Regexps like "(.){0}...\1" drew an "invalid backreference number".
That's not unreasonable on its face, since the capture group will
never be matched if it's iterated zero times. However, other engines
such as Perl's don't complain about this, nor do we throw an error for
related cases such as "(.)|\1", even though that backref can never
succeed either. Also, if the zero-iterations case happens at runtime
rather than compile time --- say, "(x)*...\1" when there's no "x" to
be found --- that's not an error, we just deem the backref to not
match. Making this even less defensible, no error was thrown for
nested cases such as "((.)){0}...\2"; and to add insult to injury,
those cases could result in assertion failures instead. (It seems
that nothing especially bad happened in non-assert builds, though.)
Let's just fix it so that no error is thrown and instead the backref
is deemed to never match, so that compile-time detection of no
iterations behaves the same as run-time detection.
Per report from Mark Dilger. This appears to be an aboriginal error
in Spencer's library, so back-patch to all supported versions.
Pre-v14, it turns out to also be necessary to back-patch one aspect of
commits cb76fbd7e/00116dee5, namely to create capture-node subREs with
the begin/end states of their subexpressions, not the current lp/rp
of the outer parseqatom invocation. Otherwise delsub complains that
we're trying to disconnect a state from itself. This is a bit scary
but code examination shows that it's safe: in the pre-v14 code, if we
want to wrap iteration around the subexpression, the first thing we do
is overwrite the atom's begin/end fields with new states. So the
bogus values didn't survive long enough to be used for anything, except
if no iteration is required, in which case it doesn't matter.
Discussion: https://postgr.es/m/A099E4A8-4377-4C64-A98C-3DEDDC075502@enterprisedb.com
The current refresh behavior tries to just refresh added/dropped
publications but that leads to removing wrong tables from subscription. We
can't refresh just the dropped publication because it is quite possible
that some of the tables are removed from publication by that time and now
those will remain as part of the subscription. Also, there is a chance
that the tables that were part of the publication being dropped are also
part of another publication, so we can't remove those.
So, we decided that by default, add/drop commands will also act like
REFRESH PUBLICATION which means they will refresh all the publications. We
can keep the old behavior for "add publication" but it is better to be
consistent with "drop publication".
Author: Hou Zhijie
Reviewed-by: Masahiko Sawada, Amit Kapila
Backpatch-through: 14, where it was introduced
Discussion: https://postgr.es/m/OS0PR01MB5716935D4C2CC85A6143073F94EF9@OS0PR01MB5716.jpnprd01.prod.outlook.com
The recursion in cdissect() was careless about clearing match data
for capturing parentheses after rejecting a partial match. This
could allow a later back-reference to succeed when by rights it
should fail for lack of a defined referent.
To fix, think a little more rigorously about what the contract
between different levels of cdissect's recursion needs to be.
With the right spec, we can fix this using fewer rather than more
resets of the match data; the key decision being that a failed
sub-match is now explicitly responsible for clearing any matches
it may have set.
There are enough other cross-checks and optimizations in the code
that it's not especially easy to exhibit this problem; usually, the
match will fail as-expected. Plus, regexps that are even potentially
vulnerable are most likely user errors, since there's just not much
point in writing a back-ref that doesn't always have a referent.
These facts perhaps explain why the issue hasn't been detected,
even though it's almost certainly a couple of decades old.
Discussion: https://postgr.es/m/151435.1629733387@sss.pgh.pa.us
We've supported parallel aggregation since e06a38965. At the time, we
didn't quite get around to also adding parallel DISTINCT. So, let's do
that now.
This is implemented by introducing a two-phase DISTINCT. Phase 1 is
performed on parallel workers, rows are made distinct there either by
hashing or by sort/unique. The results from the parallel workers are
combined and the final distinct phase is performed serially to get rid of
any duplicate rows that appear due to combining rows for each of the
parallel workers.
Author: David Rowley
Reviewed-by: Zhihong Yu
Discussion: https://postgr.es/m/CAApHDvrjRxVKwQN0he79xS+9wyotFXL=RmoWqGGO2N45Farpgw@mail.gmail.com
transformLockingClause neglected to exclude the pseudo-RTEs for
OLD/NEW when processing a rule's query. This led to odd errors
or even crashes later on. This bug is very ancient, but it's
not terribly surprising that nobody noticed, since the use-case
for SELECT FOR UPDATE in a non-view rule is somewhere between
thin and non-existent. Still, crashing is not OK.
Per bug #17151 from Zhiyong Wu. Thanks to Masahiko Sawada
for analysis of the problem.
Discussion: https://postgr.es/m/17151-c03a3e6e4ec9aadb@postgresql.org
Recursion into the FILTER clause was mis-implemented, such that a
relevant Var or Aggref at the very top of the FILTER clause would
be ignored. (Of course, that'd have to be a plain boolean Var or
boolean-returning aggregate.) The consequence would be
mis-identification of the correct semantic level of the aggregate,
which could lead to not-per-spec query behavior. If the FILTER
expression is an aggregate, this could also lead to failure to issue
an expected "aggregate function calls cannot be nested" error, which
would likely result in a core dump later on, since the planner and
executor aren't expecting such cases to appear.
The root cause is that commit b560ec1b0 blindly copied some code
that assumed it's recursing into a List, and thus didn't examine the
top-level node. To forestall questions about why this call doesn't
look like the others, as well as possible future copy-and-paste
mistakes, let's change all three check_agg_arguments_walker calls in
check_agg_arguments, even though only the one for the filter clause
is really broken.
Per bug #17152 from Zhiyong Wu. This has been wrong since we
implemented FILTER, so back-patch to all supported versions.
(Testing suggests that pre-v11 branches manage to avoid crashing
in the bad-Aggref case, thanks to "redundant" checks in ExecInitAgg.
But I'm not sure how thorough that protection is, and anyway the
wrong-behavior issue remains, so fix 9.6 and 10 too.)
Discussion: https://postgr.es/m/17152-c7f906cc1a88e61b@postgresql.org
I was overoptimistic to assume that UTF8-based locales would all
consider U+1500 to be a member of the [[:alpha:]] char class.
Tweak the test cases added by commit 78a843f11 to avoid that
assumption. We might need to lobotomize them further, but this
should be enough to fix the early buildfarm reports.
The functions moveins(), copyins(), moveouts(), copyouts() are
required to preserve the invariant that there are no duplicate arcs in
the regex's NFA. Spencer's original implementation of them was O(N^2)
since it checked separately for a match to each source arc. In commit
579840ca0 I improved that by adding sort/merge logic to be used if
more than a few arcs are to be moved/copied. However, I now realize
that that missed a bet. At many call sites, the target state is newly
made and cannot have any existing in-arcs (respectively out-arcs)
that could be duplicates. So spending any cycles at all on checking
for duplicates is wasted effort; in these cases we can just blindly
move/copy all the source arcs. Add code paths to do that.
It turns out that for copyins()/copyouts(), *all* the call sites have
this property, making all the "improved" logic in them flat out
unreachable. Perhaps we'll need the full capability again someday,
so I just #ifdef'd those paths out rather than removing them entirely.
In passing, add a few test cases to improve code coverage in this
area as well as in regc_locale.c/regc_pg_locale.c.
Discussion: https://postgr.es/m/810272.1629064063@sss.pgh.pa.us
If the replacement string doesn't contain \1...\9, then we don't
need sub-match locations, so we can use the REG_NOSUB optimization
here too. There's already a pre-scan of the replacement string
to look for backslashes, so extend that to check for digits, and
refactor to allow that to happen before we compile the regexp.
While at it, try to speed up the pre-scan by using memchr() instead
of a handwritten loop. It's likely that this is lost in the noise
compared to the regexp processing proper, but maybe not. In any
case, this coding is shorter.
Also, add some test cases to improve the poor coverage of
appendStringInfoRegexpSubstr().
Discussion: https://postgr.es/m/3534632.1628536485@sss.pgh.pa.us
Identifying the precise match locations for parenthesized subexpressions
is a fairly expensive task given the way our regexp engine works, both
at regexp compile time (where we must create an optimized NFA for each
parenthesized subexpression) and at runtime (where determining exact
match locations requires laborious search).
Up to now we've made little attempt to optimize this situation. This
patch identifies cases where we know at compile time that we won't
need to know subexpression match locations, and teaches the regexp
compiler to not bother creating per-subexpression regexps for
parenthesis pairs that are not referenced by backrefs elsewhere in
the regexp. (To preserve semantics, we obviously still have to
pin down the match locations of backref references.) Users could
have obtained the same results before this by being careful to
write "non capturing" parentheses wherever possible, but few people
bother with that.
Discussion: https://postgr.es/m/2219936.1628115334@sss.pgh.pa.us
Commit cebc1d34e taught parseqatom() to optimize cases where a branch
contains only one, "messy", atom by getting rid of excess subRE nodes.
The way we really should do that is to keep the subRE built for the
"messy" child atom; but to avoid changing parseqatom's nominal API,
I made it delete that node after copying its fields to the outer subRE
made by parsebranch(). It seems that that actually worked at the time;
but it became dangerous after ea1268f63, because that later commit
allowed the lower invocation of parse() to return a subRE that was also
pointed to by some v->subs[] entry. This meant we could wind up with a
dangling pointer in v->subs[], allowing a later backref to misbehave,
but only if that subRE struct had been reused in between. So the damage
seems confined to cases like '((...))...(...\2'.
To fix, do what I should have done before and modify parseqatom's API
to make it possible for it to remove the caller's subRE instead of the
callee's. That's safer because we know that subRE isn't complete yet,
so noplace else will have a pointer to it.
Per report from Mark Dilger. Back-patch to v14 where the problematic
patches came in.
Discussion: https://postgr.es/m/0203588E-E609-43AF-9F4F-902854231EE7@enterprisedb.com
Rather than trying to pick table aliases that won't conflict with
any possible user-defined matview column name, adjust the queries'
syntax so that the aliases are only used in places where they can't be
mistaken for column names. Mostly this consists of writing "alias.*"
not just "alias", which adds clarity for humans as well as machines.
We do have the issue that "SELECT alias.*" acts differently from
"SELECT alias", but we can use the same hack ruleutils.c uses for
whole-row variables in SELECT lists: write "alias.*::compositetype".
We might as well revert to the original aliases after doing this;
they're a bit easier to read.
Like 75d66d10e, back-patch to all supported branches.
Discussion: https://postgr.es/m/2488325.1628261320@sss.pgh.pa.us
Casting a value that's already of a type with a specific typmod
to an unspecified typmod doesn't do anything so far as run-time
behavior is concerned. However, it really ought to change the
exposed type of the expression to match. Up to now,
coerce_type_typmod hasn't bothered with that, which creates gotchas
in contexts such as recursive unions. If for example one side of
the union is numeric(18,3), but it needs to be plain numeric to
match the other side, there's no direct way to express that.
This is easy enough to fix, by inserting a RelabelType to update the
exposed type of the expression. However, it's a bit nervous-making
to change this behavior, because it's stood for a really long time.
(I strongly suspect that it's like this in part because the logic
pre-dates the introduction of RelabelType in 7.0. The commit log
message for 57b30e8e2 is interesting reading here.) As a compromise,
we'll sneak the change into 14beta3, and consider back-patching to
stable branches if no complaints emerge in the next three months.
Discussion: https://postgr.es/m/CABNQVagu3bZGqiTjb31a8D5Od3fUMs7Oh3gmZMQZVHZ=uWWWfQ@mail.gmail.com
Formerly, the numeric code tested whether an integer value of a larger
type would fit in a smaller type by casting it to the smaller type and
then testing if the reverse conversion produced the original value.
That's perfectly fine, except that it caused a test failure on
buildfarm animal castoroides, most likely due to a compiler bug.
Instead, do these tests by comparing against PG_INT16/32_MIN/MAX. That
matches existing code in other places, such as int84(), which is more
widely tested, and so is less likely to go wrong.
While at it, add regression tests covering the numeric-to-int8/4/2
conversions, and adjust the recently added tests to the style of
434ddfb79a (on the v11 branch) to make failures easier to diagnose.
Per buildfarm via Tom Lane, reviewed by Tom Lane.
Discussion: https://postgr.es/m/2394813.1628179479%40sss.pgh.pa.us
This fixes a long-standing bug when using to_char() to format a
numeric value in scientific notation -- if the value's exponent is
less than -NUMERIC_MAX_DISPLAY_SCALE-1 (-1001), it produced a
division-by-zero error.
The reason for this error was that get_str_from_var_sci() divides its
input by 10^exp, which it produced using power_var_int(). However, the
underflow test in power_var_int() causes it to return zero if the
result scale is too small. That's not a problem for power_var_int()'s
only other caller, power_var(), since that limits the rscale to 1000,
but in get_str_from_var_sci() the exponent can be much smaller,
requiring a much larger rscale. Fix by introducing a new function to
compute 10^exp directly, with no rscale limit. This also allows 10^exp
to be computed more efficiently, without any numeric multiplication,
division or rounding.
Discussion: https://postgr.es/m/CAEZATCWhojfH4whaqgUKBe8D5jNHB8ytzemL-PnRx+KCTyMXmg@mail.gmail.com
Commit a8fd13cab0 added support for prepared transactions to built-in
logical replication via a new option "two_phase" for a subscription. The
"two_phase" option was not allowed with the existing streaming option.
This commit permits the combination of "streaming" and "two_phase"
subscription options. It extends the pgoutput plugin and the subscriber
side code to add the prepare API for streaming transactions which will
apply the changes accumulated in the spool-file at prepare time.
Author: Peter Smith and Ajin Cherian
Reviewed-by: Vignesh C, Amit Kapila, Greg Nancarrow
Tested-By: Haiying Tang
Discussion: https://postgr.es/m/02DA5F5E-CECE-4D9C-8B4B-418077E2C010@postgrespro.ru
Discussion: https://postgr.es/m/CAMGcDxeqEpWj3fTXwqhSwBdXd2RS9jzwWscO-XbeCfso6ts3+Q@mail.gmail.com
This patch adds new functions regexp_count(), regexp_instr(),
regexp_like(), and regexp_substr(), and extends regexp_replace()
with some new optional arguments. All these functions follow
the definitions used in Oracle, although there are small differences
in the regexp language due to using our own regexp engine -- most
notably, that the default newline-matching behavior is different.
Similar functions appear in DB2 and elsewhere, too. Aside from
easing portability, these functions are easier to use for certain
tasks than our existing regexp_match[es] functions.
Gilles Darold, heavily revised by me
Discussion: https://postgr.es/m/fc160ee0-c843-b024-29bb-97b5da61971f@darold.net
959d00e9d added the ability to make use of an Append node instead of a
MergeAppend when we wanted to perform a scan of a partitioned table and
the required sort order was the same as the partitioned keys and the
partitioned table was defined in such a way that earlier partitions were
guaranteed to only contain lower-order values than later partitions.
However, previously we didn't allow these ordered partition scans for
LIST partitioned table when there were any partitions that allowed
multiple Datums. This was a very cheap check to make and we could likely
have done a little better by checking if there were interleaved
partitions, but at the time we didn't have visibility about which
partitions were pruned, so we still may have disallowed cases where all
interleaved partitions were pruned.
Since 475dbd0b7, we now have knowledge of pruned partitions, we can do a
much better job inside partitions_are_ordered().
Here we pass which partitions survived partition pruning into
partitions_are_ordered() and, for LIST partitioning, have it check to see
if any live partitions exist that are also in the new "interleaved_parts"
field defined in PartitionBoundInfo.
For RANGE partitioning we can relax the code which caused the partitions
to be unordered if a DEFAULT partition existed. Since we now know which
partitions were pruned, partitions_are_ordered() now returns true when the
DEFAULT partition was pruned.
Reviewed-by: Amit Langote, Zhihong Yu
Discussion: https://postgr.es/m/CAApHDvrdoN_sXU52i=QDXe2k3WAo=EVry29r2+Tq2WYcn2xhEA@mail.gmail.com
The test is expecting two prepared transactions corresponding to two
subscriptions but it waits to catch up for just one subscription. Fix it
by allowing to wait for both subscriptions.
Reported-by: Michael Paquier, as per buildfarm
Author: Ajin Cherian
Reviewed-By: Amit Kapila, Vignesh C, Peter Smith
Discussion: https://postgr.es/m/CAA4eK1+_0iNQ8Z=KVTjmmAqNX-hyv+1+fnZ-Yx8CVP=uAcekqw@mail.gmail.com
This fixes a couple of related problems that arise when raising
numbers to very large powers.
Firstly, when raising a negative number to a very large integer power,
the result should be well-defined, but the previous code would only
cope if the exponent was small enough to go through power_var_int().
Otherwise it would throw an internal error, attempting to take the
logarithm of a negative number. Fix this by adding suitable handling
to the general case in power_var() to cope with negative bases,
checking for integer powers there.
Next, when raising a (positive or negative) number whose absolute
value is slightly less than 1 to a very large power, the result should
approach zero as the power is increased. However, in some cases, for
sufficiently large powers, this would lose all precision and return 1
instead of 0. This was due to the way that the local_rscale was being
calculated for the final full-precision calculation:
local_rscale = rscale + (int) val - ln_dweight + 8
The first two terms on the right hand side are meant to give the
number of significant digits required in the result ("val" being the
estimated result weight). However, this failed to account for the fact
that rscale is clipped to a maximum of NUMERIC_MAX_DISPLAY_SCALE
(1000), and the result weight might be less then -1000, causing their
sum to be negative, leading to a loss of precision. Fix this by
forcing the number of significant digits calculated to be nonnegative.
It's OK for it to be zero (when the result weight is less than -1000),
since the local_rscale value then includes a few extra digits to
ensure an accurate result.
Finally, add additional underflow checks to exp_var() and power_var(),
so that they consistently return zero for cases like this where the
result is indistinguishable from zero. Some paths through this code
already returned zero in such cases, but others were throwing overflow
errors.
Dean Rasheed, reviewed by Yugo Nagata.
Discussion: http://postgr.es/m/CAEZATCW6Dvq7+3wN3tt5jLj-FyOcUgT5xNoOqce5=6Su0bCR0w@mail.gmail.com
Buildfarm shows that this test has a further failure mode when a
checkpoint starts earlier than expected, so we detect a "checkpoint
completed" line that's not the one we want. Change the config to try
and prevent this.
Per buildfarm
While at it, update one comment that was forgotten in commit
d18e75664a.
Author: Kyotaro Horiguchi <horikyota.ntt@gmail.com>
Discussion: https://postgr.es/m/20210729.162038.534808353849568395.horikyota.ntt@gmail.com
Sometimes cygpath has been observed to return a path with a trailing
slash. That can cause problems, Also, make "cygpath" usage
consistent with "pwd -W" with respect to the use of forward slashes.
Backpatch to release 14 where the current code was introduced.
The clientside log saved from the testrun was removed in 1caef31d9
but the entry in the .gitignore file remained. While this exists
in older branches as well, it's mostly a cosmetical fix so no back-
patching is done.
Reviewed-by: Michael Paquier
Discussion: https://postgr.es/m/F8E73040-BB6F-43BF-95B4-3CEC037BE856@yesql.se
There is only one constructor now for PostgresNode, with the idiomatic
name 'new'. The method is not exported by the class, and must be called
as "PostgresNode->new('name',[args])". All the TAP tests that use
PostgresNode are modified accordingly. Third party scripts will need
adjusting, which is a fairly mechanical process (I just used a sed
script).
This method will modify or delete an existing line in the config file
rather than simply appending to the file. This makes adjustment of files
for older versions much simpler and more compact.
This is now the default for pg_ctl, but having the flag here explicitly
does no harm and helps with backwards compatibility of the PostgresNode
module.
The logic used to support a change of access method for a table is
similar to changes for tablespace or relation persistence, requiring a
table rewrite with an exclusive lock of the relation changed. Table
rewrites done in ALTER TABLE already go through the table AM layer when
scanning tuples from the old relation and inserting them into the new
one, making this implementation straight-forward.
Note that partitioned tables are not supported as these have no access
methods defined.
Author: Justin Pryzby, Jeff Davis
Reviewed-by: Michael Paquier, Vignesh C
Discussion: https://postgr.es/m/20210228222530.GD20769@telsasoft.com
We failed to deal with an UNKNOWN-type input for
anycompatiblemultirange; that should throw an error indicating
that we don't know how to resolve the multirange type.
We also failed to infer the type of an anycompatiblerange output
from an anycompatiblemultirange input or vice versa.
Per bug #17066 from Alexander Lakhin. Back-patch to v14
where multiranges were added.
Discussion: https://postgr.es/m/17066-16a37f6223a8470b@postgresql.org
Commit 48c5c9068 failed to allow for buildfarm animals that
force jit = on. I'm surprised that this hasn't come up
elsewhere in explain.sql, so turn it off for that whole
test script not just the one new test case.
Per buildfarm.
The error messages using the word "non-negative" are confusing
because it's ambiguous about whether it accepts zero or not.
This commit improves those error messages by replacing it with
less ambiguous word like "greater than zero" or
"greater than or equal to zero".
Also this commit added the note about the word "non-negative" to
the error message style guide, to help writing the new error messages.
When postgres_fdw option fetch_size was set to zero, previously
the error message "fetch_size requires a non-negative integer value"
was reported. This error message was outright buggy. Therefore
back-patch to all supported versions where such buggy error message
could be thrown.
Reported-by: Hou Zhijie
Author: Bharath Rupireddy
Reviewed-by: Kyotaro Horiguchi, Fujii Masao
Discussion: https://postgr.es/m/OS0PR01MB5716415335A06B489F1B3A8194569@OS0PR01MB5716.jpnprd01.prod.outlook.com
This patch causes EXPLAIN output to refer to objects that are in
the current session's temp schema with the "pg_temp" schema alias
rather than that schema's actual name. This is useful for our own
testing purposes since it will stabilize EXPLAIN VERBOSE output
for such cases, allowing us to use that in regression tests.
It should be less confusing for end users too.
Since ruleutils.c needs to change behavior for this, the change
also leaks into a few other users of ruleutils.c, for example
pg_get_viewdef(). AFAICS that won't cause any problems.
We did find that aggressively trying to change this behavior
across-the-board would cause issues, but as long as "pg_temp"
only appears within generated SQL text, I think it'll be fine.
Along the way, make get_namespace_name_or_temp conform to the
same API as get_namespace_name, ie that it returns a palloc'd
string or NULL. The current behavior hasn't caused any bugs
since no callers attempt to pfree the result, but if it gets
more widespread usage that could become a problem.
Amul Sul, reviewed and extended by me
Discussion: https://postgr.es/m/CAAJ_b97W=QaGmag9AhWNbmx3uEYsNkXWL+OVW1_E1D3BtgWvtw@mail.gmail.com
Commit ad600bba04 added psql command \dX listing extended statistics
objects, but it failed to consider search_path when selecting the
elements so some of the returned elements might be invisible.
The visibility was already considered for tab completion (added by
commit d99d58cdc8), so adding it to the query is fairly simple.
Reported and fix by Justin Pryzby, regression tests by me. Backpatch
to PostgreSQL 14, where \dX was introduced.
Batchpatch-through: 14
Author: Justin Pryzby
Reviewed-by: Tatsuro Yamada
Discussion: https://postgr.es/m/c027a541-5856-75a5-0868-341301e1624b%40nttcom.co.jp_1
Formerly, when specifying NUMERIC(precision, scale), the scale had to
be in the range [0, precision], which was per SQL spec. This commit
extends the range of allowed scales to [-1000, 1000], independent of
the precision (whose valid range remains [1, 1000]).
A negative scale implies rounding before the decimal point. For
example, a column might be declared with a scale of -3 to round values
to the nearest thousand. Note that the display scale remains
non-negative, so in this case the display scale will be zero, and all
digits before the decimal point will be displayed.
A scale greater than the precision supports fractional values with
zeros immediately after the decimal point.
Take the opportunity to tidy up the code that packs, unpacks and
validates the contents of a typmod integer, encapsulating it in a
small set of new inline functions.
Bump the catversion because the allowed contents of atttypmod have
changed for numeric columns. This isn't a change that requires a
re-initdb, but negative scale values in the typmod would confuse old
backends.
Dean Rasheed, with additional improvements by Tom Lane. Reviewed by
Tom Lane.
Discussion: https://postgr.es/m/CAEZATCWdNLgpKihmURF8nfofP0RFtAKJ7ktY6GcZOPnMfUoRqA@mail.gmail.com
We have an implementation restriction that PREPARE TRANSACTION can't
handle cases where both session-lifespan and transaction-lifespan locks
are held on the same lockable object. (That's because we'd otherwise
need to acquire a new PROCLOCK entry during post-prepare cleanup, which
is an operation that might fail. The situation can only arise with odd
usages of advisory locks, so removing the restriction is probably not
worth the amount of effort it would take.) AtPrepare_Locks attempted
to enforce this, but its logic was many bricks shy of a load, because
it only detected cases where the session and transaction locks had the
same lockmode. Locks of different modes on the same object would lead
to the rather unhelpful message "PANIC: we seem to have dropped a bit
somewhere".
To fix, build a transient hashtable with one entry per locktag,
not one per locktag + mode, and use that to detect conflicts.
Per bug #17122 from Alexander Pyhalov. This bug is ancient,
so back-patch to all supported branches.
Discussion: https://postgr.es/m/17122-04f3c32098a62233@postgresql.org
Animals running in Czech locale failed. I could try to find table names
that don't have this problem, but it seems simpler to just use the C
locale.
Per buildfarm
Renaming triggers on partitioned tables had two problems: first,
it did not recurse to renaming the triggers on the partitions; and
second, it failed to prohibit renaming clone triggers. Having triggers
with different names in partitions is pointless, and furthermore pg_dump
would not preserve names for partitions anyway.
Not backpatched -- making the ALTER TRIGGER throw an error in stable
versions might cause problems for existing scripts.
Co-authored-by: Arne Roland <A.Roland@index.de>
Co-authored-by: Álvaro Herrera <alvherre@alvh.no-ip.org>
Reviewed-by: Zhihong Yu <zyu@yugabyte.com>
Discussion: https://postgr.es/m/d0fd7040c2fb4de1a111b9d9ccc456b8@index.de
Follow-up to 2ed532ee8c, a few error
messages in the logical replication area currently only deal with
tables, but if we're anticipating more relkinds such as sequences
being handled, then these messages also fall into the category
affected by the previous patch, so adjust them too.
Reviewed-by: Michael Paquier <michael@paquier.xyz>
Discussion: https://www.postgresql.org/message-id/c9ba5c6a-4bd5-e12c-1b3c-edbcaedbf392@enterprisedb.com
We don't allow to create replication slot_name as an empty string ('') via
SQL API pg_create_logical_replication_slot() but it is allowed to be set
via Alter Subscription command. This will lead to apply worker repeatedly
keep trying to stream data via slot_name '' and the user is not allowed to
create the slot with that name.
Author: Japin Li
Reviewed-By: Ranier Vilela, Amit Kapila
Backpatch-through: 10, where it was introduced
Discussion: https://postgr.es/m/MEYP282MB1669CBD98E721C77CA696499B61A9@MEYP282MB1669.AUSP282.PROD.OUTLOOK.COM
It has been spotted that multiranges lack of ability to decompose them into
individual ranges. Subscription and proper expanded object representation
require substantial work, and it's too late for v14. This commit
provides the implementation of unnest(multirange), which is quite trivial.
unnest(multirange) is defined as a polymorphic procedure.
Catversion is bumped.
Reported-by: Jonathan S. Katz
Discussion: https://postgr.es/m/flat/60258efe-bd7e-4886-82e1-196e0cac5433%40postgresql.org
Author: Alexander Korotkov
Reviewed-by: Justin Pryzby, Jonathan S. Katz, Zhihong Yu, Tom Lane
Reviewed-by: Alvaro Herrera
Check for conflicting or redundant options, as we do for most other
commands. Specifying any option more than once is at best redundant,
and quite likely indicates a bug in the user's code.
While at it, improve the error for conflicting locale options by
adding detail text (the same as for CREATE DATABASE).
Bharath Rupireddy, reviewed by Vignesh C. Some additional hacking by
me.
Discussion: https://postgr.es/m/CALj2ACWtL6fTLdyF4R_YkPtf1YEDb6FUoD5DGAki3rpD+sWqiA@mail.gmail.com
The new test code added in ead9e51e82 is racy -- it hinges on
shared-memory state, which changes before the WARNING message is logged.
Put it the other way around.
Backpatch to 13.
Author: Álvaro Herrera <alvherre@alvh.no-ip.org>
Discussion: https://postgr.es/m/202107161809.zclasccpfcg3@alvherre.pgsql
pg_dump failed to preserve the 'enabled' flag (which can be not only
disabled, but also REPLICA or ALWAYS) for partitions which had it
changed from their respective parents. Attempt to handle that by
including a definition for such triggers in the dump, but replace the
standard CREATE TRIGGER line with an ALTER TRIGGER line.
Backpatch to 11, where these triggers can exist. In branches 11 and 12,
pick up a few test lines from commit b9b408c487 to verify that
pg_upgrade is okay with these arrangements.
Co-authored-by: Justin Pryzby <pryzby@telsasoft.com>
Co-authored-by: Álvaro Herrera <alvherre@alvh.no-ip.org>
Discussion: https://postgr.es/m/20200930223450.GA14848@telsasoft.com
When triggers are cloned from partitioned tables to their partitions,
the 'tgenabled' flag (origin/replica/always/disable) was not propagated.
Make it so that the flag on the trigger on partition is initially set to
the same value as on the partitioned table.
Add a test case to verify the behavior.
Backpatch to 11, where this appeared in commit 86f575948c.
Author: Álvaro Herrera <alvherre@alvh.no-ip.org>
Reported-by: Justin Pryzby <pryzby@telsasoft.com>
Discussion: https://postgr.es/m/20200930223450.GA14848@telsasoft.com
When some slots are invalidated due to the max_slot_wal_keep_size limit,
the old segment horizon should move forward to stay within the limit.
However, in commit c655077639 we forgot to call KeepLogSeg again to
recompute the horizon after invalidating replication slots. In cases
where other slots remained, the limits would be recomputed eventually
for other reasons, but if all slots were invalidated, the limits would
not move at all afterwards. Repair.
Backpatch to 13 where the feature was introduced.
Author: Kyotaro Horiguchi <horikyota.ntt@gmail.com>
Reported-by: Marcin Krupowicz <mk@071.ovh>
Discussion: https://postgr.es/m/17103-004130e8f27782c9@postgresql.org
As of v14, pg_depend contains almost 7000 "pin" entries recording
the OIDs of built-in objects. This is a fair amount of bloat for
every database, and it adds time to pg_depend lookups as well as
initdb. We can get rid of all of those entries in favor of an OID
range check, i.e. "OIDs below FirstUnpinnedObjectId are pinned".
(template1 and the public schema are exceptions. Those exceptions
are now wired into IsPinnedObject() instead of initdb's code for
filling pg_depend, but it's the same amount of cruft either way.)
The contents of pg_shdepend are modified likewise.
Discussion: https://postgr.es/m/3737988.1618451008@sss.pgh.pa.us
When reporting "conflicting or redundant options" errors, try to
ensure that errposition() is used, to help the user identify the
offending option.
Formerly, errposition() was invoked in less than 60% of cases. This
patch raises that to over 90%, but there remain a few places where the
ParseState is not readily available. Using errdetail() might improve
the error in such cases, but that is left as a task for the future.
Additionally, since this error is thrown from over 100 places in the
codebase, introduce a dedicated function to throw it, reducing code
duplication.
Extracted from a slightly larger patch by Vignesh C. Reviewed by
Bharath Rupireddy, Alvaro Herrera, Dilip Kumar, Hou Zhijie, Peter
Smith, Daniel Gustafsson, Julien Rouhaud and me.
