but we want the same corner-case error
handling in both cases.
Back-patch to 9.3 where initdb -S option was introduced. Before that,
initdb only had to deal with freshly-created data directories, wherein
no failures should be expected.
Abhijit Menon-Sen
This eliminates many seconds of test duration and the cause to invoke
"rm -rf", which is typically unavailable on Windows.
Michael Paquier and Noah Misch
Commit c67a86f7da caught most of these,
but this negative test escaped notice. The test did pass, for the wrong
reason, under affected configurations.
Michael Paquier
The "check" target no longer needs to depend on "all", because it now
runs "install" directly, which in turn depends on "all". Doing both
will cause problems with parallel make, because two builds will run next
to each other.
Also remove the redirection of the temp-install output into a log file.
This was appropriate when this was done from within pg_regress, but now
it's just a regular make run, and especially with the above changes this
will now take the place of running the "all" target before the test
suites.
problem report by Jeff Janes, patch in part by Michael Paquier
Some of the TAP tests were supposing that PG programs would accept switches
after non-switch arguments on their command lines. While GNU getopt_long()
does allow that, our own implementation does not, and it's nowhere
suggested in our documentation that such cases should work. Adjust the
tests to use only the documented syntax.
Back-patch to 9.4, since without this the TAP tests fail when run with
src/port's getopt_long() implementation.
Michael Paquier
As with initdb these programs need to run with a restricted token, and
if they don't pg_upgrade will fail when run as a user with Adminstrator
privileges.
Backpatch to all live branches. On the development branch the code is
reorganized so that the restricted token code is now in a single
location. On the stable bramches a less invasive change is made by
simply copying the relevant code to pg_upgrade.c and pg_resetxlog.c.
Patches and bug report from Muhammad Asif Naeem, reviewed by Michael
Paquier, slightly edited by me.
strncpy() has a well-deserved reputation for being unsafe, so make an
effort to get rid of nearly all occurrences in HEAD.
A large fraction of the remaining uses were passing length less than or
equal to the known strlen() of the source, in which case no null-padding
can occur and the behavior is equivalent to memcpy(), though doubtless
slower and certainly harder to reason about. So just use memcpy() in
these cases.
In other cases, use either StrNCpy() or strlcpy() as appropriate (depending
on whether padding to the full length of the destination buffer seems
useful).
I left a few strncpy() calls alone in the src/timezone/ code, to keep it
in sync with upstream (the IANA tzcode distribution). There are also a
few such calls in ecpg that could possibly do with more analysis.
AFAICT, none of these changes are more than cosmetic, except for the four
occurrences in fe-secure-openssl.c, which are in fact buggy: an overlength
source leads to a non-null-terminated destination buffer and ensuing
misbehavior. These don't seem like security issues, first because no stack
clobber is possible and second because if your values of sslcert etc are
coming from untrusted sources then you've got problems way worse than this.
Still, it's undesirable to have unpredictable behavior for overlength
inputs, so back-patch those four changes to all active branches.
Used to say just "could not read password from file "...": Success", which
isn't very informative.
Mats Erik Andersson. Backpatch to all supported versions.
Since this is not something that a user should change,
pg_config_manual.h was an inappropriate place for it.
In initdb.c, remove the use of the macro, because utils/guc.h can't be
included by non-backend code. But we hardcode all the other
configuration file names there, so this isn't a disaster.
Transactions can now set their commit timestamp directly as they commit,
or an external transaction commit timestamp can be fed from an outside
system using the new function TransactionTreeSetCommitTsData(). This
data is crash-safe, and truncated at Xid freeze point, same as pg_clog.
This module is disabled by default because it causes a performance hit,
but can be enabled in postgresql.conf requiring only a server restart.
A new test in src/test/modules is included.
Catalog version bumped due to the new subdirectory within PGDATA and a
couple of new SQL functions.
Authors: Álvaro Herrera and Petr Jelínek
Reviewed to varying degrees by Michael Paquier, Andres Freund, Robert
Haas, Amit Kapila, Fujii Masao, Jaime Casanova, Simon Riggs, Steven
Singer, Peter Eisentraut
630cd14426 added initdb --sync-only, for use by pg_upgrade, by just
exposing the existing fsync code. That's wrong, because initdb so far
had absolutely no reason to deal with tablespaces.
Fix --sync-only by additionally explicitly syncing each of the
tablespaces.
Backpatch to 9.3 where --sync-only was introduced.
Abhijit Menon-Sen and Andres Freund
The old name wasn't very descriptive as of actual contents of the
directory, which are historical snapshots in the snapshots/
subdirectory and mappingdata for rewritten tuples in
mappings/. There's been a fair amount of discussion what would be a
good name. I'm settling for pg_logical because it's likely that
further data around logical decoding and replication will need saving
in the future.
Also add the missing entry for the directory into storage.sgml's list
of PGDATA contents.
Bumps catversion as the data directories won't be compatible.
Historically these database properties could be manipulated only by
manually updating pg_database, which is error-prone and only possible for
superusers. But there seems no good reason not to allow database owners to
set them for their databases, so invent CREATE/ALTER DATABASE options to do
that. Adjust a couple of places that were doing it the hard way to use the
commands instead.
Vik Fearing, reviewed by Pavel Stehule
In yesterday's commit 2dc4f011fd, I tried
to force buffering of stdout/stderr in initdb to be what it is by
default when the program is run interactively on Unix (since that's how
most manual testing is done). This tripped over the fact that Windows
doesn't support _IOLBF mode. We dealt with that a long time ago in
syslogger.c by falling back to unbuffered mode on Windows. Export that
solution in port.h and use it in initdb.
Back-patch to 8.4, like the previous commit.
Peter Eisentraut
Tom Lane
Stephen Frost
Bruce Momjian
Alvaro Herrera
Noah Misch
Andrew Dunstan
Heikki Linnakangas
Andres Freund