Discussion: https://postgr.es/m/CALDaNm33FFSS5tVyvmkoK2cCMuDVxcui=gFrjti9ROfynqSAGA@mail.gmail.com
To add support for streaming transactions at prepare time into the
built-in logical replication, we need to do the following things:
* Modify the output plugin (pgoutput) to implement the new two-phase API
callbacks, by leveraging the extended replication protocol.
* Modify the replication apply worker, to properly handle two-phase
transactions by replaying them on prepare.
* Add a new SUBSCRIPTION option "two_phase" to allow users to enable
two-phase transactions. We enable the two_phase once the initial data sync
is over.
We however must explicitly disable replication of two-phase transactions
during replication slot creation, even if the plugin supports it. We
don't need to replicate the changes accumulated during this phase,
and moreover, we don't have a replication connection open so we don't know
where to send the data anyway.
The streaming option is not allowed with this new two_phase option. This
can be done as a separate patch.
We don't allow to toggle two_phase option of a subscription because it can
lead to an inconsistent replica. For the same reason, we don't allow to
refresh the publication once the two_phase is enabled for a subscription
unless copy_data option is false.
Author: Peter Smith, Ajin Cherian and Amit Kapila based on previous work by Nikhil Sontakke and Stas Kelvich
Reviewed-by: Amit Kapila, Sawada Masahiko, Vignesh C, Dilip Kumar, Takamichi Osumi, Greg Nancarrow
Tested-By: Haiying Tang
Discussion: https://postgr.es/m/02DA5F5E-CECE-4D9C-8B4B-418077E2C010@postgrespro.ru
Discussion: https://postgr.es/m/CAA4eK1+opiV4aFTmWWUF9h_32=HfPOW9vZASHarT0UA5oBrtGw@mail.gmail.com
"Result Cache" was never a great name for this node, but nobody managed
to come up with another name that anyone liked enough. That was until
David Johnston mentioned "Node Memoization", which Tom Lane revised to
just "Memoize". People seem to like "Memoize", so let's do the rename.
Reviewed-by: Justin Pryzby
Discussion: https://postgr.es/m/20210708165145.GG1176@momjian.us
Backpatch-through: 14, where Result Cache was introduced
This fixes an overflow error when using the numeric * operator if the
result has more than 16383 digits after the decimal point by rounding
the result. Overflow errors should only occur if the result has too
many digits *before* the decimal point.
Discussion: https://postgr.es/m/CAEZATCUmeFWCrq2dNzZpRj5+6LfN85jYiDoqm+ucSXhb9U2TbA@mail.gmail.com
When sending queries in pipeline mode, we were careless about leaving
the connection in the right state so that PQgetResult would behave
correctly; trying to read further results after sending a query after
having read a result with an error would sometimes hang. Fix by
ensuring internal libpq state is changed properly. All the state
changes were being done by the callers of pqAppendCmdQueueEntry(); it
would have become too repetitious to have this logic in each of them, so
instead put it all in that function and relieve callers of the
responsibility.
Add a test to verify this case. Without the code fix, this new test
hangs sometimes.
Also, document that PQisBusy() would return false when no queries are
pending result. This is not intuitively obvious, and NULL would be
obtained by calling PQgetResult() at that point, which is confusing.
Wording by Boris Kolpackov.
In passing, fix bogus use of "false" to mean "0", per Ranier Vilela.
Backpatch to 14.
Author: Álvaro Herrera <alvherre@alvh.no-ip.org>
Reported-by: Boris Kolpackov <boris@codesynthesis.com>
Discussion: https://postgr.es/m/boris.20210624103805@codesynthesis.com
Commit 7266d0997 added code to pull up simple constant function
results, converting the RTE_FUNCTION RTE to a dummy RTE_RESULT
RTE since it no longer need be scanned. But I forgot to clear
the LATERAL flag if the RTE has it set. If the function reduced
to a constant, it surely contains no lateral references so this
simplification is logically OK. It's needed because various other
places will Assert that RESULT RTEs aren't LATERAL.
Per bug #17097 from Yaoguang Chen. Back-patch to v13 where the
faulty code came in.
Discussion: https://postgr.es/m/17097-3372ef9f798fc94f@postgresql.org
Since the executor can't cope with a utility statement appearing
as a node of a plan tree, we can't support cases where a rewrite
rule inserts a NOTIFY into an INSERT/UPDATE/DELETE command appearing
in a WITH clause of a larger query. (One can imagine ways around
that, but it'd be a new feature not a bug fix, and so far there's
been no demand for it.) RewriteQuery checked for this, but it
missed the case where the DML command rewrites to *only* a NOTIFY.
That'd lead to crashes later on in planning. Add the missed check,
and improve the level of testing of this area.
Per bug #17094 from Yaoguang Chen. It's been busted since WITH
was introduced, so back-patch to all supported branches.
Discussion: https://postgr.es/m/17094-bf15dff55eaf2e28@postgresql.org
There was talk about adding units all the way up to yottabytes but it
seems quite far-fetched that anyone would need those. Since such large
units are not exactly commonplace, it seems unlikely that having
pg_size_pretty outputting unit any larger than petabytes would actually be
helpful to anyone.
Since petabytes are on the horizon, let's just add those only. Maybe one
day we'll get to add additional units, but it will likely be a while
before we'll need to think beyond petabytes in regards to the size of a
database.
Author: David Christensen
Discussion: https://postgr.es/m/CAOxo6XKmHc_WZip-x5QwaOqFEiCq_SVD0B7sbTZQk+qqcn2qaw@mail.gmail.com
Due to how pg_size_pretty(bigint) was implemented, it's possible that when
given a negative number of bytes that the returning value would not match
the equivalent positive return value when given the equivalent positive
number of bytes. This was due to two separate issues.
1. The function used bit shifting to convert the number of bytes into
larger units. The rounding performed by bit shifting is not the same as
dividing. For example -3 >> 1 = -2, but -3 / 2 = -1. These two
operations are only equivalent with positive numbers.
2. The half_rounded() macro rounded towards positive infinity. This meant
that negative numbers rounded towards zero and positive numbers rounded
away from zero.
Here we fix#1 by dividing the values instead of bit shifting. We fix#2
by adjusting the half_rounded macro always to round away from zero.
Additionally, adjust the pg_size_pretty(numeric) function to be more
explicit that it's using division rather than bit shifting. A casual
observer might have believed bit shifting was used due to a static
function being named numeric_shift_right. However, that function was
calculating the divisor from the number of bits and performed division.
Here we make that more clear. This change is just cosmetic and does not
affect the return value of the numeric version of the function.
Here we also add a set of regression tests both versions of
pg_size_pretty() which test the values directly before and after the
function switches to the next unit.
This bug was introduced in 8a1fab36a. Prior to that negative values were
always displayed in bytes.
Author: Dean Rasheed, David Rowley
Discussion: https://postgr.es/m/CAEZATCXnNW4HsmZnxhfezR5FuiGgp+mkY4AzcL5eRGO4fuadWg@mail.gmail.com
Backpatch-through: 9.6, where the bug was introduced.
Most error messages about a relkind that was not supported or
appropriate for the command was of the pattern
"relation \"%s\" is not a table, foreign table, or materialized view"
This style can become verbose and tedious to maintain. Moreover, it's
not very helpful: If I'm trying to create a comment on a TOAST table,
which is not supported, then the information that I could have created
a comment on a materialized view is pointless.
Instead, write the primary error message shorter and saying more
directly that what was attempted is not possible. Then, in the detail
message, explain that the operation is not supported for the relkind
the object was. To simplify that, add a new function
errdetail_relkind_not_supported() that does this.
In passing, make use of RELKIND_HAS_STORAGE() where appropriate,
instead of listing out the relkinds individually.
Reviewed-by: Michael Paquier <michael@paquier.xyz>
Reviewed-by: Alvaro Herrera <alvherre@alvh.no-ip.org>
Discussion: https://www.postgresql.org/message-id/flat/dc35a398-37d0-75ce-07ea-1dd71d98f8ec@2ndquadrant.com
Similar to 50e17ad28, which allowed hash tables to be used for IN clauses
with a set of constants, here we add the same feature for NOT IN clauses.
NOT IN evaluates the same as: WHERE a <> v1 AND a <> v2 AND a <> v3.
Obviously, if we're using a hash table we must be exactly equivalent to
that and return the same result taking into account that either side of
the condition could contain a NULL. This requires a little bit of
special handling to make work with the hash table version.
When processing NOT IN, the ScalarArrayOpExpr's operator will be the <>
operator. To be able to build and lookup a hash table we must use the
<>'s negator operator. The planner checks if that exists and is hashable
and sets the relevant fields in ScalarArrayOpExpr to instruct the executor
to use hashing.
Author: David Rowley, James Coleman
Reviewed-by: James Coleman, Zhihong Yu
Discussion: https://postgr.es/m/CAApHDvoF1mum_FRk6D621edcB6KSHBi2+GAgWmioj5AhOu2vwQ@mail.gmail.com
The original coding was not quoting the complete failing command, and it
wasn't printing the reason for the failure either. Do both.
This is cosmetic only, so no backpatch.
Author: Álvaro Herrera <alvherre@alvh.no-ip.org>
Reviewed-by: Tom Lane <tgl@sss.pgh.pa.us>
Reviewed-by: Daniel Gustafsson <daniel@yesql.se>
Discussion: https://postgr.es/m/202106301524.eq5pblzstapj@alvherre.pgsql
In 741d7f104, I tried to make the reports from canceled steps come out
after the pg_cancel_backend() steps, since that was the most common
ordering before. However, that doesn't ensure that a canceled step
doesn't report even later, as shown in a recent failure on buildfarm
member idiacanthus. Rather than complicating things even more with
additional annotations, let's just force the cancel's effect to be
reported first. It's not *that* unnatural-looking.
Back-patch to v14 where these test cases appeared.
Report: https://buildfarm.postgresql.org/cgi-bin/show_log.pl?nm=idiacanthus&dt=2021-07-02%2001%3A40%3A04
Formerly various numeric aggregate functions supported parallel
aggregation by having each worker convert partial aggregate values to
Numeric and use numeric_send() as part of serializing their state.
That's problematic, since the range of Numeric is smaller than that of
NumericVar, so it's possible for it to overflow (on either side of the
decimal point) in cases that would succeed in non-parallel mode.
Fix by serializing NumericVars instead, to avoid the overflow risk and
ensure that parallel and non-parallel modes work the same.
A side benefit is that this improves the efficiency of the
serialization/deserialization code, which can make a noticeable
difference to performance with large numbers of parallel workers.
No back-patch due to risk from changing the binary format of the
aggregate serialization states, as well as lack of prior field
complaints and low probability of such overflows in practice.
Patch by me. Thanks to David Rowley for review and performance
testing, and Ranier Vilela for an additional suggestion.
Discussion: https://postgr.es/m/CAEZATCUmeFWCrq2dNzZpRj5+6LfN85jYiDoqm+ucSXhb9U2TbA@mail.gmail.com
Commit 0e69f705cc introduced code to analyze partitioned table;
however, that code fails to preserve pg_class.relhasindex correctly.
Fix by observing whether any indexes exist rather than accidentally
falling through to assuming none do.
Backpatch to 14.
Author: Alexander Pyhalov <a.pyhalov@postgrespro.ru>
Reviewed-by: Álvaro Herrera <alvherre@alvh.no-ip.org>
Reviewed-by: Zhihong Yu <zyu@yugabyte.com>
Discussion: https://postgr.es/m/CALNJ-vS1R3Qoe5t4tbzxrkpBtzRbPq1dDcW4RmA_a+oqweF30w@mail.gmail.com
The prove_installcheck recipe in src/Makefile.global.in was emitting
bogus paths for a couple of elements when used with PGXS. Here we create
a separate recipe for the PGXS case that does it correctly. We also take
the opportunity to make the make the file more readable by breaking up
the prove_installcheck and prove_check recipes across several lines, and
to remove the setting for REGRESS_SHLIB to src/test/recovery/Makefile,
which is the only set of tests that actually need it.
Backpatch to all live branches
Discussion: https://postgr.es/m/f2401388-936b-f4ef-a07c-a0bcc49b3300@dunslane.net
There is a syntactic ambiguity in the SQL standard. Since UNBOUNDED
is a non-reserved word, it could be the name of a function parameter
and be used as an expression. There is a grammar hack to resolve such
cases as the keyword. Add some tests to record this behavior.
Reviewed-by: Heikki Linnakangas <hlinnaka@iki.fi>
Discussion: https://www.postgresql.org/message-id/flat/b2a09a77-3c8f-7c68-c9b7-824054f87d98%40enterprisedb.com
* Fix enumeration of the multirange operators in calc_multirangesel() and
calc_multirangesel() switches.
* Add more regression tests for matching to empty ranges/multiranges.
Reported-by: Alexander Lakhin
Discussion: https://postgr.es/m/c5269c65-f967-77c5-ff7c-15e621c47f6a%40gmail.com
Author: Alexander Korotkov
Backpatch-through: 14, where multiranges were introduced
The original coding required that PQpipelineSync had been called before
the first call to PQgetResult, and failure to do that would result in an
unexpected NULL result being returned. Fix by setting the right state
when a query is sent, rather than leaving it unchanged and having
PQpipelineSync apply the necessary state change.
A new test case to verify the behavior is added, which relies on the new
PQsendFlushRequest() function added by commit a7192326c7.
Backpatch to 14, where pipeline mode was added.
Reported-by: Boris Kolpackov <boris@codesynthesis.com>
Author: Álvaro Herrera <alvherre@alvh.no-ip.org>
Discussion: https://postgr.es/m/boris.20210616110321@codesynthesis.com
Commit efbfb6424 added logic for reporting exactly which existing
partition conflicts when complaining that a new hash partition's
modulus isn't compatible with the existing ones. However, it
misunderstood the partitioning data structure, and would select
the wrong partition in some cases, or crash outright due to fetching
a bogus table OID in other cases.
Per bug #17076 from Alexander Lakhin. Fix by Amit Langote;
some further work on the code comments by me.
Discussion: https://postgr.es/m/17076-89a16ae835d329b9@postgresql.org
83158f7 has improved index_set_state_flags() so as it is possible to use
transactional updates when updating pg_index state flags, but there was
not really a test case which stressed directly the possibility it fixed.
This commit adds such a test, using a predicate that looks valid in
appearance but calls a stable function.
Author: Andrey Lepikhov
Discussion: https://postgr.es/m/9b905019-5297-7372-0ad2-e1a4bb66a719@postgrespro.ru
Backpatch-through: 9.6
specscanner.l leaked a kilobyte of memory per token of the spec file.
Apparently somebody thought that the introductory code block would be
executed once; but it's once per yylex() call.
A couple of functions in isolationtester.c leaked small amounts of
memory due to not bothering to free one-time allocations. Might
as well improve these so that valgrind gives this program a clean
bill of health. Also get rid of an ugly static variable.
Coverity complained about one of the one-time leaks, which led me
to try valgrind'ing isolationtester, which led to discovery of the
larger leak.
ALTER SUBSCRIPTION DROP PUBLICATION does not actually support
copy_data option, so remove it from tab completion.
Also, reword the error message that is thrown when all the
publications from a subscription are specified to be dropped.
Also, made few doc and cosmetic adjustments.
Author: Vignesh C <vignesh21@gmail.com>
Reviewed-by: Bharath Rupireddy <bharath.rupireddy@enterprisedb.com>
Reviewed-by: Japin Li <japinli@hotmail.com>
Discussion: https://www.postgresql.org/message-id/flat/CALDaNm21RwsDzs4xj14ApteAF7auyyomHNnp+NEL-sH8m-jMvQ@mail.gmail.com
For no obvious reason, isolationtester has always insisted that
session and step names be written with double quotes. This is
fairly tedious and does little for test readability, especially
since the names that people actually choose almost always look
like normal identifiers. Hence, let's tweak the lexer to allow
SQL-like identifiers not only double-quoted strings.
(They're SQL-like, not exactly SQL, because I didn't add any
case-folding logic. Also there's no provision for U&"..." names,
not that anyone's likely to care.)
There is one incompatibility introduced by this change: if you write
"foo""bar" with no space, that used to be taken as two identifiers,
but now it's just one identifier with an embedded quote mark.
I converted all the src/test/isolation/ specfiles to remove
unnecessary double quotes, but stopped there because my
eyes were glazing over already.
Like 741d7f104, back-patch to all supported branches, so that this
isn't a stumbling block for back-patching isolation test changes.
Discussion: https://postgr.es/m/759113.1623861959@sss.pgh.pa.us
Previously, isolationtester displayed SQL query results using some
ad-hoc code that clearly hadn't had much effort expended on it.
Field values longer than 14 characters weren't separated from
the next field, and usually caused misalignment of the columns
too. Also there was no visual separation of a query's result
from subsequent isolationtester output. This made test result
files confusing and hard to read.
To improve matters, let's use libpq's PQprint() function. Although
that's long since unused by psql, it's still plenty good enough
for the purpose here.
Like 741d7f104, back-patch to all supported branches, so that this
isn't a stumbling block for back-patching isolation test changes.
Discussion: https://postgr.es/m/582362.1623798221@sss.pgh.pa.us
The code to signal a running walsender when its reserved WAL size grows
too large is completely uncovered before this commit; this adds coverage
for that case.
This test involves sending SIGSTOP to walsender and walreceiver, then
advancing enough WAL for a checkpoint to trigger, then sending SIGCONT.
There's no precedent for STOP signalling in Perl tests, and my reading
of relevant manpages says it's likely to fail on Windows. Because of
this, this test is always skipped on that platform.
This version fixes a couple of rarely hit race conditions in the
previous attempt 09126984a263; most notably, both LOG string searches
are loops, not just the second one; we acquire the start-of-log position
before STOP-signalling; and reference the correct process name in the
test description. All per Tom Lane.
Author: Álvaro Herrera <alvherre@alvh.no-ip.org>
Discussion: https://postgr.es/m/202106102202.mjw4huiix7lo@alvherre.pgsql
We've long contended with isolation test results that aren't entirely
stable. Some test scripts insert long delays to try to force stable
results, which is not terribly desirable; but other erratic failure
modes remain, causing unrepeatable buildfarm failures. I've spent a
fair amount of time trying to solve this by improving the server-side
support code, without much success: that way is fundamentally unable
to cope with diffs that stem from chance ordering of arrival of
messages from different server processes.
We can improve matters on the client side, however, by annotating
the test scripts themselves to show the desired reporting order
of events that might occur in different orders. This patch adds
three types of annotations to deal with (a) test steps that might or
might not complete their waits before the isolationtester can see them
waiting; (b) test steps in different sessions that can legitimately
complete in either order; and (c) NOTIFY messages that might arrive
before or after the completion of a step in another session. We might
need more annotation types later, but this seems to be enough to deal
with the instabilities we've seen in the buildfarm. It also lets us
get rid of all the long delays that were previously used, cutting more
than a minute off the runtime of the isolation tests.
Back-patch to all supported branches, because the buildfarm
instabilities affect all the branches, and because it seems desirable
to keep isolationtester's capabilities the same across all branches
to simplify possible future back-patching of tests.
Discussion: https://postgr.es/m/327948.1623725828@sss.pgh.pa.us
This reverts commit 09126984a263; the test case added there failed once
in circumstances that remain mysterious. It seems better to remove the
test for now so that 14beta2 doesn't have random failures built in.
Generalize the INDEX_CLEANUP VACUUM parameter (and the corresponding
reloption): make it into a ternary style boolean parameter. It now
exposes a third option, "auto". The "auto" option (which is now the
default) enables the "bypass index vacuuming" optimization added by
commit 1e55e7d1.
"VACUUM (INDEX_CLEANUP TRUE)" is redefined to once again make VACUUM
simply do any required index vacuuming, regardless of how few dead
tuples are encountered during the first scan of the target heap relation
(unless there are exactly zero). This gives users a way of opting out
of the "bypass index vacuuming" optimization, if for whatever reason
that proves necessary. It is also expected to be used by PostgreSQL
developers as a testing option from time to time.
"VACUUM (INDEX_CLEANUP FALSE)" does the same thing as it always has: it
forcibly disables both index vacuuming and index cleanup. It's not
expected to be used much in PostgreSQL 14. The failsafe mechanism added
by commit 1e55e7d1 addresses the same problem in a simpler way.
INDEX_CLEANUP can now be thought of as a testing and compatibility
option.
Author: Peter Geoghegan <pg@bowt.ie>
Reviewed-By: Masahiko Sawada <sawada.mshk@gmail.com>
Reviewed-By: Justin Pryzby <pryzby@telsasoft.com>
Discussion: https://postgr.es/m/CAH2-WznrBoCST4_Gxh_G9hA8NzGUbeBGnOUC8FcXcrhqsv6OHQ@mail.gmail.com
The code to signal a running walsender when its reserved WAL size grows
too large is completely uncovered before this commit; this adds coverage
for that case.
This test involves sending SIGSTOP to walsender and walreceiver and
running a checkpoint while advancing WAL, then sending SIGCONT. There's
no precedent for this coding in Perl tests, and my reading of relevant
manpages says it's likely to fail on Windows. Because of this, this
test is always skipped on that platform.
Author: Álvaro Herrera <alvherre@alvh.no-ip.org>
Discussion: https://postgr.es/m/202106102202.mjw4huiix7lo@alvherre.pgsql
Ordinarily, a pg_policy.polroles array wouldn't list the same role
more than once; but CREATE POLICY does not prevent that. If we
perform DROP OWNED BY on a role that is listed more than once,
RemoveRoleFromObjectPolicy either suffered an assertion failure
or encountered a tuple-updated-by-self error. Rewrite it to cope
correctly with duplicate entries, and add a CommandCounterIncrement
call to prevent the other problem.
Per discussion, there's other cleanup that ought to happen here,
but this seems like the minimum essential fix.
Per bug #17062 from Alexander Lakhin. It's been broken all along,
so back-patch to all supported branches.
Discussion: https://postgr.es/m/17062-11f471ae3199ca23@postgresql.org
The fast default code added in Release 11 omitted to check that the
table a fast default was being added to was a plain table. Thus one
could be added to a foreign table, which predicably blows up. Here we
perform that check.
In addition, on the back branches, since some of these might have
escaped into the wild, if we encounter a missing value for
an attribute of something other than a plain table we ignore it.
Fixes bug #17056
Backpatch to release 11,
Reviewed by: Andres Freund, Álvaro Herrera and Tom Lane
aborted-keyrevoke_2.out was apparently needed when it was added (in
commit 0ac5ad513) to handle the case of serializable transaction mode.
However, the output in serializable mode actually matches the regular
aborted-keyrevoke.out file, and AFAICT has done so for a long time.
There's no need to keep dragging this variant along.
TestLib::perl2host can take a file argument as well as a directory
argument, so that code becomes substantially simpler. Also add comments
on why we're using forward slashes, and why we're setting
PERL_BADLANG=0.
Discussion: https://postgr.es/m/e9947bcd-20ee-027c-f0fe-01f736b7e345@dunslane.net
It has been spotted that multiranges lack of ability to decompose them into
individual ranges. Subscription and proper expanded object representation
require substantial work, and it's too late for v14. This commit
provides the implementation of unnest(multirange) and cast multirange as
an array of ranges, which is quite trivial.
unnest(multirange) is defined as a polymorphic procedure. The catalog
description of the cast underlying procedure is duplicated for each multirange
type because we don't have anyrangearray polymorphic type to use here.
Catversion is bumped.
Reported-by: Jonathan S. Katz
Discussion: https://postgr.es/m/flat/60258efe-bd7e-4886-82e1-196e0cac5433%40postgresql.org
Author: Alexander Korotkov
Reviewed-by: Justin Pryzby, Jonathan S. Katz, Zhihong Yu
This should have been updated in d2d8a229b, but it was overlooked.
According to 31a877f18 which added it, this file is meant to show the
results you get under default_transaction_isolation = serializable.
We've largely lost track of that goal in other isolation tests, but
as long as we've got this one, it should be right.
Noted while fooling about with the isolationtester.
An object found as dropped when digging into the list of objects
returned by pg_event_trigger_ddl_commands() could cause a cache lookup
error, as the calls grabbing for the object address and the type name
would fail if the object was missing.
Those lookup errors could be seen with combinations of ALTER TABLE
sub-commands involving identity columns. The lookup logic is changed in
this code path to get a behavior similar to any other SQL-callable
function by ignoring objects that are not found, taking advantage of
2a10fdc. The back-branches are not changed, as they require this commit
that is too invasive for stable branches.
While on it, add test cases to exercise event triggers with identity
columns, and stress more cases with the event ddl_command_end for
relations.
Author: Sven Klemm, Aleksander Alekseev, Michael Paquier
Discussion: https://postgr.es/m/CAMCrgp2R1cEXU53iYKtW6yVEp2_yKUz+z=3-CTrYpPP+xryRtg@mail.gmail.com
The extra checks added by the recompression of toast data introduced in
bbe0a81 is proving to have a performance impact on VACUUM or CLUSTER
even if no recompression is done. This is more noticeable with more
toastable columns that contain non-NULL values.
Improvements could be done to make those extra checks less expensive,
but that's not material for 14 at this stage, and we are not sure either
if the code path of VACUUM FULL/CLUSTER is adapted for this job.
Per discussion with several people, including Andres Freund, Robert
Haas, Álvaro Herrera, Tom Lane and myself.
Discussion: https://postgr.es/m/20210527003144.xxqppojoiwurc2iz@alap3.anarazel.de
Translate path slashes on target directory path. This was confusing old
branches, but is applied to all branches for the sake of uniformity.
Perl is perfectly able to understand paths with forward slashes.
Along the way, restore the previous archive_wait query, for the sake of
uniformity with other tests, per gripe from Tom Lane.
This is similar to the work done in 8279f68 for TestLib.pm, where
environment variables set may cause unwanted failures if using a
temporary installation with pg_regress. The list of variables reset is
adjusted in each stable branch depending on what is supported.
Comments are added to remember that the lists in TestLib.pm and
pg_regress.c had better be kept in sync.
Reviewed-by: Álvaro Herrera
Discussion: https://postgr.es/m/YMNR9GYDn+fHlMta@paquier.xyz
Backpatch-through: 9.6
Several TAP tests use poll_query_until() to wait for the postmaster
to restart. They were checking to see if a trivial query
(e.g. "SELECT 1") succeeds. However, that's problematic in the wake
of commit 11e9caff8, because now that we feed said query to psql
via stdin, we risk IPC::Run whining about a SIGPIPE failure if psql
quits before reading the query. Hence, we can't use a nonempty
query in cases where we need to wait for connection failures to
stop happening.
Per the precedent of commits c757a3da0 and 6d41dd045, we can pass
"undef" as the query in such cases to ensure that IPC::Run has
nothing to write. However, then we have to say that the expected
output is empty, and this exposes a deficiency in poll_query_until:
if psql fails altogether and returns empty stdout, poll_query_until
will treat that as a success! That's because, contrary to its
documentation, it makes no actual check for psql failure, looking
neither at the exit status nor at stderr.
To fix that, adjust poll_query_until to insist on empty stderr as
well as a stdout match. (I experimented with checking exit status
instead, but it seems that psql often does exit(1) in cases that we
need to consider successes. That might be something to fix someday,
but it would be a non-back-patchable behavior change.)
Back-patch to v10. The test cases needing this exist only as far
back as v11, but it seems wise to keep poll_query_until's behavior
the same in v10, in case we back-patch another such test case in
future. (9.6 does not currently need this change, because in that
branch poll_query_until can't be told to accept empty stdout as
a success case.)
Per assorted buildfarm failures, mostly on hoverfly.
Discussion: https://postgr.es/m/CAA4eK1+zM6L4QSA1XMvXY_qqWwdUmqkOS1+hWvL8QcYEBGA1Uw@mail.gmail.com
Commit caba8f0d43 wasn't quite right for msys, as demonstrated by
several buildfarm animals, including jacana and fairywren. We need to
use the msys perl in the archive command, but call it in such a way that
Windows will understand the path. Furthermore, inside the copy script we
need to convert a Windows path to an msys path.
ab55d74 has introduced some tests with rows found as missing in logical
replication subscriptions for partitioned tables, relying on a logic
with a lookup of the logs generated, scanning the whole file. This
commit makes the logic more precise, by scanning the logs only from the
position before the key queries are run to the position where we check
for the logs. This will reduce the risk of issues with log patterns
overlapping with each other if those tests get more complicated in the
future.
Per discussion with Tom Lane.
Discussion: https://postgr.es/m/YMP+Gx2S8meYYHW4@paquier.xyz
Backpatch-through: 13
apply_handle_tuple_routing(), having detected and reported that
the tuple it needed to update didn't exist, tried to update that
tuple anyway, leading to a null-pointer dereference.
logicalrep_partition_open() failed to ensure that the
LogicalRepPartMapEntry it built for a partition was fully
independent of that for the partition root, leading to
trouble if the root entry was later freed or rebuilt.
Meanwhile, on the publisher's side, pgoutput_change() sometimes
attempted to apply execute_attr_map_tuple() to a NULL tuple.
The first of these was reported by Sergey Bernikov in bug #17055;
I found the other two while developing some test cases for this
sadly under-tested code.
Diagnosis and patch for the first issue by Amit Langote; patches
for the others by me; new test cases by me. Back-patch to v13
where this logic came in.
Discussion: https://postgr.es/m/17055-9ba800ec8522668b@postgresql.org
Commit acb7e4eb6b added a new implementation for PQsendQuery so that
it works in pipeline mode (by using extended query protocol), but it
behaves differently from the 'Q' message (in simple query protocol) used
by regular implementation: the new one doesn't close the unnamed portal.
Change the new code to have identical behavior to the old.
Reported-by: Yura Sokolov <y.sokolov@postgrespro.ru>
Author: Álvaro Herrera <alvherre@alvh.no-ip.org>
Discussion: https://postgr.es/m/202106072107.d4i55hdscxqj@alvherre.pgsql
We have a dozen PQset*() functions. PQresultSetInstanceData() and this
were the libpq setter functions having a different word order. Adopt
the majority word order.
Reviewed by Alvaro Herrera and Robert Haas, though this choice of name
was not unanimous.
Discussion: https://postgr.es/m/20210605060555.GA216695@rfd.leadboat.com
Commit 2453ea142 redefined pg_proc.proargtypes to include the types of
OUT parameters, for procedures only. While that had some advantages
for implementing the SQL-spec behavior of DROP PROCEDURE, it was pretty
disastrous from a number of other perspectives. Notably, since the
primary key of pg_proc is name + proargtypes, this made it possible to
have multiple procedures with identical names + input arguments and
differing output argument types. That would make it impossible to call
any one of the procedures by writing just NULL (or "?", or any other
data-type-free notation) for the output argument(s). The change also
seems likely to cause grave confusion for client applications that
examine pg_proc and expect the traditional definition of proargtypes.
Hence, revert the definition of proargtypes to what it was, and
undo a number of complications that had been added to support that.
To support the SQL-spec behavior of DROP PROCEDURE, when there are
no argmode markers in the command's parameter list, we perform the
lookup both ways (that is, matching against both proargtypes and
proallargtypes), succeeding if we get just one unique match.
In principle this could result in ambiguous-function failures
that would not happen when using only one of the two rules.
However, overloading of procedure names is thought to be a pretty
rare usage, so this shouldn't cause many problems in practice.
Postgres-specific code such as pg_dump can defend against any
possibility of such failures by being careful to specify argmodes
for all procedure arguments.
This also fixes a few other bugs in the area of CALL statements
with named parameters, and improves the documentation a little.
catversion bump forced because the representation of procedures
with OUT arguments changes.
Discussion: https://postgr.es/m/3742981.1621533210@sss.pgh.pa.us
This only happens if (1) the new standby has no WAL available locally,
(2) the new standby is starting from the old timeline, (3) the promotion
happened in the WAL segment from which the new standby is starting,
(4) the timeline history file for the new timeline is available from
the archive but the WAL files for are not (i.e. this is a race),
(5) the WAL files for the new timeline are available via streaming,
and (6) recovery_target_timeline='latest'.
Commit ee994272ca introduced this
logic and was an improvement over the previous code, but it mishandled
this case. If recovery_target_timeline='latest' and restore_command is
set, validateRecoveryParameters() can change recoveryTargetTLI to be
different from receiveTLI. If streaming is then tried afterward,
expectedTLEs gets initialized with the history of the wrong timeline.
It's supposed to be a list of entries explaining how to get to the
target timeline, but in this case it ends up with a list of entries
explaining how to get to the new standby's original timeline, which
isn't right.
Dilip Kumar and Robert Haas, reviewed by Kyotaro Horiguchi.
Discussion: http://postgr.es/m/CAFiTN-sE-jr=LB8jQuxeqikd-Ux+jHiXyh4YDiZMPedgQKup0g@mail.gmail.com
gram.y should discard NULL pointers (empty statements) when
assembling a routine_body_stmt_list, as it does for other
sorts of statement lists.
Julien Rouhaud and Tom Lane, per report from Noah Misch.
Discussion: https://postgr.es/m/20210606044418.GA297923@rfd.leadboat.com
When run on a server using default_toast_compression set to LZ4, this
test would fail because of a consistency issue with the order of the
tuples treated. LZ4 causes one tuple to be stored inline instead of
getting externalized. As the goal of this test is to check after data
stored externally, stick to pglz as the compression algorithm used, so
as all data of this test is stored the way it should.
Analyzed-by: Dilip Kumar
Discussion: https://postgr.es/m/YLrDWxJgM8WWMoCg@paquier.xyz
The Msys shell mangles certain patterns in its command line, so avoid
handing arbitrary SQL to psql on the command line and instead use
IPC::Run's redirection facility for stdin. This pattern is already
mostly whats used, but query_poll_until() was not doing the right thing.
Problem discovered on the buildfarm when a new TAP test failed on msys.
Various environment variables were not getting reset in the TAP tests,
which would cause failures depending on the tests or the environment
variables involved. For example, PGSSL{MAX,MIN}PROTOCOLVERSION could
cause failures in the SSL tests. Even worse, a junk value of
PGCLIENTENCODING makes a server startup fail. The list of variables
reset is adjusted in each stable branch depending on what is supported.
While on it, simplify a bit the code per a suggestion from Andrew
Dunstan, using a list of variables instead of doing single deletions.
Reviewed-by: Andrew Dunstan, Daniel Gustafsson
Discussion: https://postgr.es/m/YLbjjRpucIeZ78VQ@paquier.xyz
Backpatch-through: 9.6
Previously there was no regression test for recovery pause feature.
This commit adds the test that checks
- recovery can be paused or resumed expectedly
- pg_get_wal_replay_pause_state() reports the correct pause state
- the paused state ends and promotion continues if a promotion
is triggered while recovery is paused
Suggested-by: Michael Paquier
Author: Fujii Masao
Reviewed-by: Kyotaro Horiguchi, Dilip Kumar
Discussion: https://postgr.es/m/YKNirzqM1HYyk5h4@paquier.xyz
This case should be disallowed, just as FOR UPDATE with a plain
GROUP BY is disallowed; FOR UPDATE only makes sense when each row
of the query result can be identified with a single table row.
However, we missed teaching CheckSelectLocking() to check
groupingSets as well as groupClause, so that it would allow
degenerate grouping sets. That resulted in a bad plan and
a null-pointer dereference in the executor.
Looking around for other instances of the same bug, the only one
I found was in examine_simple_variable(). That'd just lead to
silly estimates, but it should be fixed too.
Per private report from Yaoguang Chen.
Back-patch to all supported branches.
Release memory allocated when creating the tuple-conversion map and its
component TupleDescs when its owning sync entry is invalidated.
TupleDescs must also be freed when no map is deemed necessary, to begin
with.
Reported-by: Andres Freund
Author: Amit Langote
Reviewed-by: Takamichi Osumi, Amit Kapila
Backpatch-through: 13, where it was introduced
Discussion: https://postgr.es/m/MEYP282MB166933B1AB02B4FE56E82453B64D9@MEYP282MB1669.AUSP282.PROD.OUTLOOK.COM
create_projection_plan contains a hidden assumption (here made
explicit by an Assert) that a projection-capable Path will yield a
projection-capable Plan. Unfortunately, that assumption is violated
only a few lines away, by create_projection_plan itself. This means
that two stacked ProjectionPaths can yield an outcome where we try to
jam the upper path's tlist into a non-projection-capable child node,
resulting in an invalid plan.
There isn't any good reason to have stacked ProjectionPaths; indeed the
whole concept is faulty, since the set of Vars/Aggs/etc needed by the
upper one wouldn't necessarily be available in the output of the lower
one, nor could the lower one create such values if they weren't
available from its input. Hence, we can fix this by adjusting
create_projection_path to strip any top-level ProjectionPath from the
subpath it's given. (This amounts to saying "oh, we changed our
minds about what we need to project here".)
The test case added here only fails in v13 and HEAD; before that, we
don't attempt to shove the Sort into the parallel part of the plan,
for reasons that aren't entirely clear to me. However, all the
directly-related code looks generally the same as far back as v11,
where the hazard was introduced (by d7c19e62a). So I've got no faith
that the same type of bug doesn't exist in v11 and v12, given the
right test case. Hence, back-patch the code changes, but not the
irrelevant test case, into those branches.
Per report from Bas Poot.
Discussion: https://postgr.es/m/534fca83789c4a378c7de379e9067d4f@politie.nl
Braces were referred in some error messages as only brackets (not curly
brackets or curly braces), which can be confusing as other types of
brackets could be used.
While on it, add one test to check after the case of junk characters
detected after a right brace.
Author: Kyotaro Horiguchi
Discussion: https://postgr.es/m/20210514.153153.1814935914483287479.horikyota.ntt@gmail.com
Redefine '\0' (InvalidCompressionMethod) as meaning "if we need to
compress, use the current setting of default_toast_compression".
This allows '\0' to be a suitable default choice regardless of
datatype, greatly simplifying code paths that initialize tupledescs
and the like. It seems like a more user-friendly approach as well,
because now the default compression choice doesn't migrate into table
definitions, meaning that changing default_toast_compression is
usually sufficient to flip an installation's behavior; one needn't
tediously issue per-column ALTER SET COMPRESSION commands.
Along the way, fix a few minor bugs and documentation issues
with the per-column-compression feature. Adopt more robust
APIs for SetIndexStorageProperties and GetAttributeCompression.
Bump catversion because typical contents of attcompression will now
be different. We could get away without doing that, but it seems
better to ensure v14 installations all agree on this. (We already
forced initdb for beta2, anyway.)
Discussion: https://postgr.es/m/626613.1621787110@sss.pgh.pa.us
The path needs to be set to refer to the build directory, not the
current directory, because that's actually the source directory at
that point.
fix for 6abc8c2596
Same as 5e0b1aeb2d, for the companion test file.
This one seems lower probability (only two failures in a month of runs);
I was hardly able to reproduce a failure without a patch, so the fact
that I was also unable to reproduce one with it doesn't say anything.
We'll have to wait for further buildfarm results to see if we need any
further adjustments.
Discussion: https://postgr.es/m/20210524090712.GA3771394@rfd.leadboat.com
This recently added test has shown to be too sensitive to timing when
sending a cancel to a session waiting for a lock.
We fix this by running a no-op query in the blocked session immediately
after the cancel; this avoids the session that sent the cancel sending
another query immediately before the cancel has been reported.
Idea by Noah Misch.
With that fix, we sometimes see that the cancel error report is shown
only relative to the step that is cancelled, instead of together with
the step that sends the cancel. To increase the probability that both
steps are shown togeter, add a 0.1s sleep to the cancel. In normal
conditions this appears sufficient to silence most failures, but we'll
see that the slower buildfarm members say about it.
Reported-by: Takamichi Osumi <osumi.takamichi@fujitsu.com>
Discussion: https://postgr.es/m/OSBPR01MB4888C4ABA361C7E81094AC66ED269@OSBPR01MB4888.jpnprd01.prod.outlook.com
The error messages, docs, and one of the options were using
'parallel degree' to indicate parallelism used by vacuum command. We
normally use 'parallel workers' at other places so change it for parallel
vacuum accordingly.
Author: Bharath Rupireddy
Reviewed-by: Dilip Kumar, Amit Kapila
Backpatch-through: 13
Discussion: https://postgr.es/m/CALj2ACWz=PYrrFXVsEKb9J1aiX4raA+UBe02hdRp_zqDkrWUiw@mail.gmail.com
Result Cache, added in 9eacee2e6 neglected to properly adjust the plan
references in setrefs.c. This could lead to the following error during
EXPLAIN:
ERROR: cannot decompile join alias var in plan tree
Fix that.
Bug: 17030
Reported-by: Hans Buschmann
Discussion: https://postgr.es/m/17030-5844aecae42fe223@postgresql.org
This was previously allowed, but I think that was just an oversight.
It's a clear violation of the rule that a generated column cannot
depend on itself or other generated columns. Moreover, because the
code was relying on the assumption that no such cross-references
exist, it was pretty easy to crash ALTER TABLE and perhaps other
places. Even if you managed not to crash, you got quite unstable,
implementation-dependent results.
Per report from Vitaly Ustinov.
Back-patch to v12 where GENERATED came in.
Discussion: https://postgr.es/m/CAM_DEiWR2DPT6U4xb-Ehigozzd3n3G37ZB1+867zbsEVtYoJww@mail.gmail.com
We consider this supported (though I've got my doubts that it's a
good idea, because tableoid is not immutable). However, several
code paths failed to fill the field in soon enough, causing such
a GENERATED expression to see zero or the wrong value. This
occurred when ALTER TABLE adds a new GENERATED column to a table
with existing rows, and during regular INSERT or UPDATE on a
foreign table with GENERATED columns.
Noted during investigation of a report from Vitaly Ustinov.
Back-patch to v12 where GENERATED came in.
Discussion: https://postgr.es/m/CAM_DEiWR2DPT6U4xb-Ehigozzd3n3G37ZB1+867zbsEVtYoJww@mail.gmail.com
COMMIT/ROLLBACK necessarily destroys all snapshots within the session.
The original implementation of intra-procedure transactions just
cavalierly did that, ignoring the fact that this left us executing in
a rather different environment than normal. In particular, it turns
out that handling of toasted datums depends rather critically on there
being an outer ActiveSnapshot: otherwise, when SPI or the core
executor pop whatever snapshot they used and return, it's unsafe to
dereference any toasted datums that may appear in the query result.
It's possible to demonstrate "no known snapshots" and "missing chunk
number N for toast value" errors as a result of this oversight.
Historically this outer snapshot has been held by the Portal code,
and that seems like a good plan to preserve. So add infrastructure
to pquery.c to allow re-establishing the Portal-owned snapshot if it's
not there anymore, and add enough bookkeeping support that we can tell
whether it is or not.
We can't, however, just re-establish the Portal snapshot as part of
COMMIT/ROLLBACK. As in normal transaction start, acquiring the first
snapshot should wait until after SET and LOCK commands. Hence, teach
spi.c about doing this at the right time. (Note that this patch
doesn't fix the problem for any PLs that try to run intra-procedure
transactions without using SPI to execute SQL commands.)
This makes SPI's no_snapshots parameter rather a misnomer, so in HEAD,
rename that to allow_nonatomic.
replication/logical/worker.c also needs some fixes, because it wasn't
careful to hold a snapshot open around AFTER trigger execution.
That code doesn't use a Portal, which I suspect someday we're gonna
have to fix. But for now, just rearrange the order of operations.
This includes back-patching the recent addition of finish_estate()
to centralize the cleanup logic there.
This also back-patches commit 2ecfeda3e into v13, to improve the
test coverage for worker.c (it was that test that exposed that
worker.c's snapshot management is wrong).
Per bug #15990 from Andreas Wicht. Back-patch to v11 where
intra-procedure COMMIT was added.
Discussion: https://postgr.es/m/15990-eee2ac466b11293d@postgresql.org
While applying the truncate change, the logical apply worker acquires
RowExclusiveLock on the relation being truncated. This allowed truncate on
the relation at a time by two apply workers which lead to a deadlock. The
reason was that one of the workers after updating the pg_class tuple tries
to acquire SHARE lock on the relation and started to wait for the second
worker which has acquired RowExclusiveLock on the relation. And when the
second worker tries to update the pg_class tuple, it starts to wait for
the first worker which leads to a deadlock. Fix it by acquiring
AccessExclusiveLock on the relation before applying the truncate change as
we do for normal truncate operation.
Author: Peter Smith, test case by Haiying Tang
Reviewed-by: Dilip Kumar, Amit Kapila
Backpatch-through: 11
Discussion: https://postgr.es/m/CAHut+PsNm43p0jM+idTvWwiGZPcP0hGrHMPK9TOAkc+a4UpUqw@mail.gmail.com
exec_for_query() normally tries to prefetch a few rows at a time
from the query being iterated over, so as to reduce executor
entry/exit overhead. Unfortunately this is unsafe if we have
COMMIT or ROLLBACK within the loop, because there might be
TOAST references in the data that we prefetched but haven't
yet examined. Immediately after the COMMIT/ROLLBACK, we have
no snapshots in the session, meaning that VACUUM is at liberty
to remove recently-deleted TOAST rows.
This was originally reported as a case triggering the "no known
snapshots" error in init_toast_snapshot(), but even if you miss
hitting that, you can get "missing toast chunk", as illustrated
by the added isolation test case.
To fix, just disable prefetching in non-atomic contexts. Maybe
there will be performance complaints prompting us to work harder
later, but it's not clear at the moment that this really costs
much, and I doubt we'd want to back-patch any complicated fix.
In passing, adjust that error message in init_toast_snapshot()
to be a little clearer about the likely cause of the problem.
Patch by me, based on earlier investigation by Konstantin Knizhnik.
Per bug #15990 from Andreas Wicht. Back-patch to v11 where
intra-procedure COMMIT was added.
Discussion: https://postgr.es/m/15990-eee2ac466b11293d@postgresql.org
A lamentable oversight on my part meant that when PostgresVersion.pm was
added in commit 4c4eaf3d19 provision to install it was not added to the
Makefile, so it was not installed along with the other perl modules.
Older versions of perl on Windows don't like the list form of pipe open,
and perlcritic doesn't like the string form of open, so we avoid both
with a simpler formulation using qx{}.
Per complaint from Amit Kapila.
Recently we refactored things so that pg_regress makes the
"testtablespace" subdirectory used by the core regression tests,
instead of doing that in the makefiles. That had the undesirable
side effect of making such a subdirectory in every directory that
has "input" or "output" test files. Since these subdirectories
remain empty, git doesn't complain about them, but nonetheless
they're clutter.
To fix, invent an explicit --make-testtablespace-dir switch,
so that pg_regress only makes the subdirectory when explicitly
told to.
Discussion: https://postgr.es/m/2854388.1621284789@sss.pgh.pa.us
We were not waiting for a publisher to catch up with the subscriber after
creating a subscription. Now, it can happen that apply worker starts
replication even after we have disabled the subscription in the test. This
will make the test expect that there is no active slot whereas there
exists one. Fix this symptom by allowing the publisher to wait for
catching up with the subscription.
It is not a good idea to ensure if the slot is still active by checking
for walsender existence as we release the slot after we clean up the
walsender related memory. Fix that by checking the slot status in
pg_replication_slots.
Also, it is better to avoid repeated enabling/disabling of the
subscription.
Finally, we make autovacuum off for this test to avoid any empty
transaction appearing in the test while consuming changes.
Reported-by: as per buildfarm
Author: Vignesh C
Reviewed-by: Amit Kapila, Michael Paquier
Discussion: https://postgr.es/m/CAA4eK1+uW1UGDHDz-HWMHMen76mKP7NJebOTZN4uwbyMjaYVww@mail.gmail.com
Formerly we just relied on operator classes that assert longValuesOK
to eventually shorten the leaf value enough to fit on an index page.
That fails since the introduction of INCLUDE-column support (commit
09c1c6ab4), because the INCLUDE columns might alone take up more
than a page, meaning no amount of leaf-datum compaction will get
the job done. At least with spgtextproc.c, that leads to an infinite
loop, since spgtextproc.c won't throw an error for not being able
to shorten the leaf datum anymore.
To fix without breaking cases that would otherwise work, add logic
to spgdoinsert() to verify that the leaf tuple size is decreasing
after each "choose" step. Some opclasses might not decrease the
size on every single cycle, and in any case, alignment roundoff
of the tuple size could obscure small gains. Therefore, allow
up to 10 cycles without additional savings before throwing an
error. (Perhaps this number will need adjustment, but it seems
quite generous right now.)
As long as we've developed this logic, let's back-patch it.
The back branches don't have INCLUDE columns to worry about, but
this seems like a good defense against possible bugs in operator
classes. We already know that an infinite loop here is pretty
unpleasant, so having a defense seems to outweigh the risk of
breaking things. (Note that spgtextproc.c is actually the only
known opclass with longValuesOK support, so that this is all moot
for known non-core opclasses anyway.)
Per report from Dilip Kumar.
Discussion: https://postgr.es/m/CAFiTN-uxP_soPhVG840tRMQTBmtA_f_Y8N51G7DKYYqDh7XN-A@mail.gmail.com
Also "make reformat-dat-files".
The only change worthy of note is that pgindent messed up the formatting
of launcher.c's struct LogicalRepWorkerId, which led me to notice that
that struct wasn't used at all anymore, so I just took it out.
Several queries in the privileges regression test cause the planner
to apply the plpgsql function "leak()" to every element of the
histogram for atest12.b. Since commit 0c882e52a increased the size
of that histogram to 10000 entries, the test invokes that function
over 100000 times, which takes an absolutely unreasonable amount of
time in clobber-cache-always mode.
However, there's no real reason why that has to be a plpgsql
function: for the purposes of this test, all that matters is that
it not be marked leakproof. So we can replace the plpgsql
implementation with a direct call of int4lt, which has the same
behavior and is orders of magnitude faster. This is expected to
cut several hours off the buildfarm cycle time for CCA animals.
It has some positive impact in normal builds too, though that's
probably lost in the noise.
Back-patch to v13 where 0c882e52a came in.
Discussion: https://postgr.es/m/575884.1620626638@sss.pgh.pa.us
Having to maintain two lists of regression test scripts has proven
annoyingly error-prone. We can achieve the effect of the
serial_schedule by running the parallel_schedule with
"--max_connections=1"; so do that and remove serial_schedule.
This causes cosmetic differences in the progress output, but it
doesn't seem worth restructuring pg_regress to avoid that.
Discussion: https://postgr.es/m/899209.1620759506@sss.pgh.pa.us
opr_sanity's binary_coercible() function has always been meant
to match the parser's notion of binary coercibility, but it also
has always been a rather poor approximation of the parser's
real rules (as embodied in IsBinaryCoercible()). That hasn't
bit us so far, but it's predictable that it will eventually.
It also now emerges that implementing this check in plpgsql
performs absolutely horribly in clobber-cache-always testing.
(Perhaps we could do something about that, but I suspect it just
means that plpgsql is exploiting catalog caching to the hilt.)
Hence, let's replace binary_coercible() with a C shim that directly
invokes IsBinaryCoercible(), eliminating both the semantic hazard
and the performance issue.
Most of regress.c's C functions are declared in create_function_1,
but we can't simply move that to before opr_sanity/type_sanity
since those tests would complain about the resulting shell types.
I chose to split it into create_function_0 and create_function_1.
Since create_function_0 now runs as part of a parallel group while
create_function_1 doesn't, reduce the latter to create just those
functions that opr_sanity and type_sanity would whine about.
To make room for create_function_0 in the second parallel group
of tests, move tstypes to the third parallel group.
In passing, clean up some ordering deviations between
parallel_schedule and serial_schedule.
Discussion: https://postgr.es/m/292305.1620503097@sss.pgh.pa.us
It's unusual to have any resjunk columns in an ON CONFLICT ... UPDATE
list, but it can happen when MULTIEXPR_SUBLINK SubPlans are present.
If it happens, the ON CONFLICT UPDATE code path would end up storing
tuples that include the values of the extra resjunk columns. That's
fairly harmless in the short run, but if new columns are added to
the table then the values would become accessible, possibly leading
to malfunctions if they don't match the datatypes of the new columns.
This had escaped notice through a confluence of missing sanity checks,
including
* There's no cross-check that a tuple presented to heap_insert or
heap_update matches the table rowtype. While it's difficult to
check that fully at reasonable cost, we can easily add assertions
that there aren't too many columns.
* The output-column-assignment cases in execExprInterp.c lacked
any sanity checks on the output column numbers, which seems like
an oversight considering there are plenty of assertion checks on
input column numbers. Add assertions there too.
* We failed to apply nodeModifyTable's ExecCheckPlanOutput() to
the ON CONFLICT UPDATE tlist. That wouldn't have caught this
specific error, since that function is chartered to ignore resjunk
columns; but it sure seems like a bad omission now that we've seen
this bug.
In HEAD, the right way to fix this is to make the processing of
ON CONFLICT UPDATE tlists work the same as regular UPDATE tlists
now do, that is don't add "SET x = x" entries, and use
ExecBuildUpdateProjection to evaluate the tlist and combine it with
old values of the not-set columns. This adds a little complication
to ExecBuildUpdateProjection, but allows removal of a comparable
amount of now-dead code from the planner.
In the back branches, the most expedient solution seems to be to
(a) use an output slot for the ON CONFLICT UPDATE projection that
actually matches the target table, and then (b) invent a variant of
ExecBuildProjectionInfo that can be told to not store values resulting
from resjunk columns, so it doesn't try to store into nonexistent
columns of the output slot. (We can't simply ignore the resjunk columns
altogether; they have to be evaluated for MULTIEXPR_SUBLINK to work.)
This works back to v10. In 9.6, projections work much differently and
we can't cheaply give them such an option. The 9.6 version of this
patch works by inserting a JunkFilter when it's necessary to get rid
of resjunk columns.
In addition, v11 and up have the reverse problem when trying to
perform ON CONFLICT UPDATE on a partitioned table. Through a
further oversight, adjust_partition_tlist() discarded resjunk columns
when re-ordering the ON CONFLICT UPDATE tlist to match a partition.
This accidentally prevented the storing-bogus-tuples problem, but
at the cost that MULTIEXPR_SUBLINK cases didn't work, typically
crashing if more than one row has to be updated. Fix by preserving
resjunk columns in that routine. (I failed to resist the temptation
to add more assertions there too, and to do some minor code
beautification.)
Per report from Andres Freund. Back-patch to all supported branches.
Security: CVE-2021-32028
This set of commits has some bugs with known fixes, but at this late
stage in the release cycle it seems best to revert and resubmit next
time, along with some new automated test coverage for this whole area.
Commits reverted:
dc88460c: Doc: Review for "Optionally prefetch referenced data in recovery."
1d257577: Optionally prefetch referenced data in recovery.
f003d9f8: Add circular WAL decoding buffer.
323cbe7c: Remove read_page callback from XLogReader.
Remove the new GUC group WAL_RECOVERY recently added by a55a9847, as the
corresponding section of config.sgml is now reverted.
Discussion: https://postgr.es/m/CAOuzzgrn7iKnFRsB4MHp3UisEQAGgZMbk_ViTN4HV4-Ksq8zCg%40mail.gmail.com
Design problems were discovered in the handling of composite types and
record types that would cause some relevant versions not to be recorded.
Misgivings were also expressed about the use of the pg_depend catalog
for this purpose. We're out of time for this release so we'll revert
and try again.
Commits reverted:
1bf946bd: Doc: Document known problem with Windows collation versions.
cf002008: Remove no-longer-relevant test case.
ef387bed: Fix bogus collation-version-recording logic.
0fb0a050: Hide internal error for pg_collation_actual_version(<bad OID>).
ff942057: Suppress "warning: variable 'collcollate' set but not used".
d50e3b1f: Fix assertion in collation version lookup.
f24b1569: Rethink extraction of collation dependencies.
257836a7: Track collation versions for indexes.
cd6f479e: Add pg_depend.refobjversion.
7d1297df: Remove pg_collation.collversion.
Discussion: https://postgr.es/m/CA%2BhUKGLhj5t1fcjqAu8iD9B3ixJtsTNqyCCD4V0aTO9kAKAjjA%40mail.gmail.com
When ALTER TABLE .. ALTER CONSTRAINT changes deferrability properties
changed in a partitioned table, we failed to propagate those changes
correctly to partitions and to triggers. Repair by adding a recursion
mechanism to affect all derived constraints and all derived triggers.
(In particular, recurse to partitions even if their respective parents
are already in the desired state: it is possible for the partitions to
have been altered individually.) Because foreign keys involve tables in
two sides, we cannot use the standard ALTER TABLE recursion mechanism,
so we invent our own by following pg_constraint.conparentid down.
When ALTER TABLE .. ALTER CONSTRAINT is invoked on the derived
pg_constraint object that's automaticaly created in a partition as a
result of a constraint added to its parent, raise an error instead of
pretending to work and then failing to modify all the affected triggers.
Before this commit such a command would be allowed but failed to affect
all triggers, so it would silently misbehave. (Restoring dumps of
existing databases is not affected, because pg_dump does not produce
anything for such a derived constraint anyway.)
Add some tests for the case.
Backpatch to 11, where foreign key support was added to partitioned
tables by commit 3de241dba8. (A related change is commit f56f8f8da6
in pg12 which added support for FKs *referencing* partitioned tables;
this is what forces us to use an ad-hoc recursion mechanism for this.)
Diagnosed by Tom Lane from bug report from Ron L Johnson. As of this
writing, no reviews were offered.
Discussion: https://postgr.es/m/75fe0761-a291-86a9-c8d8-4906da077469@gmail.com
Discussion: https://postgr.es/m/3144850.1607369633@sss.pgh.pa.us
When running ALTER TABLE t2 INHERIT t1, we must check that columns in
t2 that correspond to a generated column in t1 are also generated and
have the same generation expression. Otherwise, this would allow
creating setups that a normal CREATE TABLE sequence would not allow.
Discussion: https://www.postgresql.org/message-id/22de27f6-7096-8d96-4619-7b882932ca25@2ndquadrant.com
Commit 824bf7190 introduced a new search of the NFAs generated by
regex compilation. I failed to think hard about the performance
characteristics of that search, with the predictable outcome
that it's bad: weird regexes can trigger exponential search time.
Worse, there's no check-for-interrupt in that code, so you can't
even cancel the query if this happens.
Fix by introducing memo-ization of the search results, so that any one
NFA state need be examined in detail just once. This potentially uses
a lot of memory, but we can bound the memory usage by putting a limit
on the number of states for which we'll try to prove match-all-ness.
That is sane because we already have a limit (DUPINF) on the maximum
finite string length that a matchall regex can match; and patterns
that involve much more than DUPINF states would probably exceed that
limit anyway.
Also, rearrange the logic so that we check the basic is-the-graph-
all-RAINBOW-arcs property before we start the recursive search to
determine path lengths. This will ensure that we fall out quickly
whenever the NFA couldn't possibly be matchall.
Also stick in a check-for-interrupt, just in case these measures
don't completely eliminate the risk of slowness.
Discussion: https://postgr.es/m/3483895.1619898362@sss.pgh.pa.us
websearch_to_tsquery() splits text in quotes into tokens and connects them with
phrase operator on its own. However, that leads to surprising results when the
token contains no words.
For instance, websearch_to_tsquery('"aaa: bbb"') is 'aaa <2> bbb', because
it is equivalent of to_tsquery(E'aaa <-> \':\' <-> bbb'). But
websearch_to_tsquery('"aaa: bbb"') has to be 'aaa <-> bbb' in order to match
to_tsvector('aaa: bbb').
Since 0c4f355c6a, we anyway connect lexemes of complex tokens with phrase
operators. Thus, let's just websearch_to_tsquery() parse text in quotes as
a single token. Therefore, websearch_to_tsquery() should process the quoted
text in the same way phraseto_tsquery() does. This solution is what we exactly
need and also simplifies the code.
This commit is an incompatible change, so we don't backpatch it.
Reported-by: Valentin Gatien-Baron
Discussion: https://postgr.es/m/CA%2B0DEqiZs7gdOd4ikmg%3D0UWG%2BSwWOLxPsk_JW-sx9WNOyrb0KQ%40mail.gmail.com
Author: Alexander Korotkov
Reviewed-by: Tom Lane, Zhihong Yu
Here we adjust the EXPLAIN ANALYZE output for Result Cache so that we
don't show any Result Cache stats for parallel workers who don't
contribute anything to Result Cache plan nodes.
I originally had ideas that workers who don't help could still have their
Result Cache stats displayed. The idea with that was so that I could
write some parallel Result Cache regression tests that show the EXPLAIN
ANALYZE output. However, I realized a little too late that such tests
would just not be possible to have run in a stable way on the buildfarm.
With that knowledge, before 9eacee2e6 went in, I had removed all of the
tests that were showing the EXPLAIN ANALYZE output of a parallel Result
Cache plan, however, I forgot to put back the code that adjusts the
EXPLAIN output to hide the Result Cache stats for parallel workers who
were not fast enough to help out before query execution was over. All
other nodes behave this way and so should Result Cache.
Additionally, with this change, it now seems safe enough to remove the SET
force_parallel_mode = off that I had added to the regression tests.
Also, perform some cleanup in the partition_prune tests. I had adjusted
the explain_parallel_append() function to sanitize the Result Cache
EXPLAIN ANALYZE output. However, since I didn't actually include any
parallel Result Cache tests that show their EXPLAIN ANALYZE output, that
code does nothing and can be removed.
In passing, move the setting of memPeakKb into the scope where it's used.
Reported-by: Amit Khandekar
Author: David Rowley, Amit Khandekar
Discussion: https://postgr.es/m/CAJ3gD9d8SkfY95GpM1zmsOtX2-Ogx5q-WLsf8f0ykEb0hCRK3w@mail.gmail.com
Makes partition descriptor acquisition faster during the transient
period in which a partition is in the process of being detached.
This also adds the restriction that only one partition can be in
pending-detach state for a partitioned table.
While at it, return find_inheritance_children() API to what it was
before 71f4c8c6f7, and create a separate
find_inheritance_children_extended() that returns detailed info about
detached partitions.
(This incidentally fixes a bug in 8aba932251 whereby a memory context
holding a transient partdesc is reparented to a NULL PortalContext,
leading to permanent leak of that memory. The fix is to no longer rely
on reparenting contexts to PortalContext. Reported by Amit Langote.)
Per gripe from Amit Langote
Discussion: https://postgr.es/m/CA+HiwqFgpP1LxJZOBYGt9rpvTjXXkg5qG2+Xch2Z1Q7KrqZR1A@mail.gmail.com
Attempting to use this function with event triggers failed, as, since
its introduction in a676201, this code has never associated an object
name with event triggers. This addresses the failure by adding the
event trigger name to the set defining its object address.
Note that regression tests are added within event_trigger and not
object_address to avoid issues with concurrent connections in parallel
schedules.
Author: Joel Jacobson
Discussion: https://postgr.es/m/3c905e77-a026-46ae-8835-c3f6cd1d24c8@www.fastmail.com
Backpatch-through: 9.6
Handle the situation where perl swaps the order of operands of
the comparison operator. See `perldoc overload` for details:
The third argument is set to TRUE if (and only if) the two
operands have been swapped. Perl may do this to ensure that the
first argument ($self) is an object implementing the overloaded
operation, in line with general object calling conventions.
Previously, we used to use the array of size max_replication_slots to
store stats for replication slots. But that had two problems in the cases
where a message for dropping a slot gets lost: 1) the stats for the new
slot are not recorded if the array is full and 2) writing beyond the end
of the array if the user reduces the max_replication_slots.
This commit uses HTAB for replication slot statistics, resolving both
problems. Now, pgstat_vacuum_stat() search for all the dead replication
slots in stats hashtable and tell the collector to remove them. To avoid
showing the stats for the already-dropped slots, pg_stat_replication_slots
view searches slot stats by the slot name taken from pg_replication_slots.
Also, we send a message for creating a slot at slot creation, initializing
the stats. This reduces the possibility that the stats are accumulated
into the old slot stats when a message for dropping a slot gets lost.
Reported-by: Andres Freund
Author: Sawada Masahiko, test case by Vignesh C
Reviewed-by: Amit Kapila, Vignesh C, Dilip Kumar
Discussion: https://postgr.es/m/20210319185247.ldebgpdaxsowiflw@alap3.anarazel.de
The Truncate operation acquires an exclusive lock on the target relation
and indexes. It then waits for logical replication of the operation to
finish at commit. Now because we are acquiring the shared lock on the
target index to get index attributes in pgoutput while sending the
changes for the Truncate operation, it leads to a deadlock.
Actually, we don't need to acquire a lock on the target index as we build
the cache entry using a historic snapshot and all the later changes are
absorbed while decoding WAL. So, we wrote a special purpose function for
logical replication to get a bitmap of replica identity attribute numbers
where we get that information without locking the target index.
We decided not to backpatch this as there doesn't seem to be any field
complaint about this issue since it was introduced in commit 5dfd1e5a in
v11.
Reported-by: Haiying Tang
Author: Takamichi Osumi, test case by Li Japin
Reviewed-by: Amit Kapila, Ajin Cherian
Discussion: https://postgr.es/m/OS0PR01MB6113C2499C7DC70EE55ADB82FB759@OS0PR01MB6113.jpnprd01.prod.outlook.com
The tuple routing logic used by a logical replication worker can fire
triggers on relations part of a partition tree, but there was no test
coverage in this area. The existing script 003_constraints.pl included
something, but nothing when a tuple is applied across partitioned tables
on a subscriber.
Author: Amit Langote
Discussion: https://postgr.es/m/OS0PR01MB611383FA0FE92EB9DE21946AFB769@OS0PR01MB6113.jpnprd01.prod.outlook.com
As well as 'devel' version_stamp.pl provides for 'alphaN'
'betaN' and 'rcN', so teach PostgresVersion about those.
Also stash the version string instead of trying to reconstruct it during
stringification.
Discussion: https://postgr.es/m/YIHlw5nSgAHs4dK1@paquier.xyz
Adopt a more consistent policy about what slot-type-specific
getsysattr functions should do when system attributes are not
available. To wit, they should all throw the same user-oriented
error, rather than variously crashing or emitting developer-oriented
messages.
This closes a identifiable problem in commits a71cfc56b and
3fb93103a (in v13 and v12), so back-patch into those branches,
along with a test case to try to ensure we don't break it again.
It is not known that any of the former crash cases are reachable
in HEAD, but this seems like a good safety improvement in any case.
Discussion: https://postgr.es/m/141051591267657@mail.yandex.ru
During queries coming from ri_triggers.c, we need to omit partitions
that are marked pending detach -- otherwise, the RI query is tricked
into allowing a row into the referencing table whose corresponding row
is in the detached partition. Which is bogus: once the detach operation
completes, the row becomes an orphan.
However, the code was not doing that in repeatable-read transactions,
because relcache kept a copy of the partition descriptor that included
the partition, and used it in the RI query. This commit changes the
partdesc cache code to only keep descriptors that aren't dependent on
a snapshot (namely: those where no detached partition exist, and those
where detached partitions are included). When a partdesc-without-
detached-partitions is requested, we create one afresh each time; also,
those partdescs are stored in PortalContext instead of
CacheMemoryContext.
find_inheritance_children gets a new output *detached_exist boolean,
which indicates whether any partition marked pending-detach is found.
Its "include_detached" input flag is changed to "omit_detached", because
that name captures desired the semantics more naturally.
CreatePartitionDirectory() and RelationGetPartitionDesc() arguments are
identically renamed.
This was noticed because a buildfarm member that runs with relcache
clobbering, which would not keep the improperly cached partdesc, broke
one test, which led us to realize that the expected output of that test
was bogus. This commit also corrects that expected output.
Author: Amit Langote <amitlangote09@gmail.com>
Author: Álvaro Herrera <alvherre@alvh.no-ip.org>
Discussion: https://postgr.es/m/3269784.1617215412@sss.pgh.pa.us
A new PostgresVersion object type is created and this is used in
PostgresNode using the output of `pg_config --version` and the result
stored in the PostgresNode object. This object can be compared to other
PostgresVersion objects, or to a number or string.
PostgresNode is currently believed to be compatible with versions down
to release 12, so PostgresNode will issue a warning if used with a
version prior to that.
No attempt has been made to deal with incompatibilities in older
versions - that remains work to be undertaken in a subsequent
development cycle.
Based on code from Mark Dilger and Jehan-Guillaume de Rorthais.
Discussion: https://postgr.es/m/a80421c0-3d7e-def1-bcfe-24777f15e344@dunslane.net
On ALTER TABLE .. DETACH CONCURRENTLY, we add a new table constraint
that duplicates the partition constraint. But if the partition already
has another constraint that implies that one, then that's unnecessary.
We were already avoiding the addition of a duplicate constraint if there
was an exact 'equal' match -- this just improves the quality of the check.
Author: Justin Pryzby <pryzby@telsasoft.com>
Reviewed-by: Álvaro Herrera <alvherre@alvh.no-ip.org>
Discussion: https://postgr.es/m/20210410184226.GY6592@telsasoft.com
Previously, it was pg_stat_activity.queryid to match the
pg_stat_statements queryid column. This is an adjustment to patch
4f0b0966c8. This also adjusts some of the internal function calls to
match. Catversion bumped.
Reported-by: Álvaro Herrera, Julien Rouhaud
Discussion: https://postgr.es/m/20210408032704.GA7498@alvherre.pgsql
An oversight introduced by the incremental-sort patches caused
"could not find pathkey item to sort" errors in some situations
where a sort key involves an aggregate or window function.
The basic problem here is that find_em_expr_usable_for_sorting_rel
isn't properly modeling what prepare_sort_from_pathkeys will do
later. Rather than hoping we can keep those functions in sync,
let's refactor so that they actually share the code for
identifying a suitable sort expression.
With this refactoring, tlist.c's tlist_member_ignore_relabel
is unused. I removed it in HEAD but left it in place in v13,
in case any extensions are using it.
Per report from Luc Vlaming. Back-patch to v13 where the
problem arose.
James Coleman and Tom Lane
Discussion: https://postgr.es/m/91f3ec99-85a4-fa55-ea74-33f85a5c651f@swarm64.com
Commit b34ca595ab provided for installation-aware instances of
PostgresNode. However, it turns out that IPC::Run works against this by
caching the path to a binary and not consulting the path again, even if
it has changed. We work around this by calling Postgres binaries with
the installed path rather than just a bare name to be looked up in the
environment path, if there is an installed path. For the common case
where there is no installed path we continue to use the bare command
name.
Diagnosis and solution from Mark Dilger
Discussion: https://postgr.es/m/E8F512F8-B4D6-4514-BA8D-2E671439DA92@enterprisedb.com
As it stands, find_expr_references_walker() pays attention to leaf-node
collation fields while ignoring the input collations of actual function
and operator nodes. That seems exactly backwards from a semantic
standpoint, and it leads to reporting dependencies on collations that
really have nothing to do with the expression's behavior.
Hence, rewrite to look at function input collations instead. This
isn't completely perfect either; it fails to account for the behavior
of record_eq and its siblings. (The previous coding at least gave an
approximation of that, though I think it could be fooled pretty easily
into considering the columns of irrelevant composite types.) We may
be able to improve on this later, but for now this should satisfy the
buildfarm members that didn't like ef387bed8.
In passing fix some oversights in GetTypeCollations(), and get
rid of its duplicative de-duplications. (I'm worried that it's
still potentially O(N^2) or worse, but this makes it a little
better.)
Discussion: https://postgr.es/m/3564817.1618420687@sss.pgh.pa.us
In order to avoid getting old logfile contents certain functions in
PostgresNode were doing one of two things. On Windows it rotated the
logfile and restarted the server, while elsewhere it truncated the log
file. Both of these are unnecessary. We borrow from the buildfarm which
does this instead: note the size of the logfile before we start, and
then when fetching the logfile skip to that position before accumulating
contents. This is spelled differently on Windows but the effect is the
same. This is largely centralized in TestLib's slurp_file function,
which has a new optional parameter, the offset to skip to before
starting to reading the file. Code in the client becomes much neater.
Backpatch to all live branches.
Michael Paquier, slightly modified by me.
Discussion: https://postgr.es/m/YHajnhcMAI3++pJL@paquier.xyz
recordMultipleDependencies had the wrong scope for its "version"
variable, allowing a version label to leak from the collation entry it
was meant for to subsequent non-collation entries. This is relatively
hard to trigger because of the OID-descending order that the inputs
will normally arrive in: subsequent non-collation items will tend to
be pinned. But it can be exhibited easily with a custom collation.
Also, don't special-case the default collation, but instead ignore
pinned-ness of a collation when we've found a version for it. This
avoids creating useless pg_depend entries, and removes a not-very-
future-proof assumption that C, POSIX, and DEFAULT are the only
pinned collations.
A small problem is that, because the default collation may or may
not have a version, the regression tests can't assume anything about
whether dependency entries will be made for it. This seems OK though
since it's now handled just the same as other collations, and we have
test cases for both versioned and unversioned collations.
Fixes oversights in commit 257836a75. Thanks to Julien Rouhaud
for review.
Discussion: https://postgr.es/m/3564817.1618420687@sss.pgh.pa.us
This adds the statistics about total transactions count and total
transaction data logically sent to the decoding output plugin from
ReorderBuffer. Users can query the pg_stat_replication_slots view to check
these stats.
Suggested-by: Andres Freund
Author: Vignesh C and Amit Kapila
Reviewed-by: Sawada Masahiko, Amit Kapila
Discussion: https://postgr.es/m/20210319185247.ldebgpdaxsowiflw@alap3.anarazel.de
Commit e717a9a18 changed the longstanding rule that prosrc is NOT NULL
because when a SQL-language function is written in SQL-standard style,
we don't currently have anything useful to put there. This seems a poor
decision though, as it could easily have negative impacts on external
PLs (opening them to crashes they didn't use to have, for instance).
SQL-function-related code can just as easily test "is prosqlbody not
null" as "is prosrc null", so there's no real gain there either.
Hence, revert the NOT NULL marking removal and adjust related logic.
For now, we just put an empty string into prosrc for SQL-standard
functions. Maybe we'll have a better idea later, although the
history of things like pg_attrdef.adsrc suggests that it's not
easy to maintain a string equivalent of a node tree.
This also adds an assertion that queryDesc->sourceText != NULL
to standard_ExecutorStart. We'd been silently relying on that
for awhile, so let's make it less silent.
Also fix some overlooked documentation and test cases.
Discussion: https://postgr.es/m/2197698.1617984583@sss.pgh.pa.us
These queries could show unexpected entries if the core system,
or concurrently-running test scripts, created any functions that
would appear in the information_schema views. Restrict them
to showing functions belonging to this test's schema, as the
far-older nearby test case does.
Per experimentation with conversion of some built-in functions
to SQL-function-body style.
6568cef, that introduced the option, had an inconsistent behavior when
it comes to configuration tables set up by pg_extension_config_dump, as
the data of all configuration tables would included in a dump even for
extensions not listed by a set of --extension switches.
The contents dumped changed depending on the schema where an extension
was installed when an extension was not listed. For example, an
extension installed under the public schema would have its configuration
data not dumped even when not listed with --extension, which was
inconsistent with the case of an extension installed on a non-public
schema, where the configuration would be dumped.
Per discussion with Noah, we have settled down to the simple rule of
dumping configuration data of an extension if it is listed in
--extension (default is unchanged and backward-compatible, to dump
everything on sight if there are no extensions directly listed). This
avoids some weird cases where the dumps depended on a --schema for one.
More tests are added to cover the gap, where we cross-check more
behaviors depending on --schema when an extension is not listed.
Reported-by: Noah Misch
Reviewed-by: Noah Misch
Discussion: https://postgr.es/m/20210404220802.GA728316@rfd.leadboat.com
Previously you could only use unqualified variable names here.
While that's not a functional deficiency, since only the target
table can be referenced, it's a surprising inconsistency with the
rules for partial-index predicates, on which this syntax is
supposedly modeled.
The fix for that is no harder than passing addToRelNameSpace = true
to addNSItemToQuery. However, it's really pretty bogus for
transformOnConflictArbiter and transformOnConflictClause to be
messing with the namespace item for the target table at all.
It's not theirs to manage, it results in duplicative creations of
namespace items, and transformOnConflictClause wasn't even doing
it quite correctly (that coding resulted in two nsitems for the
target table, since it hadn't cleaned out the existing one).
Hence, make transformInsertStmt responsible for setting up the
target nsitem once for both these clauses and RETURNING.
Also, arrange for ON CONFLICT ... UPDATE's "excluded" pseudo-relation
to be added to the rangetable before we run transformOnConflictArbiter.
This produces a more helpful HINT if someone writes "excluded.col"
in the arbiter expression.
Per bug #16958 from Lukas Eder. Although I agree this is a bug,
the consequences are hardly severe, so no back-patch.
Discussion: https://postgr.es/m/16958-963f638020de271c@postgresql.org
With the Oracle Developer Studio 12.6 compiler, #line directives alter
the current source file location for purposes of #include "..."
directives. Hence, a VPATH build failed with 'cannot find include file:
"specscanner.c"'. With two exceptions, parser-containing directories
already add "-I. -I$(srcdir)"; eliminate the exceptions. Back-patch to
9.6 (all supported versions).
There are hacks in parse_coerce.c to push down a requested coercion
to below any CollateExpr that may appear. However, we did that even
if the requested data type is non-collatable, leading to an invalid
expression tree in which CollateExpr is applied to a non-collatable
type. The fix is just to drop the CollateExpr altogether, reasoning
that it's useless.
This bug is ten years old, dating to the original addition of
COLLATE support. The lack of field complaints suggests that there
aren't a lot of user-visible consequences. We noticed the problem
because it would trigger an assertion in DefineVirtualRelation if
the invalid structure appears as an output column of a view; however,
in a non-assert build, you don't see a crash just a (subtly incorrect)
complaint about applying collation to a non-collatable type. I found
that by putting the incorrect structure further down in a view, I could
make a view definition that would fail dump/reload, per the added
regression test case. But CollateExpr doesn't do anything at run-time,
so this likely doesn't lead to any really exciting consequences.
Per report from Yulin Pei. Back-patch to all supported branches.
Discussion: https://postgr.es/m/HK0PR01MB22744393C474D503E16C8509F4709@HK0PR01MB2274.apcprd01.prod.exchangelabs.com
Using Roman numbers (via "RM" or "rm") for a conversion to calculate a
number of months has never considered the case of negative numbers,
where a conversion could easily cause out-of-bound memory accesses. The
conversions in themselves were not completely consistent either, as
specifying 12 would result in NULL, but it should mean XII.
This commit reworks the conversion calculation to have a more
consistent behavior:
- If the number of months and years is 0, return NULL.
- If the number of months is positive, return the exact month number.
- If the number of months is negative, do a backward calculation, with
-1 meaning December, -2 November, etc.
Reported-by: Theodor Arsenij Larionov-Trichkin
Author: Julien Rouhaud
Discussion: https://postgr.es/m/16953-f255a18f8c51f1d5@postgresql.org
backpatch-through: 9.6
A (relatively minor) annoyance of ErrorResponse/NoticeResponse messages
as printed by PQtrace() is that their length might vary when we move
error messages from one source file to another, one function to another,
or even when their location line numbers change number of digits.
To avoid having to adjust expected files for some tests, make the
regress mode of PQtrace() suppress the length word of NoticeResponse and
ErrorResponse messages.
Discussion: https://postgr.es/m/20210402023010.GA13563@alvherre.pgsql
Reviewed-by: Tom Lane <tgl@sss.pgh.pa.us>
This commit introduces new foreign data wrapper API for TRUNCATE.
It extends TRUNCATE command so that it accepts foreign tables as
the targets to truncate and invokes that API. Also it extends postgres_fdw
so that it can issue TRUNCATE command to foreign servers, by adding
new routine for that TRUNCATE API.
The information about options specified in TRUNCATE command, e.g.,
ONLY, CACADE, etc is passed to FDW via API. The list of foreign tables to
truncate is also passed to FDW. FDW truncates the foreign data sources
that the passed foreign tables specify, based on those information.
For example, postgres_fdw constructs TRUNCATE command using them
and issues it to the foreign server.
For performance, TRUNCATE command invokes the FDW routine for
TRUNCATE once per foreign server that foreign tables to truncate belong to.
Author: Kazutaka Onishi, Kohei KaiGai, slightly modified by Fujii Masao
Reviewed-by: Bharath Rupireddy, Michael Paquier, Zhihong Yu, Alvaro Herrera, Stephen Frost, Ashutosh Bapat, Amit Langote, Daniel Gustafsson, Ibrar Ahmed, Fujii Masao
Discussion: https://postgr.es/m/CAOP8fzb_gkReLput7OvOK+8NHgw-RKqNv59vem7=524krQTcWA@mail.gmail.com
Discussion: https://postgr.es/m/CAJuF6cMWDDqU-vn_knZgma+2GMaout68YUgn1uyDnexRhqqM5Q@mail.gmail.com
ScalarArrayOpExprs with "useOr=true" and a set of Consts on the righthand
side have traditionally been evaluated by using a linear search over the
array. When these arrays contain large numbers of elements then this
linear search could become a significant part of execution time.
Here we add a new method of evaluating ScalarArrayOpExpr expressions to
allow them to be evaluated by first building a hash table containing each
element, then on subsequent evaluations, we just probe that hash table to
determine if there is a match.
The planner is in charge of determining when this optimization is possible
and it enables it by setting hashfuncid in the ScalarArrayOpExpr. The
executor will only perform the hash table evaluation when the hashfuncid
is set.
This means that not all cases are optimized. For example CHECK constraints
containing an IN clause won't go through the planner, so won't get the
hashfuncid set. We could maybe do something about that at some later
date. The reason we're not doing it now is from fear that we may slow
down cases where the expression is evaluated only once. Those cases can
be common, for example, a single row INSERT to a table with a CHECK
constraint containing an IN clause.
In the planner, we enable this when there are suitable hash functions for
the ScalarArrayOpExpr's operator and only when there is at least
MIN_ARRAY_SIZE_FOR_HASHED_SAOP elements in the array. The threshold is
currently set to 9.
Author: James Coleman, David Rowley
Reviewed-by: David Rowley, Tomas Vondra, Heikki Linnakangas
Discussion: https://postgr.es/m/CAAaqYe8x62+=wn0zvNKCj55tPpg-JBHzhZFFc6ANovdqFw7-dA@mail.gmail.com
Introduce a new GUC recovery_prefetch, disabled by default. When
enabled, look ahead in the WAL and try to initiate asynchronous reading
of referenced data blocks that are not yet cached in our buffer pool.
For now, this is done with posix_fadvise(), which has several caveats.
Better mechanisms will follow in later work on the I/O subsystem.
The GUC maintenance_io_concurrency is used to limit the number of
concurrent I/Os we allow ourselves to initiate, based on pessimistic
heuristics used to infer that I/Os have begun and completed.
The GUC wal_decode_buffer_size is used to limit the maximum distance we
are prepared to read ahead in the WAL to find uncached blocks.
Reviewed-by: Alvaro Herrera <alvherre@2ndquadrant.com> (parts)
Reviewed-by: Andres Freund <andres@anarazel.de> (parts)
Reviewed-by: Tomas Vondra <tomas.vondra@2ndquadrant.com> (parts)
Tested-by: Tomas Vondra <tomas.vondra@2ndquadrant.com>
Tested-by: Jakub Wartak <Jakub.Wartak@tomtom.com>
Tested-by: Dmitry Dolgov <9erthalion6@gmail.com>
Tested-by: Sait Talha Nisanci <Sait.Nisanci@microsoft.com>
Discussion: https://postgr.es/m/CA%2BhUKGJ4VJN8ttxScUFM8dOKX0BrBiboo5uz1cq%3DAovOddfHpA%40mail.gmail.com
Previously, autovacuum would completely ignore partitioned tables, which
is not good regarding analyze -- failing to analyze those tables means
poor plans may be chosen. Make autovacuum aware of those tables by
propagating "changes since analyze" counts from the leaf partitions up
the partitioning hierarchy.
This also introduces necessary reloptions support for partitioned tables
(autovacuum_enabled, autovacuum_analyze_scale_factor,
autovacuum_analyze_threshold). It's unclear how best to document this
aspect.
Author: Yuzuko Hosoya <yuzukohosoya@gmail.com>
Reviewed-by: Kyotaro Horiguchi <horikyota.ntt@gmail.com>
Reviewed-by: Tomas Vondra <tomas.vondra@enterprisedb.com>
Reviewed-by: Álvaro Herrera <alvherre@alvh.no-ip.org>
Discussion: https://postgr.es/m/CAKkQ508_PwVgwJyBY=0Lmkz90j8CmWNPUxgHvCUwGhMrouz6UA@mail.gmail.com
When dealing with overloaded function or operator names, having
to look through a long list of matches is tedious. Let's extend
these commands to allow specification of (input) argument types
to let such results be trimmed down. Each additional argument
is treated the same as the pattern argument of \dT and matched
against the appropriate argument's type name.
While at it, fix \dT (and these new options) to recognize the
usual notation of "foo[]" for "the array type over foo", and
to handle the special abbreviations allowed by the backend
grammar, such as "int" for "integer".
Greg Sabino Mullane, revised rather significantly by me
Discussion: https://postgr.es/m/CAKAnmmLF9Hhu02N+s7uAyLc5J1xZReg72HQUoiKhNiJV3_jACQ@mail.gmail.com
The truncation of the log file, that this set of tests relies on to make
sure that a connection attempt matches with its expected backend log
pattern, fails, as reported by buildfarm member fairywren. Instead of a
truncation, do a rotation of the log file and restart the node. This
will ensure that the connection attempt data is unique for each test.
Discussion: https://postgr.es/m/YG05nCI8x8B+Ad3G@paquier.xyz
This adds support for writing CREATE FUNCTION and CREATE PROCEDURE
statements for language SQL with a function body that conforms to the
SQL standard and is portable to other implementations.
Instead of the PostgreSQL-specific AS $$ string literal $$ syntax,
this allows writing out the SQL statements making up the body
unquoted, either as a single statement:
CREATE FUNCTION add(a integer, b integer) RETURNS integer
LANGUAGE SQL
RETURN a + b;
or as a block
CREATE PROCEDURE insert_data(a integer, b integer)
LANGUAGE SQL
BEGIN ATOMIC
INSERT INTO tbl VALUES (a);
INSERT INTO tbl VALUES (b);
END;
The function body is parsed at function definition time and stored as
expression nodes in a new pg_proc column prosqlbody. So at run time,
no further parsing is required.
However, this form does not support polymorphic arguments, because
there is no more parse analysis done at call time.
Dependencies between the function and the objects it uses are fully
tracked.
A new RETURN statement is introduced. This can only be used inside
function bodies. Internally, it is treated much like a SELECT
statement.
psql needs some new intelligence to keep track of function body
boundaries so that it doesn't send off statements when it sees
semicolons that are inside a function body.
Tested-by: Jaime Casanova <jcasanov@systemguards.com.ec>
Reviewed-by: Julien Rouhaud <rjuju123@gmail.com>
Discussion: https://www.postgresql.org/message-id/flat/1c11f1eb-f00c-43b7-799d-2d44132c02d7@2ndquadrant.com
Use the in-core query id computation for pg_stat_activity,
log_line_prefix, and EXPLAIN VERBOSE.
Similar to other fields in pg_stat_activity, only the queryid from the
top level statements are exposed, and if the backends status isn't
active then the queryid from the last executed statements is displayed.
Add a %Q placeholder to include the queryid in log_line_prefix, which
will also only expose top level statements.
For EXPLAIN VERBOSE, if a query identifier has been computed, either by
enabling compute_query_id or using a third-party module, display it.
Bump catalog version.
Discussion: https://postgr.es/m/20210407125726.tkvjdbw76hxnpwfi@nol
Author: Julien Rouhaud
Reviewed-by: Alvaro Herrera, Nitin Jadhav, Zhihong Yu
Formerly we were pretty lax about what a custom GUC's name could
be; so long as it had at least one dot in it, we'd take it.
However, corner cases such as dashes or equal signs in the name
would cause various bits of functionality to misbehave. Rather
than trying to make the world perfectly safe for that, let's
just require that custom names look like "identifier.identifier",
where "identifier" means something that scan.l would accept
without double quotes.
Along the way, this patch refactors things slightly in guc.c
so that find_option() is responsible for reporting GUC-not-found
cases, allowing removal of duplicative code from its callers.
Per report from Hubert Depesz Lubaczewski. No back-patch,
since the consequences of the problem don't seem to warrant
changing behavior in stable branches.
Discussion: https://postgr.es/m/951335.1612910077@sss.pgh.pa.us
Documentation and comments in code and tests have been using the terms
sensitive/insensitive cursor incorrectly relative to the SQL standard.
(Cursor sensitivity is only relevant for changes made in the same
transaction as the cursor, not for concurrent changes in other
sessions.) Moreover, some of the behavior of PostgreSQL is incorrect
according to the SQL standard, confusing the issue further. (WHERE
CURRENT OF changes are not visible in insensitive cursors, but they
should be.)
This change corrects the terminology and removes the claim that
sensitive cursors are supported. It also adds a test case that checks
the insensitive behavior in a "correct" way, using a change command
not using WHERE CURRENT OF. Finally, it adds the ASENSITIVE cursor
option to select the default asensitive behavior, per SQL standard.
There are no changes to cursor behavior in this patch.
Discussion: https://www.postgresql.org/message-id/flat/96ee8b30-9889-9e1b-b053-90e10c050e85%40enterprisedb.com
The "authenticated identity" is the string used by an authentication
method to identify a particular user. In many common cases, this is the
same as the PostgreSQL username, but for some third-party authentication
methods, the identifier in use may be shortened or otherwise translated
(e.g. through pg_ident user mappings) before the server stores it.
To help administrators see who has actually interacted with the system,
this commit adds the capability to store the original identity when
authentication succeeds within the backend's Port, and generates a log
entry when log_connections is enabled. The log entries generated look
something like this (where a local user named "foouser" is connecting to
the database as the database user called "admin"):
LOG: connection received: host=[local]
LOG: connection authenticated: identity="foouser" method=peer (/data/pg_hba.conf:88)
LOG: connection authorized: user=admin database=postgres application_name=psql
Port->authn_id is set according to the authentication method:
bsd: the PostgreSQL username (aka the local username)
cert: the client's Subject DN
gss: the user principal
ident: the remote username
ldap: the final bind DN
pam: the PostgreSQL username (aka PAM username)
password (and all pw-challenge methods): the PostgreSQL username
peer: the peer's pw_name
radius: the PostgreSQL username (aka the RADIUS username)
sspi: either the down-level (SAM-compatible) logon name, if
compat_realm=1, or the User Principal Name if compat_realm=0
The trust auth method does not set an authenticated identity. Neither
does clientcert=verify-full.
Port->authn_id could be used for other purposes, like a superuser-only
extra column in pg_stat_activity, but this is left as future work.
PostgresNode::connect_{ok,fails}() have been modified to let tests check
the backend log files for required or prohibited patterns, using the
new log_like and log_unlike parameters. This uses a method based on a
truncation of the existing server log file, like issues_sql_like().
Tests are added to the ldap, kerberos, authentication and SSL test
suites.
Author: Jacob Champion
Reviewed-by: Stephen Frost, Magnus Hagander, Tom Lane, Michael Paquier
Discussion: https://postgr.es/m/c55788dd1773c521c862e8e0dddb367df51222be.camel@vmware.com
The buildfarm members "drongo" and "fairywren" reported that
the regression test (024_archive_recovery.pl) added by commit 9de9294b0c
failed. The cause of this failure is that the test calls $node->init()
without "allows_streaming => 1" and which doesn't add pg_hba.conf
entry for TCP/IP connection from pg_basebackup.
This commit fixes the issue by specifying "allows_streaming => 1"
when calling $node->init().
Author: Fujii Masao
Discussion: https://postgr.es/m/3cc3909d-f779-7a74-c201-f1f7f62c7497@oss.nttdata.com
DEBUG was already defined by the MSVC toolchain for "Debug" builds. On
these systems the unconditional #define DEBUG was causing a 'DEBUG': macro
redefinition warning.
Here we rename DEBUG to DEBUG_OUPUT and also get rid of the #define which
defined this constant. This appears to have been left in the code by
mistake.
Discussion: https://postgr.es/m/CAApHDvqTTgDm38s4HRj03nhzhzQ1oMOj-RXFUB1pE6Bj07jyuQ@mail.gmail.com
Arrange to do some things on-demand, rather than immediately during
executor startup, because there's a fair chance of never having to do
them at all:
* Don't open result relations' indexes until needed.
* Don't initialize partition tuple routing, nor the child-to-root
tuple conversion map, until needed.
This wins in UPDATEs on partitioned tables when only some of the
partitions will actually receive updates; with larger partition
counts the savings is quite noticeable. Also, we can remove some
sketchy heuristics in ExecInitModifyTable about whether to set up
tuple routing.
Also, remove execPartition.c's private hash table tracking which
partitions were already opened by the ModifyTable node. Instead
use the hash added to ModifyTable itself by commit 86dc90056.
To allow lazy computation of the conversion maps, we now set
ri_RootResultRelInfo in all child ResultRelInfos. We formerly set it
only in some, not terribly well-defined, cases. This has user-visible
side effects in that now more error messages refer to the root
relation instead of some partition (and provide error data in the
root's column order, too). It looks to me like this is a strict
improvement in consistency, so I don't have a problem with the
output changes visible in this commit.
Extracted from a larger patch, which seemed to me to be too messy
to push in one commit.
Amit Langote, reviewed at different times by Heikki Linnakangas and
myself
Discussion: https://postgr.es/m/CA+HiwqG7ZruBmmih3wPsBZ4s0H2EhywrnXEduckY5Hr3fWzPWA@mail.gmail.com
Snapshot caching, introduced in 623a9ba79b, did not increment
xactCompletionCount during subtransaction abort. That could lead to an older
snapshot being reused. That is, at least as far as I can see, not a
correctness issue (for MVCC snapshots there's no difference between "in
progress" and "aborted"). The only difference between the old and new
snapshots would be a newer ->xmax.
While HeapTupleSatisfiesMVCC makes the same visibility determination, reusing
the old snapshot leads HeapTupleSatisfiesMVCC to not set
HEAP_XMIN_INVALID. Which subsequently causes the kill_prior_tuple optimization
to not kick in (via HeapTupleIsSurelyDead() returning false). The performance
effects of doing the same index-lookups over and over again is how the issue
was discovered...
Fix the issue by incrementing xactCompletionCount in
XidCacheRemoveRunningXids. It already acquires ProcArrayLock exclusively,
making that an easy proposition.
Add a test to ensure that kill_prior_tuple prevents index growth when it
involves aborted subtransaction of the current transaction.
Author: Andres Freund
Discussion: https://postgr.es/m/20210406043521.lopeo7bbigad3n6t@alap3.anarazel.de
Discussion: https://postgr.es/m/20210317055718.v6qs3ltzrformqoa%40alap3.anarazel.de
Previously, psql printed only the last result if a command string
returned multiple result sets. Now it prints all of them. The
previous behavior can be obtained by setting the psql variable
SHOW_ALL_RESULTS to off.
Author: Fabien COELHO <coelho@cri.ensmp.fr>
Reviewed-by: "Iwata, Aya" <iwata.aya@jp.fujitsu.com>
Reviewed-by: Daniel Verite <daniel@manitou-mail.org>
Reviewed-by: Peter Eisentraut <peter.eisentraut@2ndquadrant.com>
Reviewed-by: Kyotaro Horiguchi <horikyota.ntt@gmail.com>
Reviewed-by: vignesh C <vignesh21@gmail.com>
Discussion: https://www.postgresql.org/message-id/flat/alpine.DEB.2.21.1904132231510.8961@lancre
Handling of incompatible clauses while applying extended statistics was
a bit confused - while handling a mix of compatible and incompatible
clauses it sometimes incorrectly treated the incompatible clauses as
compatible, resulting in a crash.
Fixed by reworking the code applying the selected statistics object to
make it easier to understand, and adding a proper compatibility check.
Reported-by: David Rowley
Discussion: https://postgr.es/m/CAApHDvpYT10-nkSp8xXe-nbO3jmoaRyRFHbzh-RWMfAJynqgpQ%40mail.gmail.com
Previously if hot standby was enabled, archive recovery exited with
an error when it found WAL generated with wal_level=minimal.
But if hot standby was disabled, it just reported a warning and
continued in that case. Which could lead to data loss or errors
during normal operation. A warning was emitted, but users could
easily miss that and not notice this serious situation until
they encountered the actual errors.
To improve this situation, this commit changes archive recovery
so that it exits with FATAL error when it finds WAL generated with
wal_level=minimal whatever the setting of hot standby. This enables
users to notice the serious situation soon.
The FATAL error is thrown if archive recovery starts from a base
backup taken before wal_level is changed to minimal. When archive
recovery exits with the error, if users have a base backup taken
after setting wal_level to higher than minimal, they can recover
the database by starting archive recovery from that newer backup.
But note that if such backup doesn't exist, there is no easy way to
complete archive recovery, which may make the database server
unstartable and users may lose whole database. The commit adds
the note about this risk into the document.
Even in the case of unstartable database server, previously by just
disabling hot standby users could avoid the error during archive
recovery, forcibly start up the server and salvage data from it.
But note that this commit makes this procedure unavailable at all.
Author: Takamichi Osumi
Reviewed-by: Laurenz Albe, Kyotaro Horiguchi, David Steele, Fujii Masao
Discussion: https://postgr.es/m/OSBPR01MB4888CBE1DA08818FD2D90ED8EDF90@OSBPR01MB4888.jpnprd01.prod.outlook.com
At present, if we want to update publications in a subscription, we
can use SET PUBLICATION. However, it requires supplying all
publications that exists and the new publications. If we want to add
new publications, it's inconvenient. The new syntax only supplies the
new publications. When the refresh is true, it only refreshes the new
publications.
Author: Japin Li <japinli@hotmail.com>
Author: Bharath Rupireddy <bharath.rupireddyforpostgres@gmail.com>
Discussion: https://www.postgresql.org/message-id/flat/MEYP282MB166939D0D6C480B7FBE7EFFBB6BC0@MEYP282MB1669.AUSP282.PROD.OUTLOOK.COM
In the tests, after disabling the subscription, we were not waiting for
the replication connection to drop from the publisher. So when the test
was trying to use the same slot to fetch the messages via SQL API, it
sometimes gives an error that the replication slot is active for other
PID.
Per buildfarm.
The previous implementation of EXTRACT mapped internally to
date_part(), which returned type double precision (since it was
implemented long before the numeric type existed). This can lead to
imprecise output in some cases, so returning numeric would be
preferrable. Changing the return type of an existing function is a
bit risky, so instead we do the following: We implement a new set of
functions, which are now called "extract", in parallel to the existing
date_part functions. They work the same way internally but use
numeric instead of float8. The EXTRACT construct is now mapped by the
parser to these new extract functions. That way, dumps of views
etc. from old versions (which would use date_part) continue to work
unchanged, but new uses will map to the new extract functions.
Additionally, the reverse compilation of EXTRACT now reproduces the
original syntax, using the new mechanism introduced in
40c24bfef9.
The following minor changes of behavior result from the new
implementation:
- The column name from an isolated EXTRACT call is now "extract"
instead of "date_part".
- Extract from date now rejects inappropriate field names such as
HOUR. It was previously mapped internally to extract from
timestamp, so it would silently accept everything appropriate for
timestamp.
- Return values when extracting fields with possibly fractional
values, such as second and epoch, now have the full scale that the
value has internally (so, for example, '1.000000' instead of just
'1').
Reported-by: Petr Fedorov <petr.fedorov@phystech.edu>
Reviewed-by: Tom Lane <tgl@sss.pgh.pa.us>
Discussion: https://www.postgresql.org/message-id/flat/42b73d2d-da12-ba9f-570a-420e0cce19d9@phystech.edu
Commit 3e98c0bafb added pg_backend_memory_contexts view to display
the memory contexts of the backend process. However its target process
is limited to the backend that is accessing to the view. So this is
not so convenient when investigating the local memory bloat of other
backend process. To improve this situation, this commit adds
pg_log_backend_memory_contexts() function that requests to log
the memory contexts of the specified backend process.
This information can be also collected by calling
MemoryContextStats(TopMemoryContext) via a debugger. But
this technique cannot be used in some environments because no debugger
is available there. So, pg_log_backend_memory_contexts() allows us to
see the memory contexts of specified backend more easily.
Only superusers are allowed to request to log the memory contexts
because allowing any users to issue this request at an unbounded rate
would cause lots of log messages and which can lead to denial of service.
On receipt of the request, at the next CHECK_FOR_INTERRUPTS(),
the target backend logs its memory contexts at LOG_SERVER_ONLY level,
so that these memory contexts will appear in the server log but not
be sent to the client. It logs one message per memory context.
Because if it buffers all memory contexts into StringInfo to log them
as one message, which may require the buffer to be enlarged very much
and lead to OOM error since there can be a large number of memory
contexts in a backend.
When a backend process is consuming huge memory, logging all its
memory contexts might overrun available disk space. To prevent this,
now this patch limits the number of child contexts to log per parent
to 100. As with MemoryContextStats(), it supposes that practical cases
where the log gets long will typically be huge numbers of siblings
under the same parent context; while the additional debugging value
from seeing details about individual siblings beyond 100 will not be large.
There was another proposed patch to add the function to return
the memory contexts of specified backend as the result sets,
instead of logging them, in the discussion. However that patch is
not included in this commit because it had several issues to address.
Thanks to Tatsuhito Kasahara, Andres Freund, Tom Lane, Tomas Vondra,
Michael Paquier, Kyotaro Horiguchi and Zhihong Yu for the discussion.
Bump catalog version.
Author: Atsushi Torikoshi
Reviewed-by: Kyotaro Horiguchi, Zhihong Yu, Fujii Masao
Discussion: https://postgr.es/m/0271f440ac77f2a4180e0e56ebd944d1@oss.nttdata.com
The recent refactoring done in c50624c accidentally broke a portion of
the kerberos tests checking after a query, so add its functionality
back. Some inactive SSL tests had their arguments in an incorrect
order, which would cause them to fail if they were to run.
Author: Jacob Champion
Discussion: https://postgr.es/m/4f5b0b3dc0b6fe9ae6a34886b4d4000f61eb567e.camel@vmware.com
The output plugin accepts a new parameter (messages) that controls if
logical decoding messages are written into the replication stream. It is
useful for those clients that use pgoutput as an output plugin and needs
to process messages that were written by pg_logical_emit_message().
Although logical streaming replication protocol supports logical
decoding messages now, logical replication does not use this feature yet.
Author: David Pirotte, Euler Taveira
Reviewed-by: Euler Taveira, Andres Freund, Ashutosh Bapat, Amit Kapila
Discussion: https://postgr.es/m/CADK3HHJ-+9SO7KuRLH=9Wa1rAo60Yreq1GFNkH_kd0=CdaWM+A@mail.gmail.com
This type of failure is similar to what has been fixed in c757a3da,
where an authentication failure combined with psql pushing a command
down its communication pipe causes a test failure. This routine is
designed to fail, so sending a query has little sense anyway.
Per buildfarm members gaur and hoverfly, based on an analysis and fix
from Tom Lane.
Discussion: https://postgr.es/m/513200.1617634642@sss.pgh.pa.us
Not much to say here: does what it says on the tin.
We steal a previously-always-zero bit from the nextOffset
field of leaf index tuples in order to track whether there
is a nulls bitmap. Otherwise it works about like included
columns in other index types.
Pavel Borisov, reviewed by Andrey Borodin and Anastasia Lubennikova,
and rather heavily editorialized on by me
Discussion: https://postgr.es/m/CALT9ZEFi-vMp4faht9f9Junb1nO3NOSjhpxTmbm1UGLMsLqiEQ@mail.gmail.com
A commonly requested use-case is to have a role who can run an
unfettered pg_dump without having to explicitly GRANT that user access
to all tables, schemas, et al, without that role being a superuser.
This address that by adding a "pg_read_all_data" role which implicitly
gives any member of this role SELECT rights on all tables, views and
sequences, and USAGE rights on all schemas.
As there may be cases where it's also useful to have a role who has
write access to all objects, pg_write_all_data is also introduced and
gives users implicit INSERT, UPDATE and DELETE rights on all tables,
views and sequences.
These roles can not be logged into directly but instead should be
GRANT'd to a role which is able to log in. As noted in the
documentation, if RLS is being used then an administrator may (or may
not) wish to set BYPASSRLS on the login role which these predefined
roles are GRANT'd to.
Reviewed-by: Georgios Kokolatos
Discussion: https://postgr.es/m/20200828003023.GU29590@tamriel.snowman.net
This commit refactors more TAP tests to adapt with the recent
introduction of connect_ok() and connect_fails() in PostgresNode,
introduced by 0d1a3343. This changes the following test suites to use
the same code paths for connection checks:
- Kerberos
- LDAP
- SSL
- Authentication
Those routines are extended to be able to handle optional parameters
that are set depending on each suite's needs, as of:
- custom SQL query.
- expected stderr matching pattern.
- expected stdout matching pattern.
The new design is extensible with more parameters, and there are some
plans for those routines in the future with checks based on the contents
of the backend logs.
Author: Jacob Champion, Michael Paquier
Discussion: https://postgr.es/m/d17b919e27474abfa55d97786cb9cfadfe2b59e9.camel@vmware.com
According to the documentation, the attType passed to the opclass
config function (and also relied on by the core code) is the type
of the heap column or expression being indexed. But what was
actually being passed was the type stored for the index column.
This made no difference for user-defined SP-GiST opclasses,
because we weren't allowing the STORAGE clause of CREATE OPCLASS
to be used, so the two types would be the same. But it's silly
not to allow that, seeing that the built-in poly_ops opclass
has a different value for opckeytype than opcintype, and that if you
want to do lossy storage then the types must really be different.
(Thus, user-defined opclasses doing lossy storage had to lie about
what type is in the index.) Hence, remove the restriction, and make
sure that we use the input column type not opckeytype where relevant.
For reasons of backwards compatibility with existing user-defined
opclasses, we can't quite insist that the specified leafType match
the STORAGE clause; instead just add an amvalidate() warning if
they don't match.
Also fix some bugs that would only manifest when trying to return
index entries when attType is different from attLeafType. It's not
too surprising that these have not been reported, because the only
usual reason for such a difference is to store the leaf value
lossily, rendering index-only scans impossible.
Add a src/test/modules module to exercise cases where attType is
different from attLeafType and yet index-only scan is supported.
Discussion: https://postgr.es/m/3728741.1617381471@sss.pgh.pa.us
The TAP tests of src/test/ssl/ have been using rather generic matching
patterns to check some failure scenarios, like "SSL error" or just
"FATAL". These have been introduced in 081bfc1.
Those messages are not wrong per se, but when working on the integration
of new SSL libraries it becomes hard to know if those errors are legit
or not, and existing scenarios may fail in incorrect ways. This commit
makes all those messages more verbose by adding the information
generated by OpenSSL. Fortunately, the same error messages are used for
all the versions supported on HEAD (checked that after running the tests
from 1.0.1 to 1.1.1), so the change is straight-forward.
Reported-by: Jacob Champion, Álvaro Herrera
Discussion: https://postgr.es/m/YGU3AxQh0zBMMW8m@paquier.xyz
force_parallel_mode = regress is causing a few more problems than I
thought. It seems that both the leader and the single worker can
contribute to the execution. I had mistakenly thought that only the worker
process would do any work. Since it's not deterministic as to which
of the two processes will get a chance to work on the plan, it seems just
better to disable force_parallel_mode for these tests. At least doing
this seems better than changing to EXPLAIN only rather than EXPLAIN
ANALYZE.
Additionally, I overlooked the fact that the number of executions of the
sub-plan below a Result Cache will execute a varying number of times
depending on cache eviction. 32-bit machines will use less memory and
evict fewer tuples from the cache. That results in the subnode being
executed fewer times on 32-bit machines. Let's just blank out the number
of loops in each node.
Here we add a new executor node type named "Result Cache". The planner
can include this node type in the plan to have the executor cache the
results from the inner side of parameterized nested loop joins. This
allows caching of tuples for sets of parameters so that in the event that
the node sees the same parameter values again, it can just return the
cached tuples instead of rescanning the inner side of the join all over
again. Internally, result cache uses a hash table in order to quickly
find tuples that have been previously cached.
For certain data sets, this can significantly improve the performance of
joins. The best cases for using this new node type are for join problems
where a large portion of the tuples from the inner side of the join have
no join partner on the outer side of the join. In such cases, hash join
would have to hash values that are never looked up, thus bloating the hash
table and possibly causing it to multi-batch. Merge joins would have to
skip over all of the unmatched rows. If we use a nested loop join with a
result cache, then we only cache tuples that have at least one join
partner on the outer side of the join. The benefits of using a
parameterized nested loop with a result cache increase when there are
fewer distinct values being looked up and the number of lookups of each
value is large. Also, hash probes to lookup the cache can be much faster
than the hash probe in a hash join as it's common that the result cache's
hash table is much smaller than the hash join's due to result cache only
caching useful tuples rather than all tuples from the inner side of the
join. This variation in hash probe performance is more significant when
the hash join's hash table no longer fits into the CPU's L3 cache, but the
result cache's hash table does. The apparent "random" access of hash
buckets with each hash probe can cause a poor L3 cache hit ratio for large
hash tables. Smaller hash tables generally perform better.
The hash table used for the cache limits itself to not exceeding work_mem
* hash_mem_multiplier in size. We maintain a dlist of keys for this cache
and when we're adding new tuples and realize we've exceeded the memory
budget, we evict cache entries starting with the least recently used ones
until we have enough memory to add the new tuples to the cache.
For parameterized nested loop joins, we now consider using one of these
result cache nodes in between the nested loop node and its inner node. We
determine when this might be useful based on cost, which is primarily
driven off of what the expected cache hit ratio will be. Estimating the
cache hit ratio relies on having good distinct estimates on the nested
loop's parameters.
For now, the planner will only consider using a result cache for
parameterized nested loop joins. This works for both normal joins and
also for LATERAL type joins to subqueries. It is possible to use this new
node for other uses in the future. For example, to cache results from
correlated subqueries. However, that's not done here due to some
difficulties obtaining a distinct estimation on the outer plan to
calculate the estimated cache hit ratio. Currently we plan the inner plan
before planning the outer plan so there is no good way to know if a result
cache would be useful or not since we can't estimate the number of times
the subplan will be called until the outer plan is generated.
The functionality being added here is newly introducing a dependency on
the return value of estimate_num_groups() during the join search.
Previously, during the join search, we only ever needed to perform
selectivity estimations. With this commit, we need to use
estimate_num_groups() in order to estimate what the hit ratio on the
result cache will be. In simple terms, if we expect 10 distinct values
and we expect 1000 outer rows, then we'll estimate the hit ratio to be
99%. Since cache hits are very cheap compared to scanning the underlying
nodes on the inner side of the nested loop join, then this will
significantly reduce the planner's cost for the join. However, it's
fairly easy to see here that things will go bad when estimate_num_groups()
incorrectly returns a value that's significantly lower than the actual
number of distinct values. If this happens then that may cause us to make
use of a nested loop join with a result cache instead of some other join
type, such as a merge or hash join. Our distinct estimations have been
known to be a source of trouble in the past, so the extra reliance on them
here could cause the planner to choose slower plans than it did previous
to having this feature. Distinct estimations are also fairly hard to
estimate accurately when several tables have been joined already or when a
WHERE clause filters out a set of values that are correlated to the
expressions we're estimating the number of distinct value for.
For now, the costing we perform during query planning for result caches
does put quite a bit of faith in the distinct estimations being accurate.
When these are accurate then we should generally see faster execution
times for plans containing a result cache. However, in the real world, we
may find that we need to either change the costings to put less trust in
the distinct estimations being accurate or perhaps even disable this
feature by default. There's always an element of risk when we teach the
query planner to do new tricks that it decides to use that new trick at
the wrong time and causes a regression. Users may opt to get the old
behavior by turning the feature off using the enable_resultcache GUC.
Currently, this is enabled by default. It remains to be seen if we'll
maintain that setting for the release.
Additionally, the name "Result Cache" is the best name I could think of
for this new node at the time I started writing the patch. Nobody seems
to strongly dislike the name. A few people did suggest other names but no
other name seemed to dominate in the brief discussion that there was about
names. Let's allow the beta period to see if the current name pleases
enough people. If there's some consensus on a better name, then we can
change it before the release. Please see the 2nd discussion link below
for the discussion on the "Result Cache" name.
Author: David Rowley
Reviewed-by: Andy Fan, Justin Pryzby, Zhihong Yu, Hou Zhijie
Tested-By: Konstantin Knizhnik
Discussion: https://postgr.es/m/CAApHDvrPcQyQdWERGYWx8J%2B2DLUNgXu%2BfOSbQ1UscxrunyXyrQ%40mail.gmail.com
Discussion: https://postgr.es/m/CAApHDvq=yQXr5kqhRviT2RhNKwToaWr9JAN5t+5_PzhuRJ3wvg@mail.gmail.com
This test has been using a simple VACUUM with pg_relation_size() to
check if a relation gets physically truncated or not, but forgot the
fact that some concurrent activity, like checkpoint buffer writes, could
cause some pages to be skipped. The second test enabling
vacuum_truncate could fail, seeing a non-empty relation. The first test
would not have failed, but could finish by testing a behavior different
than the one aimed for. Both tests gain a FREEZE option, to make the
vacuums more aggressive and prevent page skips.
This is similar to the issues fixed in c2dc1a7.
Author: Arseny Sher
Reviewed-by: Masahiko Sawada
Discussion: https://postgr.es/m/87tuotr2hh.fsf@ars-thinkpad
backpatch-through: 12
Windows doesn't like setvbuf(..., _IOLBF) and crashes if you use it,
which has been causing the libpq_pipeline failures all along ... and our
own port.h has known about it for a long time: it offers PG_IOLBF that's
defined to _IONBF on that platform. Follow its advice.
While at it, get rid of a bogus bitshift that used a constant of the
wrong size. Decorate the constant as LL to fix. While at it, remove a
pointless addition that only confused matters.
All as diagnosed by Tom Lane.
Discussion: https://postgr.es/m/3458958.1617302154@sss.pgh.pa.us
I forgot to strdup() when processing argv[]. Apparently many platforms
hide this mistake from users, but in those that don't you may get a
program crash. Repair.
Per buildfarm member drongo, which is the only one in all the buildfarm
manifesting a problem here.
While at it, move "numrows" processing out of the line of special cases,
and make it getopt's -r instead. (A similar thing could be done to
'conninfo', but current use of the program doesn't warrant spending time
on that -- nowhere else we use conninfo in so simplistic a manner.)
Discussion: https://postgr.es/m/20210401124850.GA19247@alvherre.pgsql
With the 'noError' argument, you can try to convert a buffer without
knowing the character boundaries beforehand. The functions now need to
return the number of input bytes successfully converted.
This is is a backwards-incompatible change, if you have created a custom
encoding conversion with CREATE CONVERSION. This adds a check to
pg_upgrade for that, refusing the upgrade if there are any user-defined
encoding conversions. Custom conversions are very rare, there are no
commonly used extensions that I know of that uses that feature. No other
objects can depend on conversions, so if you do have one, you can fairly
easily drop it before upgrading, and recreate it after the upgrade with
an updated version.
Add regression tests for built-in encoding conversions. This doesn't cover
every conversion, but it covers all the internal functions in conv.c that
are used to implement the conversions.
Reviewed-by: John Naylor
Discussion: https://www.postgresql.org/message-id/e7861509-3960-538a-9025-b75a61188e01%40iki.fi
test_connect_ok() and test_connect_fails() have always been part of the
SSL tests, and check if a connection to the backend should work or not,
and there are sanity checks done on specific error patterns dropped by
libpq if the connection fails.
This was fundamentally wrong on two aspects. First, SSLServer.pm works
mostly on setting up and changing the SSL configuration of a
PostgresNode, and has really nothing to do with the client. Second,
the situation became worse in light of b34ca595, where the SSL tests
would finish by using a psql command that may not come from the same
installation as the node set up.
This commit moves those client routines into PostgresNode, making easier
the refactoring of SSLServer to become more SSL-implementation aware.
This can also be reused by the ldap, kerberos and authentication test
suites for connection checks, and a follow-up patch should extend those
interfaces to match with backend log patterns.
Author: Michael Paquier
Reviewed-by: Andrew Dunstan, Daniel Gustafsson, Álvaro Herrera
Discussion: https://postgr.es/m/YGLKNBf9zyh6+WSt@paquier.xyz
This removes "Add Result Cache executor node". It seems that something
weird is going on with the tracking of cache hits and misses as
highlighted by many buildfarm animals. It's not yet clear what the
problem is as other parts of the plan indicate that the cache did work
correctly, it's just the hits and misses that were being reported as 0.
This is especially a bad time to have the buildfarm so broken, so
reverting before too many more animals go red.
Discussion: https://postgr.es/m/CAApHDvq_hydhfovm4=izgWs+C5HqEeRScjMbOgbpC-jRAeK3Yw@mail.gmail.com
Here we add a new executor node type named "Result Cache". The planner
can include this node type in the plan to have the executor cache the
results from the inner side of parameterized nested loop joins. This
allows caching of tuples for sets of parameters so that in the event that
the node sees the same parameter values again, it can just return the
cached tuples instead of rescanning the inner side of the join all over
again. Internally, result cache uses a hash table in order to quickly
find tuples that have been previously cached.
For certain data sets, this can significantly improve the performance of
joins. The best cases for using this new node type are for join problems
where a large portion of the tuples from the inner side of the join have
no join partner on the outer side of the join. In such cases, hash join
would have to hash values that are never looked up, thus bloating the hash
table and possibly causing it to multi-batch. Merge joins would have to
skip over all of the unmatched rows. If we use a nested loop join with a
result cache, then we only cache tuples that have at least one join
partner on the outer side of the join. The benefits of using a
parameterized nested loop with a result cache increase when there are
fewer distinct values being looked up and the number of lookups of each
value is large. Also, hash probes to lookup the cache can be much faster
than the hash probe in a hash join as it's common that the result cache's
hash table is much smaller than the hash join's due to result cache only
caching useful tuples rather than all tuples from the inner side of the
join. This variation in hash probe performance is more significant when
the hash join's hash table no longer fits into the CPU's L3 cache, but the
result cache's hash table does. The apparent "random" access of hash
buckets with each hash probe can cause a poor L3 cache hit ratio for large
hash tables. Smaller hash tables generally perform better.
The hash table used for the cache limits itself to not exceeding work_mem
* hash_mem_multiplier in size. We maintain a dlist of keys for this cache
and when we're adding new tuples and realize we've exceeded the memory
budget, we evict cache entries starting with the least recently used ones
until we have enough memory to add the new tuples to the cache.
For parameterized nested loop joins, we now consider using one of these
result cache nodes in between the nested loop node and its inner node. We
determine when this might be useful based on cost, which is primarily
driven off of what the expected cache hit ratio will be. Estimating the
cache hit ratio relies on having good distinct estimates on the nested
loop's parameters.
For now, the planner will only consider using a result cache for
parameterized nested loop joins. This works for both normal joins and
also for LATERAL type joins to subqueries. It is possible to use this new
node for other uses in the future. For example, to cache results from
correlated subqueries. However, that's not done here due to some
difficulties obtaining a distinct estimation on the outer plan to
calculate the estimated cache hit ratio. Currently we plan the inner plan
before planning the outer plan so there is no good way to know if a result
cache would be useful or not since we can't estimate the number of times
the subplan will be called until the outer plan is generated.
The functionality being added here is newly introducing a dependency on
the return value of estimate_num_groups() during the join search.
Previously, during the join search, we only ever needed to perform
selectivity estimations. With this commit, we need to use
estimate_num_groups() in order to estimate what the hit ratio on the
result cache will be. In simple terms, if we expect 10 distinct values
and we expect 1000 outer rows, then we'll estimate the hit ratio to be
99%. Since cache hits are very cheap compared to scanning the underlying
nodes on the inner side of the nested loop join, then this will
significantly reduce the planner's cost for the join. However, it's
fairly easy to see here that things will go bad when estimate_num_groups()
incorrectly returns a value that's significantly lower than the actual
number of distinct values. If this happens then that may cause us to make
use of a nested loop join with a result cache instead of some other join
type, such as a merge or hash join. Our distinct estimations have been
known to be a source of trouble in the past, so the extra reliance on them
here could cause the planner to choose slower plans than it did previous
to having this feature. Distinct estimations are also fairly hard to
estimate accurately when several tables have been joined already or when a
WHERE clause filters out a set of values that are correlated to the
expressions we're estimating the number of distinct value for.
For now, the costing we perform during query planning for result caches
does put quite a bit of faith in the distinct estimations being accurate.
When these are accurate then we should generally see faster execution
times for plans containing a result cache. However, in the real world, we
may find that we need to either change the costings to put less trust in
the distinct estimations being accurate or perhaps even disable this
feature by default. There's always an element of risk when we teach the
query planner to do new tricks that it decides to use that new trick at
the wrong time and causes a regression. Users may opt to get the old
behavior by turning the feature off using the enable_resultcache GUC.
Currently, this is enabled by default. It remains to be seen if we'll
maintain that setting for the release.
Additionally, the name "Result Cache" is the best name I could think of
for this new node at the time I started writing the patch. Nobody seems
to strongly dislike the name. A few people did suggest other names but no
other name seemed to dominate in the brief discussion that there was about
names. Let's allow the beta period to see if the current name pleases
enough people. If there's some consensus on a better name, then we can
change it before the release. Please see the 2nd discussion link below
for the discussion on the "Result Cache" name.
Author: David Rowley
Reviewed-by: Andy Fan, Justin Pryzby, Zhihong Yu
Tested-By: Konstantin Knizhnik
Discussion: https://postgr.es/m/CAApHDvrPcQyQdWERGYWx8J%2B2DLUNgXu%2BfOSbQ1UscxrunyXyrQ%40mail.gmail.com
Discussion: https://postgr.es/m/CAApHDvq=yQXr5kqhRviT2RhNKwToaWr9JAN5t+5_PzhuRJ3wvg@mail.gmail.com
It's misplaced there -- it's not libpq's output stream to tweak in that
way. In particular, POSIX says that it has to be called before any
other operation on the file, so if a stream previously used by the
calling application, bad things may happen.
Put setvbuf() in libpq_pipeline for good measure.
Also, reduce fopen(..., "w+") to just fopen(..., "w") in
libpq_pipeline.c. It's not clear that this fixes anything, but we don't
use w+ anywhere.
Per complaints from Tom Lane.
Discussion: https://postgr.es/m/3337422.1617229905@sss.pgh.pa.us
Some buildfarm animals with force_parallel_mode=regress were failing
this test because the error is reported in a parallel worker quicker
than the rows that succeed.
Take the opportunity to move the SET of lc_messages out of the traced
section, because it's not very interesting.
Diagnosed-by: Tom Lane <tgl@sss.pgh.pa.us>
Discussion: https://postgr.es/m/3304521.1617221724@sss.pgh.pa.us
Some compilers seem to be concerned about the possibility that
recv_step is not any of the defined enum values. Silence
warnings about uninitialized cmdtag in a different way than
I did in 9fb9691a8.
Test pipeline_abort was not checking that it got the rows it expected in
one mode; make it do so. This doesn't fix the actual problem (no idea
what that is, yet) but at least it should make it more obvious rather
than being visible only as a difference in the trace output.
While at it, fix other infelicities in the test:
* I reversed the order of result vs. expected in like().
* The output traces from -t are being put in the log dir, which means
the buildfarm script uselessly captures them. Put them in a separate
dir tmp_check/traces instead, to avoid cluttering the buildfarm results.
* Test pipelined_insert was using too large a row count. Reduce that a
tad and add a filler column to make each insert a little bulkier, while
still keeping enough that a buffer is filled and we have to switch mode.
According to the comments, when an invalid or dropped column oid is passed
to has_column_privilege(), the intention has always been to return NULL.
However, when the caller had table level privilege the invalid/missing
column was never discovered, because table permissions were checked first.
Fix that by introducing extended versions of pg_attribute_acl(check|mask)
and pg_class_acl(check|mask) which take a new argument, is_missing. When
is_missing is NULL, the old behavior is preserved. But when is_missing is
passed by the caller, no ERROR is thrown for dropped or missing
columns/relations, and is_missing is flipped to true. This in turn allows
has_column_privilege to check for column privileges first, providing the
desired semantics.
Not backpatched since it is a user visible behavioral change with no previous
complaints, and the fix is a bit on the invasive side.
Author: Joe Conway
Reviewed-By: Tom Lane
Reported by: Ian Barwick
Discussion: https://postgr.es/m/flat/9b5f4311-157b-4164-7fe7-077b4fe8ed84%40joeconway.com
This patch makes two closely related sets of changes:
1. For UPDATE, the subplan of the ModifyTable node now only delivers
the new values of the changed columns (i.e., the expressions computed
in the query's SET clause) plus row identity information such as CTID.
ModifyTable must re-fetch the original tuple to merge in the old
values of any unchanged columns. The core advantage of this is that
the changed columns are uniform across all tables of an inherited or
partitioned target relation, whereas the other columns might not be.
A secondary advantage, when the UPDATE involves joins, is that less
data needs to pass through the plan tree. The disadvantage of course
is an extra fetch of each tuple to be updated. However, that seems to
be very nearly free in context; even worst-case tests don't show it to
add more than a couple percent to the total query cost. At some point
it might be interesting to combine the re-fetch with the tuple access
that ModifyTable must do anyway to mark the old tuple dead; but that
would require a good deal of refactoring and it seems it wouldn't buy
all that much, so this patch doesn't attempt it.
2. For inherited UPDATE/DELETE, instead of generating a separate
subplan for each target relation, we now generate a single subplan
that is just exactly like a SELECT's plan, then stick ModifyTable
on top of that. To let ModifyTable know which target relation a
given incoming row refers to, a tableoid junk column is added to
the row identity information. This gets rid of the horrid hack
that was inheritance_planner(), eliminating O(N^2) planning cost
and memory consumption in cases where there were many unprunable
target relations.
Point 2 of course requires point 1, so that there is a uniform
definition of the non-junk columns to be returned by the subplan.
We can't insist on uniform definition of the row identity junk
columns however, if we want to keep the ability to have both
plain and foreign tables in a partitioning hierarchy. Since
it wouldn't scale very far to have every child table have its
own row identity column, this patch includes provisions to merge
similar row identity columns into one column of the subplan result.
In particular, we can merge the whole-row Vars typically used as
row identity by FDWs into one column by pretending they are type
RECORD. (It's still okay for the actual composite Datums to be
labeled with the table's rowtype OID, though.)
There is more that can be done to file down residual inefficiencies
in this patch, but it seems to be committable now.
FDW authors should note several API changes:
* The argument list for AddForeignUpdateTargets() has changed, and so
has the method it must use for adding junk columns to the query. Call
add_row_identity_var() instead of manipulating the parse tree directly.
You might want to reconsider exactly what you're adding, too.
* PlanDirectModify() must now work a little harder to find the
ForeignScan plan node; if the foreign table is part of a partitioning
hierarchy then the ForeignScan might not be the direct child of
ModifyTable. See postgres_fdw for sample code.
* To check whether a relation is a target relation, it's no
longer sufficient to compare its relid to root->parse->resultRelation.
Instead, check it against all_result_relids or leaf_result_relids,
as appropriate.
Amit Langote and Tom Lane
Discussion: https://postgr.es/m/CA+HiwqHpHdqdDn48yCEhynnniahH78rwcrv1rEX65-fsZGBOLQ@mail.gmail.com
This allows something like
SELECT ... FROM t1 JOIN t2 USING (a, b, c) AS x
where x has the columns a, b, c and unlike a regular alias it does not
hide the range variables of the tables being joined t1 and t2.
Per SQL:2016 feature F404 "Range variable for common column names".
Reviewed-by: Vik Fearing <vik.fearing@2ndquadrant.com>
Reviewed-by: Tom Lane <tgl@sss.pgh.pa.us>
Discussion: https://www.postgresql.org/message-id/flat/454638cf-d563-ab76-a585-2564428062af@2ndquadrant.com
This implements asynchronous execution, which runs multiple parts of a
non-parallel-aware Append concurrently rather than serially to improve
performance when possible. Currently, the only node type that can be
run concurrently is a ForeignScan that is an immediate child of such an
Append. In the case where such ForeignScans access data on different
remote servers, this would run those ForeignScans concurrently, and
overlap the remote operations to be performed simultaneously, so it'll
improve the performance especially when the operations involve
time-consuming ones such as remote join and remote aggregation.
We may extend this to other node types such as joins or aggregates over
ForeignScans in the future.
This also adds the support for postgres_fdw, which is enabled by the
table-level/server-level option "async_capable". The default is false.
Robert Haas, Kyotaro Horiguchi, Thomas Munro, and myself. This commit
is mostly based on the patch proposed by Robert Haas, but also uses
stuff from the patch proposed by Kyotaro Horiguchi and from the patch
proposed by Thomas Munro. Reviewed by Kyotaro Horiguchi, Konstantin
Knizhnik, Andrey Lepikhov, Movead Li, Thomas Munro, Justin Pryzby, and
others.
Discussion: https://postgr.es/m/CA%2BTgmoaXQEt4tZ03FtQhnzeDEMzBck%2BLrni0UWHVVgOTnA6C1w%40mail.gmail.com
Discussion: https://postgr.es/m/CA%2BhUKGLBRyu0rHrDCMC4%3DRn3252gogyp1SjOgG8SEKKZv%3DFwfQ%40mail.gmail.com
Discussion: https://postgr.es/m/20200228.170650.667613673625155850.horikyota.ntt%40gmail.com
We always inserted a larger-than-fillfactor tuple into a newly-extended
page, even when existing pages were empty or contained nothing but an
unused line pointer. This was unnecessary relation extension. Start
tolerating page usage up to 1/8 the maximum space that could be taken up
by line pointers. This is somewhat arbitrary, but it should allow more
cases to reuse pages. This has no effect on tables with fillfactor=100
(the default).
John Naylor and Floris van Nee. Reviewed by Matthias van de Meent.
Reported by Floris van Nee.
Discussion: https://postgr.es/m/6e263217180649339720afe2176c50aa@opammb0562.comp.optiver.com
When specified, only extensions matching the given pattern are included
in dumps. Similarly to --table and --schema, when --strict-names is
used, a perfect match is required. Also, like the two other options,
this new option offers no guarantee that dependent objects have been
dumped, so a restore may fail on a clean database.
Tests are added in test_pg_dump/, checking after a set of positive and
negative cases, with or without an extension's contents added to the
dump generated.
Author: Guillaume Lelarge
Reviewed-by: David Fetter, Tom Lane, Michael Paquier, Asif Rehman,
Julien Rouhaud
Discussion: https://postgr.es/m/CAECtzeXOt4cnMU5+XMZzxBPJ_wu76pNy6HZKPRBL-j7yj1E4+g@mail.gmail.com
The existing regression tests only tested the lower boundary of the
range supported by the timestamp and timestamptz types because "The
upper boundary differs between integer and float timestamps, so no
check". Since this is obsolete, add similar tests for the upper
boundary.
Currently we only recognize the Common Name (CN) of a certificate's
subject to be matched against the user name. Thus certificates with
subjects '/OU=eng/CN=fred' and '/OU=sales/CN=fred' will have the same
connection rights. This patch provides an option to match the whole
Distinguished Name (DN) instead of just the CN. On any hba line using
client certificate identity, there is an option 'clientname' which can
have values of 'DN' or 'CN'. The default is 'CN', the current procedure.
The DN is matched against the RFC2253 formatted DN, which looks like
'CN=fred,OU=eng'.
This facility of probably best used in conjunction with an ident map.
Discussion: https://postgr.es/m/92e70110-9273-d93c-5913-0bccb6562740@dunslane.net
Reviewed-By: Michael Paquier, Daniel Gustafsson, Jacob Champion
Some tests for timestamp and timestamptz were in the date.sql test
file. Move them to their appropriate files, or drop tests cases that
were already present there.
After some tests relating to standard_conforming_strings behavior, the
value was not reset to the default value. Therefore, the rest of the
tests in that file ran with the nondefault setting, which affected the
results of some tests. For clarity, reset the value and run the rest
of the tests with the default setting again.
The tests used string concatenation to test statistics on expressions,
but that made the tests locale-dependent, e.g. because the ordering of
'11' and '1X' depends on the collation. This affected both the estimated
and actual row couts, breaking some of the tests.
Fixed by replacing the string concatenation with upper() function call,
so that the text values contain only digits.
Discussion: https://postgr.es/m/b650920b-2767-fbc3-c87a-cb8b5d693cbf%40enterprisedb.com
Allow defining extended statistics on expressions, not just just on
simple column references. With this commit, expressions are supported
by all existing extended statistics kinds, improving the same types of
estimates. A simple example may look like this:
CREATE TABLE t (a int);
CREATE STATISTICS s ON mod(a,10), mod(a,20) FROM t;
ANALYZE t;
The collected statistics are useful e.g. to estimate queries with those
expressions in WHERE or GROUP BY clauses:
SELECT * FROM t WHERE mod(a,10) = 0 AND mod(a,20) = 0;
SELECT 1 FROM t GROUP BY mod(a,10), mod(a,20);
This introduces new internal statistics kind 'e' (expressions) which is
built automatically when the statistics object definition includes any
expressions. This represents single-expression statistics, as if there
was an expression index (but without the index maintenance overhead).
The statistics is stored in pg_statistics_ext_data as an array of
composite types, which is possible thanks to 79f6a942bd.
CREATE STATISTICS allows building statistics on a single expression, in
which case in which case it's not possible to specify statistics kinds.
A new system view pg_stats_ext_exprs can be used to display expression
statistics, similarly to pg_stats and pg_stats_ext views.
ALTER TABLE ... ALTER COLUMN ... TYPE now treats indexes the same way it
treats indexes, i.e. it drops and recreates the statistics. This means
all statistics are reset, and we no longer try to preserve at least the
functional dependencies. This should not be a major issue in practice,
as the functional dependencies actually rely on per-column statistics,
which were always reset anyway.
Author: Tomas Vondra
Reviewed-by: Justin Pryzby, Dean Rasheed, Zhihong Yu
Discussion: https://postgr.es/m/ad7891d2-e90c-b446-9fe2-7419143847d7%40enterprisedb.com
The regression tests of extended statistics were taking a fair amount of
time, due to using fairly large data sets with a couple thousand rows.
So far this was fine, but with tests for statistics on expressions the
duration would get a bit excessive. So reduce the size of some of the
tests that will be used to test expressions, to keep the duration under
control. Done in a separate commit before adding the statistics on
expressions, to make it clear which estimates are expected to change.
Author: Tomas Vondra
Discussion: https://postgr.es/m/ad7891d2-e90c-b446-9fe2-7419143847d7%40enterprisedb.com
When estimating the number of groups using extended statistics, the code
was discarding information about system attributes. This led to strange
situation that
SELECT 1 FROM t GROUP BY ctid;
could have produced higher estimate (equal to pg_class.reltuples) than
SELECT 1 FROM t GROUP BY a, b, ctid;
with extended statistics on (a,b). Fixed by retaining information about
the system attribute.
Backpatch all the way to 10, where extended statistics were introduced.
Author: Tomas Vondra
Backpatch-through: 10
Membership consists, implicitly, of the current database owner. Expect
use in template databases. Once pg_database_owner has rights within a
template, each owner of a database instantiated from that template will
exercise those rights.
Reviewed by John Naylor.
Discussion: https://postgr.es/m/20201228043148.GA1053024@rfd.leadboat.com
Adds BRIN opclasses similar to the existing minmax, except that instead
of summarizing the page range into a single [min,max] range, the summary
consists of multiple ranges and/or points, allowing gaps. This allows
more efficient handling of data with poor correlation to physical
location within the table and/or outlier values, for which the regular
minmax opclassed tend to work poorly.
It's possible to specify the number of values kept for each page range,
either as a single point or an interval boundary.
CREATE TABLE t (a int);
CREATE INDEX ON t
USING brin (a int4_minmax_multi_ops(values_per_range=16));
When building the summary, the values are combined into intervals with
the goal to minimize the "covering" (sum of interval lengths), using a
support procedure computing distance between two values.
Bump catversion, due to various catalog changes.
Author: Tomas Vondra <tomas.vondra@postgresql.org>
Reviewed-by: Alvaro Herrera <alvherre@alvh.no-ip.org>
Reviewed-by: Alexander Korotkov <aekorotkov@gmail.com>
Reviewed-by: Sokolov Yura <y.sokolov@postgrespro.ru>
Reviewed-by: John Naylor <john.naylor@enterprisedb.com>
Discussion: https://postgr.es/m/c1138ead-7668-f0e1-0638-c3be3237e812@2ndquadrant.com
Discussion: https://postgr.es/m/5d78b774-7e9c-c94e-12cf-fef51cc89b1a%402ndquadrant.com
Adds a BRIN opclass using a Bloom filter to summarize the range. Indexes
using the new opclasses allow only equality queries (similar to hash
indexes), but that works fine for data like UUID, MAC addresses etc. for
which range queries are not very common. This also means the indexes
work for data that is not well correlated to physical location within
the table, or perhaps even entirely random (which is a common issue with
existing BRIN minmax opclasses).
It's possible to specify opclass parameters with the usual Bloom filter
parameters, i.e. the desired false-positive rate and the expected number
of distinct values per page range.
CREATE TABLE t (a int);
CREATE INDEX ON t
USING brin (a int4_bloom_ops(false_positive_rate = 0.05,
n_distinct_per_range = 100));
The opclasses do not operate on the indexed values directly, but compute
a 32-bit hash first, and the Bloom filter is built on the hash value.
Collisions should not be a huge issue though, as the number of distinct
values in a page ranges is usually fairly small.
Bump catversion, due to various catalog changes.
Author: Tomas Vondra <tomas.vondra@postgresql.org>
Reviewed-by: Alvaro Herrera <alvherre@alvh.no-ip.org>
Reviewed-by: Alexander Korotkov <aekorotkov@gmail.com>
Reviewed-by: Sokolov Yura <y.sokolov@postgrespro.ru>
Reviewed-by: Nico Williams <nico@cryptonector.com>
Reviewed-by: John Naylor <john.naylor@enterprisedb.com>
Discussion: https://postgr.es/m/c1138ead-7668-f0e1-0638-c3be3237e812@2ndquadrant.com
Discussion: https://postgr.es/m/5d78b774-7e9c-c94e-12cf-fef51cc89b1a%402ndquadrant.com
Allow a partition be detached from its partitioned table without
blocking concurrent queries, by running in two transactions and only
requiring ShareUpdateExclusive in the partitioned table.
Because it runs in two transactions, it cannot be used in a transaction
block. This is the main reason to use dedicated syntax: so that users
can choose to use the original mode if they need it. But also, it
doesn't work when a default partition exists (because an exclusive lock
would still need to be obtained on it, in order to change its partition
constraint.)
In case the second transaction is cancelled or a crash occurs, there's
ALTER TABLE .. DETACH PARTITION .. FINALIZE, which executes the final
steps.
The main trick to make this work is the addition of column
pg_inherits.inhdetachpending, initially false; can only be set true in
the first part of this command. Once that is committed, concurrent
transactions that use a PartitionDirectory will include or ignore
partitions so marked: in optimizer they are ignored if the row is marked
committed for the snapshot; in executor they are always included. As a
result, and because of the way PartitionDirectory caches partition
descriptors, queries that were planned before the detach will see the
rows in the detached partition and queries that are planned after the
detach, won't.
A CHECK constraint is created that duplicates the partition constraint.
This is probably not strictly necessary, and some users will prefer to
remove it afterwards, but if the partition is re-attached to a
partitioned table, the constraint needn't be rechecked.
Author: Álvaro Herrera <alvherre@alvh.no-ip.org>
Reviewed-by: Amit Langote <amitlangote09@gmail.com>
Reviewed-by: Justin Pryzby <pryzby@telsasoft.com>
Discussion: https://postgr.es/m/20200803234854.GA24158@alvherre.pgsql
Currently instances of PostgresNode find their Postgres executables in
the PATH of the caller. This modification allows for instances that know
the installation path they are supposed to use, and the module adjusts
the environment of methods that call Postgres executables appropriately.
This facility is activated by passing the installation path to the
constructor:
my $node = PostgresNode->get_new_node('mynode',
installation_path => '/path/to/installation');
This makes a number of things substantially easier, including
. testing third party modules
. testing different versions of postgres together
. testing different builds of postgres together
Discussion: https://postgr.es/m/a94c74f9-6b71-1957-7973-a734ea3cbef1@dunslane.net
Reviewed-By: Alvaro Herrera, Michael Paquier, Dagfinn Ilmari Mannsåker
Common recommendations are that the checkpoint should be spread out as
much as possible, provided we avoid having it take too long. This
change updates the default to 0.9 (from 0.5) to match that
recommendation.
There was some debate about possibly removing the option entirely but it
seems there may be some corner-cases where having it set much lower to
try to force the checkpoint to be as fast as possible could result in
fewer periods of time of reduced performance due to kernel flushing.
General agreement is that the "spread more" is the preferred approach
though and those who need to tune away from that value are much less
common.
Reviewed-By: Michael Paquier, Peter Eisentraut, Tom Lane, David Steele,
Nathan Bossart
Discussion: https://postgr.es/m/20201207175329.GM16415%40tamriel.snowman.net
Change the default_toast_compression GUC to be an enum rather than
a string. Earlier, uncommitted versions of the patch supported using
CREATE ACCESS METHOD to add new compression methods to a running
system, but that idea was dropped before commit. So, we can simplify
the GUC handling as well, which has the nice side effect of improving
the error messages.
While updating the documentation to reflect the new GUC type, also
move it back to the right place in the list. I moved this while
revising what became commit 24f0e395ac,
but apparently the intended ordering is "alphabetical" rather than
"whatever Robert thinks looks nice."
Rejigger things to avoid having access/toast_compression.h depend on
utils/guc.h, so that we don't end up with every file that includes
it also depending on something largely unrelated. Move a few
inline functions back into the C source file partly to help reduce
dependencies and partly just to avoid clutter. A few very minor
cosmetic fixes.
Original patch by Justin Pryzby, but very heavily edited by me,
and reverse reviewed by him and also reviewed by by Tom Lane.
Discussion: http://postgr.es/m/CA+TgmoYp=GT_ztUCeZg2i4hkHAQv8o=-nVJ1-TKWTG1zQOmOpg@mail.gmail.com
Similar to date_trunc, but allows binning by an arbitrary interval
rather than just full units.
Author: John Naylor <john.naylor@enterprisedb.com>
Reviewed-by: David Fetter <david@fetter.org>
Reviewed-by: Isaac Morland <isaac.morland@gmail.com>
Reviewed-by: Tom Lane <tgl@sss.pgh.pa.us>
Reviewed-by: Artur Zakirov <zaartur@gmail.com>
Discussion: https://www.postgresql.org/message-id/flat/CACPNZCt4buQFRgy6DyjuZS-2aPDpccRkrJBmgUfwYc1KiaXYxg@mail.gmail.com
To allow inserts in parallel-mode this feature has to ensure that all the
constraints, triggers, etc. are parallel-safe for the partition hierarchy
which is costly and we need to find a better way to do that. Additionally,
we could have used existing cached information in some cases like indexes,
domains, etc. to determine the parallel-safety.
List of commits reverted, in reverse chronological order:
ed62d3737c Doc: Update description for parallel insert reloption.
c8f78b6161 Add a new GUC and a reloption to enable inserts in parallel-mode.
c5be48f092 Improve FK trigger parallel-safety check added by 05c8482f7f.
e2cda3c20a Fix use of relcache TriggerDesc field introduced by commit 05c8482f7f.
e4e87a32cc Fix valgrind issue in commit 05c8482f7f.
05c8482f7f Enable parallel SELECT for "INSERT INTO ... SELECT ...".
Discussion: https://postgr.es/m/E1lMiB9-0001c3-SY@gemulon.postgresql.org
end_heap_rewrite was not careful to ensure that the target relation
is open at the smgr level before performing its final smgrimmedsync.
In ordinary cases this is no problem, because it would have been
opened earlier during the rewrite. However a crash can be reproduced
by re-clustering an empty table with CLOBBER_CACHE_ALWAYS enabled.
Although that exact scenario does not crash in v13, I think that's
a chance result of unrelated planner changes, and the problem is
likely still reachable with other test cases. The true proximate
cause of this failure is commit c6b92041d, which replaced a call to
heap_sync (which was careful about opening smgr) with a direct call
to smgrimmedsync. Hence, back-patch to v13.
Amul Sul, per report from Neha Sharma; cosmetic changes
and test case by me.
Discussion: https://postgr.es/m/CANiYTQsU7yMFpQYnv=BrcRVqK_3U3mtAzAsJCaqtzsDHfsUbdQ@mail.gmail.com
This function for bit and bytea counts the set bits in the bit or byte
string. Internally, we use the existing popcount functionality.
For the name, after some discussion, we settled on bit_count, which
also exists with this meaning in MySQL, Java, and Python.
Author: David Fetter <david@fetter.org>
Discussion: https://www.postgresql.org/message-id/flat/20201230105535.GJ13234@fetter.org
The test added by 595b9cb forgot that on Windows it is necessary to set
up pg_hba.conf (see PostgresNode::set_replication_conf) with a specific
entry or base backups fail. Any node that requires to support
replication just needs to pass down allows_streaming at initialization.
This updates the test to do so. Simplify things a bit while on it.
Per buildfarm member fairywren. Any Windows hosts running this test
would have failed, and I have reproduced the problem as well.
Backpatch-through: 10
The TAP tests of kerberos rely on the logs generated by the backend to
check various connection scenarios. In order to make sure that a given
test does not overlap with the log contents generated by a previous
test, the test suite relied on a logic with the logging collector and a
rotation of the log files to ensure the uniqueness of the log generated
with a wait phase.
Parsing the log contents for expected patterns is a problem that has
been solved in a simpler way by PostgresNode::issues_sql_like() where
the log file is truncated before checking for the contents generated,
with the backend sending its output to a log file given by pg_ctl
instead. This commit switches the kerberos test suite to use such a
method, removing any wait phase and simplifying the whole logic,
resulting in less code. If a failure happens in the tests, the contents
of the logs are still showed to the user at the moment of the failure
thanks to like(), so this has no impact on debugging capabilities.
I have bumped into this issue while reviewing a different patch set
aiming at extending the kerberos test suite to check for multiple
log patterns instead of one now.
Author: Michael Paquier
Reviewed-by: Stephen Frost, Bharath Rupireddy
Discussion: https://postgr.es/m/YFXcq2vBTDGQVBNC@paquier.xyz
Any transactions found as still prepared by a checkpoint have their
state data read from the WAL records generated by PREPARE TRANSACTION
before being moved into their new location within pg_twophase/. While
reading such records, the WAL reader uses the callback
read_local_xlog_page() to read a page, that is shared across various
parts of the system. This callback, since 1148e22a, has introduced an
update of ThisTimeLineID when reading a record while in recovery, which
is potentially helpful in the context of cascading WAL senders.
This update of ThisTimeLineID interacts badly with the checkpointer if a
promotion happens while some 2PC data is read from its record, as, by
changing ThisTimeLineID, any follow-up WAL records would be written to
an timeline older than the promoted one. This results in consistency
issues. For instance, a subsequent server restart would cause a failure
in finding a valid checkpoint record, resulting in a PANIC, for
instance.
This commit changes the code reading the 2PC data to reset the timeline
once the 2PC record has been read, to prevent messing up with the static
state of the checkpointer. It would be tempting to do the same thing
directly in read_local_xlog_page(). However, based on the discussion
that has led to 1148e22a, users may rely on the updates of
ThisTimeLineID when a WAL record page is read in recovery, so changing
this callback could break some cases that are working currently.
A TAP test reproducing the issue is added, relying on a PITR to
precisely trigger a promotion with a prepared transaction still
tracked.
Per discussion with Heikki Linnakangas, Kyotaro Horiguchi, Fujii Masao
and myself.
Author: Soumyadeep Chakraborty, Jimmy Yih, Kevin Yeap
Discussion: https://postgr.es/m/CAE-ML+_EjH_fzfq1F3RJ1=XaaNG=-Jz-i3JqkNhXiLAsM3z-Ew@mail.gmail.com
Backpatch-through: 10
This reverts commit 677271a3a1.
"Unbreak recovery test on Windows"
The test hangs on Windows, and attempts to remedy the problem have
proved fragile at best. So we simply disable the test on Windows perl.
(Msys perl seems perfectly happy).
Discussion: https://postgr.es/m/5b748470-7335-5439-e876-6a88c951e1c5@dunslane.net
Compilers that don't understand that elog(ERROR) doesn't return
issued warnings here. In the cases in libpq_pipeline.c, we were
not exactly helping things by failing to mark pg_fatal() as noreturn.
Per buildfarm.
There is now a per-column COMPRESSION option which can be set to pglz
(the default, and the only option in up until now) or lz4. Or, if you
like, you can set the new default_toast_compression GUC to lz4, and
then that will be the default for new table columns for which no value
is specified. We don't have lz4 support in the PostgreSQL code, so
to use lz4 compression, PostgreSQL must be built --with-lz4.
In general, TOAST compression means compression of individual column
values, not the whole tuple, and those values can either be compressed
inline within the tuple or compressed and then stored externally in
the TOAST table, so those properties also apply to this feature.
Prior to this commit, a TOAST pointer has two unused bits as part of
the va_extsize field, and a compessed datum has two unused bits as
part of the va_rawsize field. These bits are unused because the length
of a varlena is limited to 1GB; we now use them to indicate the
compression type that was used. This means we only have bit space for
2 more built-in compresison types, but we could work around that
problem, if necessary, by introducing a new vartag_external value for
any further types we end up wanting to add. Hopefully, it won't be
too important to offer a wide selection of algorithms here, since
each one we add not only takes more coding but also adds a build
dependency for every packager. Nevertheless, it seems worth doing
at least this much, because LZ4 gets better compression than PGLZ
with less CPU usage.
It's possible for LZ4-compressed datums to leak into composite type
values stored on disk, just as it is for PGLZ. It's also possible for
LZ4-compressed attributes to be copied into a different table via SQL
commands such as CREATE TABLE AS or INSERT .. SELECT. It would be
expensive to force such values to be decompressed, so PostgreSQL has
never done so. For the same reasons, we also don't force recompression
of already-compressed values even if the target table prefers a
different compression method than was used for the source data. These
architectural decisions are perhaps arguable but revisiting them is
well beyond the scope of what seemed possible to do as part of this
project. However, it's relatively cheap to recompress as part of
VACUUM FULL or CLUSTER, so this commit adjusts those commands to do
so, if the configured compression method of the table happens not to
match what was used for some column value stored therein.
Dilip Kumar. The original patches on which this work was based were
written by Ildus Kurbangaliev, and those were patches were based on
even earlier work by Nikita Glukhov, but the design has since changed
very substantially, since allow a potentially large number of
compression methods that could be added and dropped on a running
system proved too problematic given some of the architectural issues
mentioned above; the choice of which specific compression method to
add first is now different; and a lot of the code has been heavily
refactored. More recently, Justin Przyby helped quite a bit with
testing and reviewing and this version also includes some code
contributions from him. Other design input and review from Tomas
Vondra, Álvaro Herrera, Andres Freund, Oleg Bartunov, Alexander
Korotkov, and me.
Discussion: http://postgr.es/m/20170907194236.4cefce96%40wp.localdomain
Discussion: http://postgr.es/m/CAFiTN-uUpX3ck%3DK0mLEk-G_kUQY%3DSNOTeqdaNRR9FMdQrHKebw%40mail.gmail.com
The TAP test was written so that it was not waiting for the correct SQL
command, but for output from the preceding one. This resulted in race
conditions, allowing the commands to run in a different order, not block
as expected and so on. This fixes it by inverting the order of commands
where possible, so that observing the output guarantees the data was
inserted properly, and waiting for a lock to appear in pg_locks.
Discussion: https://postgr.es/m/CAH503wDKdYzyq7U-QJqGn%3DGm6XmoK%2B6_6xTJ-Yn5WSvoHLY1Ww%40mail.gmail.com
The test included in cd91de0d17 had two simple flaws.
Firstly, the number of rows was low and on some platforms (e.g. 32-bit)
the sort did not require on-disk sort, so on those machines it was not
testing the automatic removal. The test was however failing, because
without any temporary files the base/pgsql_tmp directory was not even
created. Fixed by increasing the rowcount to 5000, which should be high
engough on any platform.
Secondly, the test used a simple sleep to wait for the temporary file to
be created. This is obviously problematic, because on slow machines (or
with valgrind, CLOBBER_CACHE_ALWAYS etc.) it may take a while to create
the temporary file. But we also want the tests run reasonably fast.
Fixed by instead relying on a UNIQUE constraint, blocking the query that
created the temporary file.
Author: Euler Taveira
Reviewed-by: Tomas Vondra
Discussion: https://postgr.es/m/CAH503wDKdYzyq7U-QJqGn%3DGm6XmoK%2B6_6xTJ-Yn5WSvoHLY1Ww%40mail.gmail.com
With grouping sets, it's possible that some of the grouping sets are
duplicate. This is especially common with CUBE and ROLLUP clauses. For
example GROUP BY CUBE (a,b), CUBE (b,c) is equivalent to
GROUP BY GROUPING SETS (
(a, b, c),
(a, b, c),
(a, b, c),
(a, b),
(a, b),
(a, b),
(a),
(a),
(a),
(c, a),
(c, a),
(c, a),
(c),
(b, c),
(b),
()
)
Some of the grouping sets are calculated multiple times, which is mostly
unnecessary. This commit implements a new GROUP BY DISTINCT feature, as
defined in the SQL standard, which eliminates the duplicate sets.
Author: Vik Fearing
Reviewed-by: Erik Rijkers, Georgios Kokolatos, Tomas Vondra
Discussion: https://postgr.es/m/bf3805a8-d7d1-ae61-fece-761b7ff41ecc@postgresfriends.org
After a crash of a backend using temporary files, the files used to be
left behind, on the basis that it might be useful for debugging. But we
don't have any reports of anyone actually doing that, and it means the
disk usage may grow over time due to repeated backend failures (possibly
even hitting ENOSPC). So this behavior is a bit unfortunate, and fixing
it required either manual cleanup (deleting files, which is error-prone)
or restart of the instance (i.e. service disruption).
This implements automatic cleanup of temporary files, controled by a new
GUC remove_temp_files_after_crash. By default the files are removed, but
it can be disabled to restore the old behavior if needed.
Author: Euler Taveira
Reviewed-by: Tomas Vondra, Michael Paquier, Anastasia Lubennikova, Thomas Munro
Discussion: https://postgr.es/m/CAH503wDKdYzyq7U-QJqGn%3DGm6XmoK%2B6_6xTJ-Yn5WSvoHLY1Ww%40mail.gmail.com
Commit 05c8482f7f added the implementation of parallel SELECT for
"INSERT INTO ... SELECT ..." which may incur non-negligible overhead in
the additional parallel-safety checks that it performs, even when, in the
end, those checks determine that parallelism can't be used. This is
normally only ever a problem in the case of when the target table has a
large number of partitions.
A new GUC option "enable_parallel_insert" is added, to allow insert in
parallel-mode. The default is on.
In addition to the GUC option, the user may want a mechanism to allow
inserts in parallel-mode with finer granularity at table level. The new
table option "parallel_insert_enabled" allows this. The default is true.
Author: "Hou, Zhijie"
Reviewed-by: Greg Nancarrow, Amit Langote, Takayuki Tsunakawa, Amit Kapila
Discussion: https://postgr.es/m/CAA4eK1K-cW7svLC2D7DHoGHxdAdg3P37BLgebqBOC2ZLc9a6QQ%40mail.gmail.com
Discussion: https://postgr.es/m/CAJcOf-cXnB5cnMKqWEp2E2z7Mvcd04iLVmV=qpFJrR3AcrTS3g@mail.gmail.com
The existing test script does run pg_basebackup with the -Ft option,
but it makes no real attempt to verify the sanity of the results.
We wouldn't know if the output is incompatible with standard "tar"
programs, nor if the server fails to start from the restored output.
Notably, this means that xlog.c's read_tablespace_map() is not being
meaningfully tested, since that code is used only in the tar-format
case. (We do have reasonable coverage of restoring from plain-format
output, though it's over in src/test/recovery not here.)
Hence, attempt to untar the output and start a server from it,
rather just hoping it's OK.
This test assumes that the local "tar" has the "-C directory"
switch. Although that's not promised by POSIX, my research
suggests that all non-extinct tar implementations have it.
Should the buildfarm's opinion differ, we can complicate the
test a bit to avoid requiring that.
Possibly this should be back-patched, but I'm unsure about
whether it could work on Windows before d66b23b03.
It seems like a useful sanity check to be able to run "installcheck"
against a cluster running with default_transaction_level set to
serializable or repeatable read. Only one thing currently fails in
those configurations, so let's fix that.
No back-patch for now, because it fails in many other places in some of
the stable branches. We'd have to go back and fix those too if we
included this configuration in automated testing.
Reviewed-by: Tom Lane <tgl@sss.pgh.pa.us>
Discussion: https://postgr.es/m/CA%2BhUKGJUaHeK%3DHLATxF1JOKDjKJVrBKA-zmbPAebOM0Se2FQRg%40mail.gmail.com
Pass CURSOR_OPT_PARALLEL_OK to pg_plan_query() so that parallel plans
are considered when running the underlying SELECT query. This wasn't
done in commit e9baa5e9, which did this for CREATE MATERIALIZED VIEW,
because it wasn't yet known to be safe.
Since REFRESH always inserts into a freshly created table before later
merging or swapping the data into place with separate operations, we can
enable such plans here too.
Author: Bharath Rupireddy <bharath.rupireddyforpostgres@gmail.com>
Reviewed-by: Hou, Zhijie <houzj.fnst@cn.fujitsu.com>
Reviewed-by: Luc Vlaming <luc@swarm64.com>
Reviewed-by: Thomas Munro <thomas.munro@gmail.com>
Discussion: https://postgr.es/m/CALj2ACXg-4hNKJC6nFnepRHYT4t5jJVstYvri%2BtKQHy7ydcr8A%40mail.gmail.com
I forgot that Windows represents newlines as \r\n, so splitting a string
at /\s/ creates additional empty strings. Let's rewrite that as /\s+/
to see if that avoids those. (There's precedent for using that pattern
on Windows in other scripts.)
Previously: 91bdf499b3, 8ed428dc97, 650b967076.
Per buildfarm, via Tom Lane.
Discussion: https://postgr.es/m/3144460.1615860259@sss.pgh.pa.us
This tests some basic features for progress reporting of COPY, relying
on an INSERT trigger that gets fired when doing COPY FROM with a file or
stdin, checking for sizes, number of tuples processed, and number of
tuples excluded by a WHERE clause.
Author: Josef Šimánek, Matthias van de Meent
Reviewed-by: Michael Paquier, Justin Pryzby, Bharath Rupireddy, Tomas
Vondra
Discussion: https://postgr.es/m/CAEze2WiOcgdH4aQA8NtZq-4dgvnJzp8PohdeKchPkhMY-jWZXA@mail.gmail.com
Pipeline mode in libpq lets an application avoid the Sync messages in
the FE/BE protocol that are implicit in the old libpq API after each
query. The application can then insert Sync at its leisure with a new
libpq function PQpipelineSync. This can lead to substantial reductions
in query latency.
Co-authored-by: Craig Ringer <craig.ringer@enterprisedb.com>
Co-authored-by: Matthieu Garrigues <matthieu.garrigues@gmail.com>
Co-authored-by: Álvaro Herrera <alvherre@alvh.no-ip.org>
Reviewed-by: Andres Freund <andres@anarazel.de>
Reviewed-by: Aya Iwata <iwata.aya@jp.fujitsu.com>
Reviewed-by: Daniel Vérité <daniel@manitou-mail.org>
Reviewed-by: David G. Johnston <david.g.johnston@gmail.com>
Reviewed-by: Justin Pryzby <pryzby@telsasoft.com>
Reviewed-by: Kirk Jamison <k.jamison@fujitsu.com>
Reviewed-by: Michael Paquier <michael.paquier@gmail.com>
Reviewed-by: Nikhil Sontakke <nikhils@2ndquadrant.com>
Reviewed-by: Vaishnavi Prabakaran <VaishnaviP@fast.au.fujitsu.com>
Reviewed-by: Zhihong Yu <zyu@yugabyte.com>
Discussion: https://postgr.es/m/CAMsr+YFUjJytRyV4J-16bEoiZyH=4nj+sQ7JP9ajwz=B4dMMZw@mail.gmail.com
Discussion: https://postgr.es/m/CAJkzx4T5E-2cQe3dtv2R78dYFvz+in8PY7A8MArvLhs_pg75gg@mail.gmail.com
SERIALIZABLE no longer inhibits parallelism, so we can drop some
outdated workarounds and comments from regression tests. The change
came in release 12, commit bb16aba5, but it's not really worth
back-patching.
Also fix a typo.
Reviewed-by: Bharath Rupireddy <bharath.rupireddyforpostgres@gmail.com>
Discussion: https://postgr.es/m/CA%2BhUKGJUaHeK%3DHLATxF1JOKDjKJVrBKA-zmbPAebOM0Se2FQRg%40mail.gmail.com
GENERATED ALWAYS AS IDENTITY implies NOT NULL, but the code failed
to complain if you overrode that with "GENERATED ALWAYS AS IDENTITY
NULL". One might think the old behavior was a feature, but it was
inconsistent because the outcome varied depending on the order of
the clauses, so it seems to have been just an oversight.
Per bug #16913 from Pavel Boev. Back-patch to v10 where identity
columns were introduced.
Vik Fearing (minor tweaks by me)
Discussion: https://postgr.es/m/16913-3b5198410f67d8c6@postgresql.org
Remove the entire idea of "stale stats" within nbtree VACUUM (stop
caring about stats involving the number of inserted tuples). Also
remove the vacuum_cleanup_index_scale_factor GUC/param on the master
branch (though just disable them on postgres 13).
The vacuum_cleanup_index_scale_factor/stats interface made the nbtree AM
partially responsible for deciding when pg_class.reltuples stats needed
to be updated. This seems contrary to the spirit of the index AM API,
though -- it is not actually necessary for an index AM's bulk delete and
cleanup callbacks to provide accurate stats when it happens to be
inconvenient. The core code owns that. (Index AMs have the authority
to perform or not perform certain kinds of deferred cleanup based on
their own considerations, such as page deletion and recycling, but that
has little to do with pg_class.reltuples/num_index_tuples.)
This issue was fairly harmless until the introduction of the
autovacuum_vacuum_insert_threshold feature by commit b07642db, which had
an undesirable interaction with the vacuum_cleanup_index_scale_factor
mechanism: it made insert-driven autovacuums perform full index scans,
even though there is no real benefit to doing so. This has been tied to
a regression with an append-only insert benchmark [1].
Also have remaining cases that perform a full scan of an index during a
cleanup-only nbtree VACUUM indicate that the final tuple count is only
an estimate. This prevents vacuumlazy.c from setting the index's
pg_class.reltuples in those cases (it will now only update pg_class when
vacuumlazy.c had TIDs for nbtree to bulk delete). This arguably fixes
an oversight in deduplication-related bugfix commit 48e12913.
[1] https://smalldatum.blogspot.com/2021/01/insert-benchmark-postgres-is-still.html
Author: Peter Geoghegan <pg@bowt.ie>
Reviewed-By: Masahiko Sawada <sawada.mshk@gmail.com>
Discussion: https://postgr.es/m/CAD21AoA4WHthN5uU6+WScZ7+J_RcEjmcuH94qcoUPuB42ShXzg@mail.gmail.com
Backpatch: 13-, where autovacuum_vacuum_insert_threshold was added.
When a foreign key constraint is applied to a partitioned table, each
leaf partition inherits a similar FK constraint. We were processing all
of those constraints independently, meaning that in large partitioning
trees we'd build up large collections of cached FK-checking query plans.
However, in all cases but one, the generated queries are actually
identical for all members of the inheritance tree (because, in most
cases, the query only mentions the topmost table of the other side of
the FK relationship). So we can share a single cached plan among all
the partitions, saving memory, not to mention time to build and maintain
the cached plans.
Keisuke Kuroda and Amit Langote
Discussion: https://postgr.es/m/cab4b85d-9292-967d-adf2-be0d803c3e23@nttcom.co.jp_1
Moving this logic into pg_regress fixes a potential failure with
parallel tests when pg_upgrade and the main regression test suite both
trigger the makefile rule that cleaned up testtablespace/ under
src/test/regress. Even if pg_upgrade was triggering this rule, it has
no need to do so as it uses a different tablespace path. So if
pg_upgrade triggered the makefile rule for the tablespace setup while
the main regression test suite ran the tablespace cases, it would fail.
61be85a was a similar attempt at achieving that, but that broke cases
where the regression tests require to run under an Administrator
account, like with Appveyor.
Reported-by: Andres Freund, Kyotaro Horiguchi
Reviewed-by: Peter Eisentraut
Discussion: https://postgr.es/m/20201209012911.uk4d6nxcnkp7ehrx@alap3.anarazel.de
Parallel SELECT can't be utilized for INSERT in the following cases:
- INSERT statement uses the ON CONFLICT DO UPDATE clause
- Target table has a parallel-unsafe: trigger, index expression or
predicate, column default expression or check constraint
- Target table has a parallel-unsafe domain constraint on any column
- Target table is a partitioned table with a parallel-unsafe partition key
expression or support function
The planner is updated to perform additional parallel-safety checks for
the cases listed above, for determining whether it is safe to run INSERT
in parallel-mode with an underlying parallel SELECT. The planner will
consider using parallel SELECT for "INSERT INTO ... SELECT ...", provided
nothing unsafe is found from the additional parallel-safety checks, or
from the existing parallel-safety checks for SELECT.
While checking parallel-safety, we need to check it for all the partitions
on the table which can be costly especially when we decide not to use a
parallel plan. So, in a separate patch, we will introduce a GUC and or a
reloption to enable/disable parallelism for Insert statements.
Prior to entering parallel-mode for the execution of INSERT with parallel
SELECT, a TransactionId is acquired and assigned to the current
transaction state. This is necessary to prevent the INSERT from attempting
to assign the TransactionId whilst in parallel-mode, which is not allowed.
This approach has a disadvantage in that if the underlying SELECT does not
return any rows, then the TransactionId is not used, however that
shouldn't happen in practice in many cases.
Author: Greg Nancarrow, Amit Langote, Amit Kapila
Reviewed-by: Amit Langote, Hou Zhijie, Takayuki Tsunakawa, Antonin Houska, Bharath Rupireddy, Dilip Kumar, Vignesh C, Zhihong Yu, Amit Kapila
Tested-by: Tang, Haiying
Discussion: https://postgr.es/m/CAJcOf-cXnB5cnMKqWEp2E2z7Mvcd04iLVmV=qpFJrR3AcrTS3g@mail.gmail.com
Discussion: https://postgr.es/m/CAJcOf-fAdj=nDKMsRhQzndm-O13NY4dL6xGcEvdX5Xvbbi0V7g@mail.gmail.com
This partially reverts 096bbf7 and 9d2d457, undoing the libpq changes as
it could cause breakages in distributions that share one single libpq
version across multiple major versions of Postgres for extensions and
applications linking to that.
Note that the backend is unchanged here, and it still disables SSL
compression while simplifying the underlying catalogs that tracked if
compression was enabled or not for a SSL connection.
Per discussion with Tom Lane and Daniel Gustafsson.
Discussion: https://postgr.es/m/YEbq15JKJwIX+S6m@paquier.xyz
The authtype parameter was deprecated and made inactive in commit
d5bbe2aca5, but the environment variable was left defined and thus
tested with a getenv call even though the value is of no use. Also,
if it would exist it would be copied but never freed as the cleanup
code had been removed.
tty was deprecated in commit cb7fb3ca95 but most of the
infrastructure around it remained in place.
Author: Daniel Gustafsson <daniel@yesql.se>
Discussion: https://postgr.es/m/DDDF36F3-582A-4C02-8598-9B464CC42B34@yesql.se
This commit adds new GUC track_wal_io_timing. When this is enabled,
the total amounts of time XLogWrite writes and issue_xlog_fsync syncs
WAL data to disk are counted in pg_stat_wal. This information would be
useful to check how much WAL write and sync affect the performance.
Enabling track_wal_io_timing will make the server query the operating
system for the current time every time WAL is written or synced,
which may cause significant overhead on some platforms. To avoid such
additional overhead in the server with track_io_timing enabled,
this commit introduces track_wal_io_timing as a separate parameter from
track_io_timing.
Note that WAL write and sync activity by walreceiver has not been tracked yet.
This commit makes the server also track the numbers of times XLogWrite
writes and issue_xlog_fsync syncs WAL data to disk, in pg_stat_wal,
regardless of the setting of track_wal_io_timing. This counters can be
used to calculate the WAL write and sync time per request, for example.
Bump PGSTAT_FILE_FORMAT_ID.
Bump catalog version.
Author: Masahiro Ikeda
Reviewed-By: Japin Li, Hayato Kuroda, Masahiko Sawada, David Johnston, Fujii Masao
Discussion: https://postgr.es/m/0509ad67b585a5b86a83d445dfa75392@oss.nttdata.com
The command (TO or FROM), its type (file, pipe, program or callback),
and the number of tuples excluded by a WHERE clause in COPY FROM are
added to the progress reporting already available.
The column "lines_processed" is renamed to "tuples_processed" to
disambiguate the meaning of this column in the cases of CSV and BINARY
COPY and to be more consistent with the other catalog progress views.
Bump catalog version, again.
Author: Matthias van de Meent
Reviewed-by: Michael Paquier, Justin Pryzby, Bharath Rupireddy, Josef
Šimánek, Tomas Vondra
Discussion: https://postgr.es/m/CAEze2WiOcgdH4aQA8NtZq-4dgvnJzp8PohdeKchPkhMY-jWZXA@mail.gmail.com
PostgreSQL disabled compression as of e3bdb2d and the documentation
recommends against using it since. Additionally, SSL compression has
been disabled in OpenSSL since version 1.1.0, and was disabled in many
distributions long before that. The most recent TLS version, TLSv1.3,
disallows compression at the protocol level.
This commit removes the feature itself, removing support for the libpq
parameter sslcompression (parameter still listed for compatibility
reasons with existing connection strings, just ignored), and removes
the equivalent field in pg_stat_ssl and de facto PgBackendSSLStatus.
Note that, on top of removing the ability to activate compression by
configuration, compression is actively disabled in both frontend and
backend to avoid overrides from local configurations.
A TAP test is added for deprecated SSL parameters to check after
backwards compatibility.
Bump catalog version.
Author: Daniel Gustafsson
Reviewed-by: Peter Eisentraut, Magnus Hagander, Michael Paquier
Discussion: https://postgr.es/m/7E384D48-11C5-441B-9EC3-F7DB1F8518F6@yesql.se
Under windows, psql processes need to be ended explicitly, or the TAP
tests hang. However, the recovery tests were doing this via
IPC::Run::kill_kill(), which causes other major problems on Windows.
We solve this by instead sending '\q' to psql so it quits of its own
accord, and then simply waiting for it. This means we can now run almost
all the recovery tests on all Windows platforms.
Discussion: https://postgr.es/m/20210301200715.tdjpuesfzebpffgn@alap3.anarazel.de
Feed the desired command to psql via "-c" not stdin, else Perl
may complain that it can't push stdin to an already-failed psql
process, as seen in intermittent buildfarm failures.
Make some minor cosmetic improvements while at it.
Before commit ee28cacf6 we had no tests here that expected failure
to connect, so there seems no need for a back-patch.
Discussion: https://postgr.es/m/CALDaNm2mo8YED=M2ZJKGf1U3F3mw6SaQuLXWCK8rZP6sECYcrA@mail.gmail.com
Commit 0aa8a01d04 extends the output plugin API to allow decoding of
prepared xacts and allowed the user to enable/disable the two-phase option
via pg_logical_slot_get_changes(). This can lead to a problem such that
the first time when it gets changes via pg_logical_slot_get_changes()
without two_phase option enabled it will not get the prepared even though
prepare is after consistent snapshot. Now next time during getting changes,
if the two_phase option is enabled it can skip prepare because by that
time start decoding point has been moved. So the user will only get commit
prepared.
Allow to enable/disable this option at the create slot time and default
will be false. It will break the existing slots which is fine in a major
release.
Author: Ajin Cherian
Reviewed-by: Amit Kapila and Vignesh C
Discussion: https://postgr.es/m/d0f60d60-133d-bf8d-bd70-47784d8fabf3@enterprisedb.com
In addition to the existing options of "any" and "read-write", we
now support "read-only", "primary", "standby", and "prefer-standby".
"read-write" retains its previous meaning of "transactions are
read-write by default", and "read-only" inverts that. The other
three modes test specifically for hot-standby status, which is not
quite the same thing. (Setting default_transaction_read_only on
a primary server renders it read-only to this logic, but not a
standby.)
Furthermore, if talking to a v14 or later server, no extra network
round trip is needed to detect the session's status; the GUC_REPORT
variables delivered by the server are enough. When talking to an
older server, a SHOW or SELECT query is issued to detect session
read-only-ness or server hot-standby state, as needed.
Haribabu Kommi, Greg Nancarrow, Vignesh C, Tom Lane; reviewed at
various times by Laurenz Albe, Takayuki Tsunakawa, Peter Smith.
Discussion: https://postgr.es/m/CAF3+xM+8-ztOkaV9gHiJ3wfgENTq97QcjXQt+rbFQ6F7oNzt9A@mail.gmail.com
POSIX defines the behavior of back-references thus:
The back-reference expression '\n' shall match the same (possibly
empty) string of characters as was matched by a subexpression
enclosed between "\(" and "\)" preceding the '\n'.
As far as I can see, the back-reference is supposed to consider only
the data characters matched by the referenced subexpression. However,
because our engine copies the NFA constructed from the referenced
subexpression, it effectively enforces any constraints therein, too.
As an example, '(^.)\1' ought to match 'xx', or any other string
starting with two occurrences of the same character; but in our code
it does not, and indeed can't match anything, because the '^' anchor
constraint is included in the backref's copied NFA. If POSIX intended
that, you'd think they'd mention it. Perl for one doesn't act that
way, so it's hard to conclude that this isn't a bug.
Fix by modifying the backref's NFA immediately after it's copied from
the reference, replacing all constraint arcs by EMPTY arcs so that the
constraints are treated as automatically satisfied. This still allows
us to enforce matching rules that depend only on the data characters;
for example, in '(^\d+).*\1' the NFA matching step will still know
that the backref can only match strings of digits.
Perhaps surprisingly, this change does not affect the results of any
of a rather large corpus of real-world regexes. Nonetheless, I would
not consider back-patching it, since it's a clear compatibility break.
Patch by me, reviewed by Joel Jacobson
Discussion: https://postgr.es/m/661609.1614560029@sss.pgh.pa.us
Point to the specific line where the error was detected; the
previous code tended to include several preceding lines as well.
Avoid re-scanning the entire input to recompute which line that
was. Simplify the logic a bit. Add test cases.
Simon Riggs and Hamid Akhtar, reviewed by Daniel Gustafsson and myself
Discussion: https://postgr.es/m/CANbhV-EPBnXm3MF_TTWBwwqgn1a1Ghmep9VHfqmNBQ8BT0f+_g@mail.gmail.com
The psql processes were not explicitly killed (but would eventually
exit due postgres shutting down). For some reason windows perl doesn't
like that, resulting in errors like
Warning: unable to close filehandle GEN20 properly: Bad file descriptor during global destruction.
The test was introduced in d6734a897e3, so no backpatching necessary.
AfterTriggerSaveEvent() wrongly allocates the slot in execution-span
memory context, whereas the correct thing is to allocate it in
a transaction-span context, because that's where the enclosing
AfterTriggersTableData instance belongs into.
Backpatch to 12 (the test back to 11, where it works well with no code
changes, and it's good to have to confirm that the case was previously
well supported); this bug seems introduced by commit ff11e7f4b9.
Reported-by: Bertrand Drouvot <bdrouvot@amazon.com>
Author: Amit Langote <amitlangote09@gmail.com>
Discussion: https://postgr.es/m/39a71864-b120-5a5c-8cc5-c632b6f16761@amazon.com
This adds a new executor node named TID Range Scan. The query planner
will generate paths for TID Range scans when quals are discovered on base
relations which search for ranges on the table's ctid column. These
ranges may be open at either end. For example, WHERE ctid >= '(10,0)';
will return all tuples on page 10 and over.
To support this, two new optional callback functions have been added to
table AM. scan_set_tidrange is used to set the scan range to just the
given range of TIDs. scan_getnextslot_tidrange fetches the next tuple
in the given range.
For AMs were scanning ranges of TIDs would not make sense, these functions
can be set to NULL in the TableAmRoutine. The query planner won't
generate TID Range Scan Paths in that case.
Author: Edmund Horner, David Rowley
Reviewed-by: David Rowley, Tomas Vondra, Tom Lane, Andres Freund, Zhihong Yu
Discussion: https://postgr.es/m/CAMyN-kB-nFTkF=VA_JPwFNo08S0d-Yk0F741S2B7LDmYAi8eyA@mail.gmail.com
makeDependencyGraphWalker and checkWellFormedRecursionWalker
thought they could hold onto a pointer to a list's first
cons cell while the list was modified by recursive calls.
That was okay when the cons cell was actually separately
palloc'd ... but since commit 1cff1b95a, it's quite unsafe,
leading to core dumps or incorrect complaints of faulty
WITH nesting.
In the field this'd require at least a seven-deep WITH nest
to cause an issue, but enabling DEBUG_LIST_MEMORY_USAGE
allows the bug to be seen with lesser nesting depths.
Per bug #16801 from Alexander Lakhin. Back-patch to v13.
Michael Paquier and Tom Lane
Discussion: https://postgr.es/m/16801-393c7922143eaa4d@postgresql.org
Newline is certainly not a digit, nor a word character, so it is
sensible that it should match these complemented character classes.
Previously, \D and \W acted that way by default, but in
newline-sensitive mode ('n' or 'p' flag) they did not match newlines.
This behavior was previously forced because explicit complemented
character classes don't match newlines in newline-sensitive mode;
but as of the previous commit that implementation constraint no
longer exists. It seems useful to change this because the primary
real-world use for newline-sensitive mode seems to be to match the
default behavior of other regex engines such as Perl and Javascript
... and their default behavior is that these match newlines.
The old behavior can be kept by writing an explicit complemented
character class, i.e. [^[:digit:]] or [^[:word:]]. (This means
that \D and \W are not exactly equivalent to those strings, but
they weren't anyway.)
Discussion: https://postgr.es/m/3220564.1613859619@sss.pgh.pa.us
The complement-class escapes \D, \S, \W are now allowed within
bracket expressions. There is no semantic difficulty with doing
that, but the rather hokey macro-expansion-based implementation
previously used here couldn't cope.
Also, invent "word" as an allowed character class name, thus "\w"
is now equivalent to "[[:word:]]" outside brackets, or "[:word:]"
within brackets. POSIX allows such implementation-specific
extensions, and the same name is used in e.g. bash.
One surprising compatibility issue this raises is that constructs
such as "[\w-_]" are now disallowed, as our documentation has always
said they should be: character classes can't be endpoints of a range.
Previously, because \w was just a macro for "[:alnum:]_", such a
construct was read as "[[:alnum:]_-_]", so it was accepted so long as
the character after "-" was numerically greater than or equal to "_".
Some implementation cleanup along the way:
* Remove the lexnest() hack, and in consequence clean up wordchrs()
to not interact with the lexer.
* Fix colorcomplement() to not be O(N^2) in the number of colors
involved.
* Get rid of useless-as-far-as-I-can-see calls of element()
on single-character character element names in brackpart().
element() always maps these to the character itself, and things
would be quite broken if it didn't --- should "[a]" match something
different than "a" does? Besides, the shortcut path in brackpart()
wasn't doing this anyway, making it even more inconsistent.
Discussion: https://postgr.es/m/2845172.1613674385@sss.pgh.pa.us
Discussion: https://postgr.es/m/3220564.1613859619@sss.pgh.pa.us
Instead of an unsightly internal "cache lookup failed" message, just
return NULL for bad OIDs, as is the convention for other similar things.
Reported-by: Justin Pryzby <pryzby@telsasoft.com>
Reviewed-by: Michael Paquier <michael@paquier.xyz>
Discussion: https://postgr.es/m/20210117215940.GE8560%40telsasoft.com
For the error message "every hash partition modulus must be a factor
of the next larger modulus", add a detail message that shows the
particular numbers and existing partition involved. Also comment the
code more.
Reviewed-by: Amit Langote <amitlangote09@gmail.com>
Reviewed-by: Heikki Linnakangas <hlinnaka@iki.fi>
Discussion: https://www.postgresql.org/message-id/flat/bb9d60b4-aadb-607a-1a9d-fdc3434dddcd%40enterprisedb.com
This commit fixes COMMIT AND CHAIN command so that it starts new transaction
immediately even if savepoints are defined within the transaction to commit.
Previously COMMIT AND CHAIN command did not in that case because
commit 280a408b48 forgot to make CommitTransactionCommand() handle
a transaction chaining when the transaction state was TBLOCK_SUBCOMMIT.
Also this commit adds the regression test for COMMIT AND CHAIN command
when savepoints are defined.
Back-patch to v12 where transaction chaining was added.
Reported-by: Arthur Nascimento
Author: Fujii Masao
Reviewed-by: Arthur Nascimento, Vik Fearing
Discussion: https://postgr.es/m/16867-3475744069228158@postgresql.org
While poking at the regex code, I happened to notice that the bug
squashed in commit afcc8772e had a sibling: next() failed to return
a specific value associated with the '}' token for a "\{m,n\}"
quantifier when parsing in basic RE mode. Again, this could result
in treating the quantifier as non-greedy, which it never should be in
basic mode. For that to happen, the last character before "\}" that
sets "nextvalue" would have to set it to zero, or it'd have to have
accidentally been zero from the start. The failure can be provoked
repeatably with, for example, a bound ending in digit "0".
Like the previous patch, back-patch all the way.
Commit 2c8dd05d6c added the atomic variable writtenUpto into
walreceiver's shared memory information. It's initialized only
when walreceiver started up but could be read via pg_stat_wal_receiver
view anytime, i.e., even before it's initialized. In the server built
with --disable-atomics and --disable-spinlocks, this uninitialized
atomic variable read could cause "invalid spinlock number: 0" error.
This commit changed writtenUpto so that it's initialized at
the postmaster startup, to avoid the uninitialized variable read
via pg_stat_wal_receiver and fix the error.
Also this commit moved the read of writtenUpto after the release
of spinlock protecting walreceiver's shared variables. This is
necessary to prevent new spinlock from being taken by atomic
variable read while holding another spinlock, and to shorten
the spinlock duration. This change leads writtenUpto not to be
consistent with the other walreceiver's shared variables protected
by a spinlock. But this is OK because writtenUpto should not be
used for data integrity checks.
Back-patch to v13 where commit 2c8dd05d6c introduced the bug.
Author: Fujii Masao
Reviewed-by: Michael Paquier, Thomas Munro, Andres Freund
Discussion: https://postgr.es/m/7ef8708c-5b6b-edd3-2cf2-7783f1c7c175@oss.nttdata.com
Add another method to specify CRLs, hashed directory method, for both
server and client side. This offers a means for server or libpq to
load only CRLs that are required to verify a certificate. The CRL
directory is specifed by separate GUC variables or connection options
ssl_crl_dir and sslcrldir, alongside the existing ssl_crl_file and
sslcrl, so both methods can be used at the same time.
Author: Kyotaro Horiguchi <horikyota.ntt@gmail.com>
Discussion: https://www.postgresql.org/message-id/flat/20200731.173911.904649928639357911.horikyota.ntt@gmail.com
Push some hopefully-uncontroversial bits extracted from an upcoming
patch series, to remove non-relevant clutter from the main patches.
In compact(), return immediately after setting REG_ASSERT error;
continuing the loop would just lead to assertion failure below.
(Ask me how I know.)
In parseqatom(), remove assertion that moresubs() did its job.
When moresubs actually did its job, this is redundant with that
function's final assert; but when it failed on OOM, this is an
assertion crash. We could avoid the crash by adding a NOERR()
check before the assertion, but it seems better to subtract code
than add it. (Note that there's a NOERR exit a few lines further
down, and nothing else between here and there requires moresubs
to have succeeded. So we don't really need an extra error exit.)
This is a live bug in assert-enabled builds, but given the very
low likelihood of OOM in moresub's tiny allocation, I don't think
it's worth back-patching.
On the other hand, it seems worthwhile to add an assertion that
our intended v->subs[subno] target is still null by the time we
are ready to insert into it, since there's a recursion in between.
In pg_regexec, ensure we fflush any debug output on the way out,
and try to make MDEBUG messages more uniform and helpful. (In
particular, ensure that all of them are prefixed with the subre's
id number, so one can match up entry and exit reports.)
Add some test cases in test_regex to improve coverage of lookahead
and lookbehind constraints. Adding these now is mainly to establish
that this is indeed the existing behavior.
Discussion: https://postgr.es/m/1340281.1613018383@sss.pgh.pa.us
Several information schema views track dependencies between
functions/procedures and objects used by them. These had not been
implemented so far because PostgreSQL doesn't track objects used in a
function body. However, formally, these also show dependencies used
in parameter default expressions, which PostgreSQL does support and
track. So for the sake of completeness, we might as well add these.
If dependency tracking for function bodies is ever implemented, these
views will automatically work correctly.
Reviewed-by: Erik Rijkers <er@xs4all.nl>
Discussion: https://www.postgresql.org/message-id/flat/ac80fc74-e387-8950-9a31-2560778fc1e3%40enterprisedb.com
This issue exists from the inception of this code (PG-10) but got exposed
by the recent commit ce0fdbfe97 where we are using origins in tablesync
workers. The problem was that we were sometimes sending the prepare_write
('w') message but then the actual message was not being sent and on the
subscriber side, we always expect a message after prepare_write message
which led to this bug.
I refrained from backpatching this because there is no way in the core
code to hit this prior to commit ce0fdbfe97 and we haven't received any
complaints so far.
Reported-by: Erik Rijkers
Author: Amit Kapila and Vignesh C
Tested-by: Erik Rijkers
Discussion: https://postgr.es/m/1295168140.139428.1613133237154@webmailclassic.xs4all.nl
The inner loop in switchToPresortedPrefixMode() can be implemented
as a conventional integer-counter for() loop, removing a couple of
redundant boolean state variables. The old logic here was a remnant
of earlier development, but as things now stand there's no reason
for extra complexity.
Also, annotate the test case added by 82e0e2930 to explain why it
manages to hit the corner case fixed in that commit, and add an
EXPLAIN to verify that it's creating an incremental-sort plan.
Back-patch to v13, like the previous patch.
James Coleman and Tom Lane
Discussion: https://postgr.es/m/16846-ae49f51ac379a4cb@postgresql.org
This commit adds new column "waitstart" into pg_locks view. This column
reports the time when the server process started waiting for the lock
if the lock is not held. This information is useful, for example, when
examining the amount of time to wait on a lock by subtracting
"waitstart" in pg_locks from the current time, and identify the lock
that the processes are waiting for very long.
This feature uses the current time obtained for the deadlock timeout
timer as "waitstart" (i.e., the time when this process started waiting
for the lock). Since getting the current time newly can cause overhead,
we reuse the already-obtained time to avoid that overhead.
Note that "waitstart" is updated without holding the lock table's
partition lock, to avoid the overhead by additional lock acquisition.
This can cause "waitstart" in pg_locks to become NULL for a very short
period of time after the wait started even though "granted" is false.
This is OK in practice because we can assume that users are likely to
look at "waitstart" when waiting for the lock for a long time.
The first attempt of this patch (commit 3b733fcd04) caused the buildfarm
member "rorqual" (built with --disable-atomics --disable-spinlocks) to report
the failure of the regression test. It was reverted by commit 890d2182a2.
The cause of this failure was that the atomic variable for "waitstart"
in the dummy process entry created at the end of prepare transaction was
not initialized. This second attempt fixes that issue.
Bump catalog version.
Author: Atsushi Torikoshi
Reviewed-by: Ian Lawrence Barwick, Robert Haas, Justin Pryzby, Fujii Masao
Discussion: https://postgr.es/m/a96013dc51cdc56b2a2b84fa8a16a993@oss.nttdata.com
We want to test the variants of Alter Subscription that are not allowed in
the transaction block but for that, we don't need to create a subscription
that tries to connect to the publisher. As such, there is no problem with
this test but it is good to allow such tests to run with
wal_level = minimal and max_wal_senders = 0 so as to keep them consistent
with other tests.
Reported by buildfarm.
Author: Amit Kapila
Reviewed-by: Ajin Cherian
Discussion: https://postgr.es/m/CAA4eK1Lw0V+e1JPGHDq=+hVACv=14H8sR+2eJ1k3PEgwKmU-jQ@mail.gmail.com
For the initial table data synchronization in logical replication, we use
a single transaction to copy the entire table and then synchronize the
position in the stream with the main apply worker.
There are multiple downsides of this approach: (a) We have to perform the
entire copy operation again if there is any error (network breakdown,
error in the database operation, etc.) while we synchronize the WAL
position between tablesync worker and apply worker; this will be onerous
especially for large copies, (b) Using a single transaction in the
synchronization-phase (where we can receive WAL from multiple
transactions) will have the risk of exceeding the CID limit, (c) The slot
will hold the WAL till the entire sync is complete because we never commit
till the end.
This patch solves all the above downsides by allowing multiple
transactions during the tablesync phase. The initial copy is done in a
single transaction and after that, we commit each transaction as we
receive. To allow recovery after any error or crash, we use a permanent
slot and origin to track the progress. The slot and origin will be removed
once we finish the synchronization of the table. We also remove slot and
origin of tablesync workers if the user performs DROP SUBSCRIPTION .. or
ALTER SUBSCRIPTION .. REFERESH and some of the table syncs are still not
finished.
The commands ALTER SUBSCRIPTION ... REFRESH PUBLICATION and
ALTER SUBSCRIPTION ... SET PUBLICATION ... with refresh option as true
cannot be executed inside a transaction block because they can now drop
the slots for which we have no provision to rollback.
This will also open up the path for logical replication of 2PC
transactions on the subscriber side. Previously, we can't do that because
of the requirement of maintaining a single transaction in tablesync
workers.
Bump catalog version due to change of state in the catalog
(pg_subscription_rel).
Author: Peter Smith, Amit Kapila, and Takamichi Osumi
Reviewed-by: Ajin Cherian, Petr Jelinek, Hou Zhijie and Amit Kapila
Discussion: https://postgr.es/m/CAA4eK1KHJxaZS-fod-0fey=0tq3=Gkn4ho=8N4-5HWiCfu0H1A@mail.gmail.com
For an index, attstattarget can be updated using ALTER INDEX SET
STATISTICS. This data was lost on the new index after REINDEX
CONCURRENTLY.
The update of this field is done when the old and new indexes are
swapped to make the fix back-patchable. Another approach we could look
after in the long-term is to change index_create() to pass the wanted
values of attstattarget when creating the new relation, but, as this
would cause an ABI breakage this can be done only on HEAD.
Reported-by: Ronan Dunklau
Author: Michael Paquier
Reviewed-by: Ronan Dunklau, Tomas Vondra
Discussion: https://postgr.es/m/16628084.uLZWGnKmhe@laptop-ronand
Backpatch-through: 12
This commit adds new column "waitstart" into pg_locks view. This column
reports the time when the server process started waiting for the lock
if the lock is not held. This information is useful, for example, when
examining the amount of time to wait on a lock by subtracting
"waitstart" in pg_locks from the current time, and identify the lock
that the processes are waiting for very long.
This feature uses the current time obtained for the deadlock timeout
timer as "waitstart" (i.e., the time when this process started waiting
for the lock). Since getting the current time newly can cause overhead,
we reuse the already-obtained time to avoid that overhead.
Note that "waitstart" is updated without holding the lock table's
partition lock, to avoid the overhead by additional lock acquisition.
This can cause "waitstart" in pg_locks to become NULL for a very short
period of time after the wait started even though "granted" is false.
This is OK in practice because we can assume that users are likely to
look at "waitstart" when waiting for the lock for a long time.
Bump catalog version.
Author: Atsushi Torikoshi
Reviewed-by: Ian Lawrence Barwick, Robert Haas, Justin Pryzby, Fujii Masao
Discussion: https://postgr.es/m/a96013dc51cdc56b2a2b84fa8a16a993@oss.nttdata.com
This option controls if toast tables associated with a relation are
vacuumed or not when running a manual VACUUM. It was already possible
to trigger a manual VACUUM on a toast relation without processing its
main relation, but a manual vacuum on a main relation always forced a
vacuum on its toast table. This is useful in scenarios where the level
of bloat or transaction age of the main and toast relations differs a
lot.
This option is an extension of the existing VACOPT_SKIPTOAST that was
used by autovacuum to control if toast relations should be skipped or
not. This internal flag is renamed to VACOPT_PROCESS_TOAST for
consistency with the new option.
A new option switch, called --no-process-toast, is added to vacuumdb.
Author: Nathan Bossart
Reviewed-by: Kirk Jamison, Michael Paquier, Justin Pryzby
Discussion: https://postgr.es/m/BA8951E9-1524-48C5-94AF-73B1F0D7857F@amazon.com
scanNSItemForColumn, expandNSItemAttrs, and ExpandSingleTable would
pass the wrong RTE to markVarForSelectPriv when dealing with a join
ParseNamespaceItem: they'd pass the join RTE, when what we need to
mark is the base table that the join column came from. The end
result was to not fill the base table's selectedCols bitmap correctly,
resulting in an understatement of the set of columns that are read
by the query. The executor would still insist on there being at
least one selectable column; but with a correctly crafted query,
a user having SELECT privilege on just one column of a table would
nonetheless be allowed to read all its columns.
To fix, make markRTEForSelectPriv fetch the correct RTE for itself,
ignoring the possibly-mismatched RTE passed by the caller. Later,
we'll get rid of some now-unused RTE arguments, but that risks
API breaks so we won't do it in released branches.
This problem was introduced by commit 9ce77d75c, so back-patch
to v13 where that came in. Thanks to Sven Klemm for reporting
the problem.
Security: CVE-2021-20229
If a cross-partition UPDATE violates a constraint on the target partition,
and the columns in the new partition are in different physical order than
in the parent, the error message can reveal columns that the user does not
have SELECT permission on. A similar bug was fixed earlier in commit
804b6b6db4.
The cause of the bug is that the callers of the
ExecBuildSlotValueDescription() function got confused when constructing
the list of modified columns. If the tuple was routed from a parent, we
converted the tuple to the parent's format, but the list of modified
columns was grabbed directly from the child's RTE entry.
ExecUpdateLockMode() had a similar issue. That lead to confusion on which
columns are key columns, leading to wrong tuple lock being taken on tables
referenced by foreign keys, when a row is updated with INSERT ON CONFLICT
UPDATE. A new isolation test is added for that corner case.
With this patch, the ri_RangeTableIndex field is no longer set for
partitions that don't have an entry in the range table. Previously, it was
set to the RTE entry of the parent relation, but that was confusing.
NOTE: This modifies the ResultRelInfo struct, replacing the
ri_PartitionRoot field with ri_RootResultRelInfo. That's a bit risky to
backpatch, because it breaks any extensions accessing the field. The
change that ri_RangeTableIndex is not set for partitions could potentially
break extensions, too. The ResultRelInfos are visible to FDWs at least,
and this patch required small changes to postgres_fdw. Nevertheless, this
seem like the least bad option. I don't think these fields widely used in
extensions; I don't think there are FDWs out there that uses the FDW
"direct update" API, other than postgres_fdw. If there is, you will get a
compilation error, so hopefully it is caught quickly.
Backpatch to 11, where support for both cross-partition UPDATEs, and unique
indexes on partitioned tables, were added.
Reviewed-by: Amit Langote
Security: CVE-2021-3393
rewriteRuleAction() neglected this step, although it was careful to
propagate other similar flags such as hasSubLinks or hasRowSecurity.
Omitting to transfer hasRecursive is just cosmetic at the moment,
but omitting hasModifyingCTE is a live bug, since the executor
certainly looks at that.
The proposed test case only fails back to v10, but since the executor
examines hasModifyingCTE in 9.x as well, I suspect that a test case
could be devised that fails in older branches. Given the nearness
of the release deadline, though, I'm not going to spend time looking
for a better test.
Report and patch by Greg Nancarrow, cosmetic changes by me
Discussion: https://postgr.es/m/CAJcOf-fAdj=nDKMsRhQzndm-O13NY4dL6xGcEvdX5Xvbbi0V7g@mail.gmail.com
Generally, members of inheritance trees must be plain tables (or,
in more recent versions, foreign tables). ALTER TABLE INHERIT
rejects creating an inheritance relationship that has a view at
either end. When DefineQueryRewrite attempts to convert a relation
to a view, it already had checks prohibiting doing so for partitioning
parents or children as well as traditional-inheritance parents ...
but it neglected to check that a traditional-inheritance child wasn't
being converted. Since the planner assumes that any inheritance
child is a table, this led to making plans that tried to do a physical
scan on a view, causing failures (or even crashes, in recent versions).
One could imagine trying to support such a case by expanding the view
normally, but since the rewriter runs before the planner does
inheritance expansion, it would take some very fundamental refactoring
to make that possible. There are probably a lot of other parts of the
system that don't cope well with such a situation, too. For now,
just forbid it.
Per bug #16856 from Yang Lin. Back-patch to all supported branches.
(In versions before v10, this includes back-patching the portion of
commit 501ed02cf that added has_superclass(). Perhaps the lack of
that infrastructure partially explains the missing check.)
Discussion: https://postgr.es/m/16856-0363e05c6e1612fd@postgresql.org
switchToPresortedPrefixMode() did the wrong thing if it detected
a batch boundary just at the last tuple of a fullsort group.
The initially-reported symptom was a "retrieved too many tuples in a
bounded sort" error, but the test case added here just silently gives
the wrong answer without this patch.
I (tgl) am not really happy about committing this patch without review
from the incremental-sort authors, but they seem AWOL and we are hard
against a release deadline. This does demonstrably make some cases
better, anyway.
Per bug #16846 from Yoran Heling. Back-patch to v13 where incremental
sort was introduced.
Neil Chen
Discussion: https://postgr.es/m/16846-ae49f51ac379a4cb@postgresql.org
This patch adds the possibility to move indexes to a new tablespace
while rebuilding them. Both the concurrent and the non-concurrent cases
are supported, and the following set of restrictions apply:
- When using TABLESPACE with a REINDEX command that targets a
partitioned table or index, all the indexes of the leaf partitions are
moved to the new tablespace. The tablespace references of the non-leaf,
partitioned tables in pg_class.reltablespace are not changed. This
requires an extra ALTER TABLE SET TABLESPACE.
- Any index on a toast table rebuilt as part of a parent table is kept
in its original tablespace.
- The operation is forbidden on system catalogs, including trying to
directly move a toast relation with REINDEX. This results in an error
if doing REINDEX on a single object. REINDEX SCHEMA, DATABASE and
SYSTEM skip system relations when TABLESPACE is used.
Author: Alexey Kondratov, Michael Paquier, Justin Pryzby
Reviewed-by: Álvaro Herrera, Michael Paquier
Discussion: https://postgr.es/m/8a8f5f73-00d3-55f8-7583-1375ca8f6a91@postgrespro.ru
This follows in the spirit of commit dfb75e478, which created primary
key and uniqueness constraints to improve the visibility of constraints
imposed on the system catalogs. While our catalogs contain many
foreign-key-like relationships, they don't quite follow SQL semantics,
in that the convention for an omitted reference is to write zero not
NULL. Plus, we have some cases in which there are arrays each of whose
elements is supposed to be an FK reference; SQL has no way to model that.
So we can't create actual foreign key constraints to describe the
situation. Nonetheless, we can collect and use knowledge about these
relationships.
This patch therefore adds annotations to the catalog header files to
declare foreign-key relationships. (The BKI_LOOKUP annotations cover
simple cases, but we weren't previously distinguishing which such
columns are allowed to contain zeroes; we also need new markings for
multi-column FK references.) Then, Catalog.pm and genbki.pl are
taught to collect this information into a table in a new generated
header "system_fk_info.h". The only user of that at the moment is
a new SQL function pg_get_catalog_foreign_keys(), which exposes the
table to SQL. The oidjoins regression test is rewritten to use
pg_get_catalog_foreign_keys() to find out which columns to check.
Aside from removing the need for manual maintenance of that test
script, this allows it to cover numerous relationships that were not
checked by the old implementation based on findoidjoins. (As of this
commit, 217 relationships are checked by the test, versus 181 before.)
Discussion: https://postgr.es/m/3240355.1612129197@sss.pgh.pa.us
This adds the SQL standard feature that adds the SEARCH and CYCLE
clauses to recursive queries to be able to do produce breadth- or
depth-first search orders and detect cycles. These clauses can be
rewritten into queries using existing syntax, and that is what this
patch does in the rewriter.
Reviewed-by: Vik Fearing <vik@postgresfriends.org>
Reviewed-by: Pavel Stehule <pavel.stehule@gmail.com>
Discussion: https://www.postgresql.org/message-id/flat/db80ceee-6f97-9b4a-8ee8-3ba0c58e5be2@2ndquadrant.com
This is a replacement for the existing --with-openssl, extending the
logic to make easier the addition of new SSL libraries. The grammar is
chosen to be similar to --with-uuid, where multiple values can be
chosen, with "openssl" as the only supported value for now.
The original switch, --with-openssl, is kept for compatibility.
Author: Daniel Gustafsson, Michael Paquier
Reviewed-by: Jacob Champion
Discussion: https://postgr.es/m/FAB21FC8-0F62-434F-AA78-6BD9336D630A@yesql.se
When to_tsquery() or websearch_to_tsquery() meet a complex morph containing
multiple words residing adjacent position, these words are connected
with OP_AND operator. That leads to surprising results. For instace,
both websearch_to_tsquery('"pg_class pg"') and to_tsquery('pg_class <-> pg')
produce '( pg & class ) <-> pg' tsquery. This tsquery requires
'pg' and 'class' words to reside on the same position and doesn't match
to to_tsvector('pg_class pg'). It appears to be ridiculous behavior, which
needs to be fixed.
This commit makes to_tsquery() or websearch_to_tsquery() connect words
residing adjacent position with OP_PHRASE. Therefore, now those words are
normally chained with other OP_PHRASE operator. The examples of above now
produces 'pg <-> class <-> pg' tsquery, which matches to
to_tsvector('pg_class pg').
Another effect of this commit is that complex morph word positions now need to
match the tsvector even if there is no surrounding OP_PHRASE. This behavior
change generally looks like an improvement but making this commit not
backpatchable.
Reported-by: Barry Pederson
Bug: #16592
Discussion: https://postgr.es/m/16592-70b110ff9731c07d@postgresql.org
Discussion: https://postgr.es/m/CAPpHfdv0EzVhf6CWfB1_TTZqXV_2Sn-jSY3zSd7ePH%3D-%2B1V2DQ%40mail.gmail.com
Author: Alexander Korotkov
Reviewed-by: Tom Lane, Neil Chen
For those system catalogs that have a unique indexes, make a primary
key and unique constraint, using ALTER TABLE ... PRIMARY KEY/UNIQUE
USING INDEX.
This can be helpful for GUI tools that look for a primary key, and it
might in the future allow declaring foreign keys, for making schema
diagrams.
The constraint creation statements are automatically created by
genbki.pl from DECLARE_UNIQUE_INDEX directives. To specify which one
of the available unique indexes is the primary key, use the new
directive DECLARE_UNIQUE_INDEX_PKEY instead. By convention, we
usually make a catalog's OID column its primary key, if it has one.
Reviewed-by: Tom Lane <tgl@sss.pgh.pa.us>
Discussion: https://www.postgresql.org/message-id/flat/dc5f44d9-5ec1-a596-0251-dadadcdede98@2ndquadrant.com
The SQL standard allows a GRANTED BY clause on GRANT and
REVOKE (privilege) statements that can specify CURRENT_USER or
CURRENT_ROLE. In PostgreSQL, both of these are the default behavior.
Since we already have all the parsing support for this for the
GRANT (role) statement, we might as well add basic support for this
for the privilege variant as well. This allows us to check off SQL
feature T332. In the future, perhaps more interesting things could be
done with this, too.
Reviewed-by: Simon Riggs <simon@2ndquadrant.com>
Discussion: https://www.postgresql.org/message-id/flat/f2feac44-b4c5-f38f-3699-2851d6a76dc9@2ndquadrant.com
CREATE PUBLICATION has failed spuriously when applied to a permanent
relation created or rewritten in the current transaction. Make the same
change to another site having the same semantic intent; the second
instance has no user-visible consequences. Back-patch to v13, where
commit c6b92041d3 broke this.
Kyotaro Horiguchi
Discussion: https://postgr.es/m/20210113.160705.2225256954956139776.horikyota.ntt@gmail.com
In a cluster having used CREATE INDEX CONCURRENTLY while having enabled
prepared transactions, queries that use the resulting index can silently
fail to find rows. Fix this for future CREATE INDEX CONCURRENTLY by
making it wait for prepared transactions like it waits for ordinary
transactions. This expands the VirtualTransactionId structure domain to
admit prepared transactions. It may be necessary to reindex to recover
from past occurrences. Back-patch to 9.5 (all supported versions).
Andrey Borodin, reviewed (in earlier versions) by Tom Lane and Michael
Paquier.
Discussion: https://postgr.es/m/2E712143-97F7-4890-B470-4A35142ABC82@yandex-team.ru
In trying to protect the user from inconsistent behavior, commit
487e9861d0 "Enable BEFORE row-level triggers for partitioned tables"
tried to prevent BEFORE UPDATE FOR EACH ROW triggers from moving the row
from one partition to another. However, it turns out that the
restriction is wrong in two ways: first, it fails spuriously, preventing
valid situations from working, as in bug #16794; and second, they don't
protect from any misbehavior, because tuple routing would cope anyway.
Fix by removing that restriction.
We keep the same restriction on BEFORE INSERT FOR EACH ROW triggers,
though. It is valid and useful there. In the future we could remove it
by having tuple reroute work for inserts as it does for updates.
Backpatch to 13.
Author: Álvaro Herrera <alvherre@alvh.no-ip.org>
Reported-by: Phillip Menke <pg@pmenke.de>
Discussion: https://postgr.es/m/16794-350a655580fbb9ae@postgresql.org
perform_pruning_combine_step() was not taught about the number of
partition indexes used in hash partitioning; more embarrassingly,
get_matching_hash_bounds() also had it wrong. These errors are masked
in the common case where all the partitions have the same modulus
and no partition is missing. However, with missing or unequal-size
partitions, we could erroneously prune some partitions that need
to be scanned, leading to silently wrong query answers.
While a minimal-footprint fix for this could be to export
get_partition_bound_num_indexes and make the incorrect functions use it,
I'm of the opinion that that function should never have existed in the
first place. It's not reasonable data structure design that
PartitionBoundInfoData lacks any explicit record of the length of
its indexes[] array. Perhaps that was all right when it could always
be assumed equal to ndatums, but something should have been done about
it as soon as that stopped being true. Putting in an explicit
"nindexes" field makes both partition_bounds_equal() and
partition_bounds_copy() simpler, safer, and faster than before,
and removes explicit knowledge of the number-of-partition-indexes
rules from some other places too.
This change also makes get_hash_partition_greatest_modulus obsolete.
I left that in place in case any external code uses it, but no core
code does anymore.
Per bug #16840 from Michał Albrycht. Back-patch to v11 where the
hash partitioning code came in. (In the back branches, add the new
field at the end of PartitionBoundInfoData to minimize ABI risks.)
Discussion: https://postgr.es/m/16840-571a22976f829ad4@postgresql.org
CREATE TABLE AS has been preferred over SELECT INTO (outside of ecpg
and PL/pgSQL) for a long time. There were still a few uses of SELECT
INTO in tests and documentation, some old, some more recent. This
changes them to CREATE TABLE AS. Some occurrences in the tests remain
where they are specifically testing SELECT INTO parsing or similar.
Discussion: https://www.postgresql.org/message-id/flat/96dc0df3-e13a-a85d-d045-d6e2c85218da%40enterprisedb.com
Commit 69bd60672 fixed the initialization of streamed transactions for
RelationSyncEntry. It forgot to initialize the publication actions while
invalidating the RelationSyncEntry due to which even though the relation
is dropped from a particular publication we still publish its changes. Fix
it by initializing pubactions when entry got invalidated.
Author: Japin Li and Bharath Rupireddy
Reviewed-by: Amit Kapila
Discussion: https://postgr.es/m/CALj2ACV+0UFpcZs5czYgBpujM9p0Hg1qdOZai_43OU7bqHU_xw@mail.gmail.com
libpq's error messages for connection failures pretty well stand on
their own, especially since commits 52a10224e/27a48e5a1. Prefixing
them with 'could not connect to database "foo"' or the like is just
redundant, and perhaps even misleading if the specific database name
isn't relevant to the failure. (When it is, we trust that the
backend's error message will include the DB name.) Indeed, psql
hasn't used any such prefix in a long time. So, make all our other
programs and documentation examples agree with psql's practice.
Discussion: https://postgr.es/m/1094524.1611266589@sss.pgh.pa.us
Previously, pull_varnos() took the relids of a PlaceHolderVar as being
equal to the relids in its contents, but that fails to account for the
possibility that we have to postpone evaluation of the PHV due to outer
joins. This could result in a malformed plan. The known cases end up
triggering the "failed to assign all NestLoopParams to plan nodes"
sanity check in createplan.c, but other symptoms may be possible.
The right value to use is the join level we actually intend to evaluate
the PHV at. We can get that from the ph_eval_at field of the associated
PlaceHolderInfo. However, there are some places that call pull_varnos()
before the PlaceHolderInfos have been created; in that case, fall back
to the conservative assumption that the PHV will be evaluated at its
syntactic level. (In principle this might result in missing some legal
optimization, but I'm not aware of any cases where it's an issue in
practice.) Things are also a bit ticklish for calls occurring during
deconstruct_jointree(), but AFAICS the ph_eval_at fields should have
reached their final values by the time we need them.
The main problem in making this work is that pull_varnos() has no
way to get at the PlaceHolderInfos. We can fix that easily, if a
bit tediously, in HEAD by passing it the planner "root" pointer.
In the back branches that'd cause an unacceptable API/ABI break for
extensions, so leave the existing entry points alone and add new ones
with the additional parameter. (If an old entry point is called and
encounters a PHV, it'll fall back to using the syntactic level,
again possibly missing some valid optimization.)
Back-patch to v12. The computation is surely also wrong before that,
but it appears that we cannot reach a bad plan thanks to join order
restrictions imposed on the subquery that the PlaceHolderVar came from.
The error only became reachable when commit 4be058fe9 allowed trivial
subqueries to be collapsed out completely, eliminating their join order
restrictions.
Per report from Stephan Springl.
Discussion: https://postgr.es/m/171041.1610849523@sss.pgh.pa.us
The new command lists extended statistics objects. All past releases
with extended statistics are supported.
This is a simplified version of commit 891a1d0bca, which had to be
reverted due to not considering pg_statistic_ext_data is not accessible
by regular users. Fields requiring access to this catalog were removed.
It's possible to add them, but it'll require changes to core.
Author: Tatsuro Yamada
Reviewed-by: Julien Rouhaud, Alvaro Herrera, Tomas Vondra, Noriyoshi Shinoda
Discussion: https://postgr.es/m/c027a541-5856-75a5-0868-341301e1624b%40nttcom.co.jp_1
DROP OWNED BY has a specific code path to remove ACLs stored in
pg_default_acl when cleaning up shared dependencies that had no
coverage with the existing tests. This issue has been found while
digging into the bug fixed by 21378e1.
As ALTER DEFAULT PRIVILEGES impacts the ACLs of all objects created
while the default permissions are visible, the test uses a transaction
rollback to isolate the test and avoid any impact with other sessions
running in parallel.
Reviewed-by: Álvaro Herrera
Discussion: https://postgr.es/m/YAbQ1OD+3ip4lRv8@paquier.xyz
Specifying duplicated objects in this command would lead to unique
constraint violations in pg_default_acl or "tuple already updated by
self" errors. Similarly to GRANT/REVOKE, increment the command ID after
each subcommand processing to allow this case to work transparently.
A regression test is added by tweaking one of the existing queries of
privileges.sql to stress this case.
Reported-by: Andrus
Author: Michael Paquier
Reviewed-by: Álvaro Herrera
Discussion: https://postgr.es/m/ae2a7dc1-9d71-8cba-3bb9-e4cb7eb1f44e@hot.ee
Backpatch-through: 9.5
The stanza to report a "partial" match could overrun the initially
allocated output array, so it needs its own copy of the array-resizing
logic that's in the main loop. I overlooked the need for this in
ca8217c10.
Per report from Alexander Lakhin.
Discussion: https://postgr.es/m/3206aace-50db-e02a-bbea-76d5cdaa2cb6@gmail.com
This add counters for number of sessions, the different kind of session
termination types, and timers for how much time is spent in active vs
idle in a database to pg_stat_database.
Internally this also renames the parameter "force" to disconnect. This
was the only use-case for the parameter before, so repurposing it to
this mroe narrow usecase makes things cleaner than inventing something
new.
Author: Laurenz Albe
Reviewed-By: Magnus Hagander, Soumyadeep Chakraborty, Masahiro Ikeda
Discussion: https://postgr.es/m/b07e1f9953701b90c66ed368656f2aef40cac4fb.camel@cybertec.at
The new command lists extended statistics objects, possibly with their
sizes. All past releases with extended statistics are supported.
Author: Tatsuro Yamada
Reviewed-by: Julien Rouhaud, Alvaro Herrera, Tomas Vondra
Discussion: https://postgr.es/m/c027a541-5856-75a5-0868-341301e1624b%40nttcom.co.jp_1
The context is an object that no longer bears some aclitem that it bore
initially. (A user issued REVOKE or GRANT statements upon the object.)
pg_dump is forming SQL to reproduce the object ACL. Since initdb
creates no ACL bearing GRANT OPTION, reaching this bug requires an
extension where the creation script establishes such an ACL. No PGXN
extension does that. If an installation did reach the bug, pg_dump
would have omitted a semicolon, causing a REVOKE and the next SQL
statement to fail. Separately, since the affected code exists to
eliminate an entire aclitem, it wants plain REVOKE, not REVOKE GRANT
OPTION FOR. Back-patch to 9.6, where commit
23f34fa4ba first appeared.
Discussion: https://postgr.es/m/20210109102423.GA160022@rfd.leadboat.com
Add a check that CREATE STATISTICS does not add extended statistics on
system catalogs, similarly to indexes etc. It can be overriden using
the allow_system_table_mods GUC.
This bug exists since 7b504eb282, adding the extended statistics, so
backpatch all the way back to PostgreSQL 10.
Author: Tomas Vondra
Reported-by: Dean Rasheed
Backpatch-through: 10
Discussion: https://postgr.es/m/CAEZATCXAPrrOKwEsyZKQ4uzzJQWBCt6QAvOcgqRGdWwT1zb%2BrQ%40mail.gmail.com
When a tablespace is used in a partitioned relation (per commits
ca4103025d in pg12 for tables and 33e6c34c32 in pg11 for indexes),
it is possible to drop the tablespace, potentially causing various
problems. One such was reported in bug #16577, where a rewriting ALTER
TABLE causes a server crash.
Protect against this by using pg_shdepend to keep track of tablespaces
when used for relations that don't keep physical files; we now abort a
tablespace if we see that the tablespace is referenced from any
partitioned relations.
Backpatch this to 11, where this problem has been latent all along. We
don't try to create pg_shdepend entries for existing partitioned
indexes/tables, but any ones that are modified going forward will be
protected.
Note slight behavior change: when trying to drop a tablespace that
contains both regular tables as well as partitioned ones, you'd
previously get ERRCODE_OBJECT_NOT_IN_PREREQUISITE_STATE and now you'll
get ERRCODE_DEPENDENT_OBJECTS_STILL_EXIST. Arguably, the latter is more
correct.
It is possible to add protecting pg_shdepend entries for existing
tables/indexes, by doing
ALTER TABLE ONLY some_partitioned_table SET TABLESPACE pg_default;
ALTER TABLE ONLY some_partitioned_table SET TABLESPACE original_tablespace;
for each partitioned table/index that is not in the database default
tablespace. Because these partitioned objects do not have storage, no
file needs to be actually moved, so it shouldn't take more time than
what's required to acquire locks.
This query can be used to search for such relations:
SELECT ... FROM pg_class WHERE relkind IN ('p', 'I') AND reltablespace <> 0
Reported-by: Alexander Lakhin <exclusion@gmail.com>
Discussion: https://postgr.es/m/16577-881633a9f9894fd5@postgresql.org
Author: Álvaro Herrera <alvherre@alvh.no-ip.org>
Reviewed-by: Michael Paquier <michael@paquier.xyz>
Commit fef5b47f6b added the regression test to check whether a standby is
able to follow a primary on a newer timeline when WAL archiving is enabled.
But the buildfarm member florican reported that this test failed because
the requested WAL segment was removed and replication failed. This is a
timing issue. Since neither replication slot is used nor wal_keep_size is set
in the test, checkpoint could remove the WAL segment that's still necessary
for replication.
This commit stabilizes the test by setting wal_keep_size.
Back-patch to v13 where the regression test that this commit stabilizes
was added.
Author: Fujii Masao
Discussion: https://postgr.es/m/X//PsenxcC50jDzX@paquier.xyz
Commit 709d003fbd refactored WAL-reading code, but accidentally caused
WalSndSegmentOpen() to fail to follow a timeline switch while reading from
a historic timeline. This issue caused a standby to fail to follow a primary
on a newer timeline when WAL archiving is enabled.
If there is a timeline switch within the segment, WalSndSegmentOpen() should
read from the WAL segment belonging to the new timeline. But previously
since it failed to follow a timeline switch, it tried to read the WAL segment
with old timeline. When WAL archiving is enabled, that WAL segment with
old timeline doesn't exist because it's renamed to .partial. This leads
a primary to have tried to read non-existent WAL segment, and which caused
replication to faill with the error "ERROR: requested WAL segment ... has
already been removed".
This commit fixes WalSndSegmentOpen() so that it's able to follow a timeline
switch, to ensure that a standby is able to follow a primary on a newer
timeline even when WAL archiving is enabled.
This commit also adds the regression test to check whether a standby is
able to follow a primary on a newer timeline when WAL archiving is enabled.
Back-patch to v13 where the bug was introduced.
Reported-by: Kyotaro Horiguchi
Author: Kyotaro Horiguchi, tweaked by Fujii Masao
Reviewed-by: Alvaro Herrera, Fujii Masao
Discussion: https://postgr.es/m/20201209.174314.282492377848029776.horikyota.ntt@gmail.com
Add an executor aminsert() hint mechanism that informs index AMs that
the incoming index tuple (the tuple that accompanies the hint) is not
being inserted by execution of an SQL statement that logically modifies
any of the index's key columns.
The hint is received by indexes when an UPDATE takes place that does not
apply an optimization like heapam's HOT (though only for indexes where
all key columns are logically unchanged). Any index tuple that receives
the hint on insert is expected to be a duplicate of at least one
existing older version that is needed for the same logical row. Related
versions will typically be stored on the same index page, at least
within index AMs that apply the hint.
Recognizing the difference between MVCC version churn duplicates and
true logical row duplicates at the index AM level can help with cleanup
of garbage index tuples. Cleanup can intelligently target tuples that
are likely to be garbage, without wasting too many cycles on less
promising tuples/pages (index pages with little or no version churn).
This is infrastructure for an upcoming commit that will teach nbtree to
perform bottom-up index deletion. No index AM actually applies the hint
just yet.
Author: Peter Geoghegan <pg@bowt.ie>
Reviewed-By: Victor Yegorov <vyegorov@gmail.com>
Discussion: https://postgr.es/m/CAH2-Wz=CEKFa74EScx_hFVshCOn6AA5T-ajFASTdzipdkLTNQQ@mail.gmail.com
Add an optional callback to regression_main() that, if provided,
is invoked on each test output file before we try to compare it
to the expected-result file.
The main and isolation test programs don't need this (yet).
In pg_regress_ecpg, add a filter that eliminates target-host
details from "could not connect" error reports. This filter
doesn't do anything as of this commit, but it will be needed
by the next one.
In the long run we might want to provide some more general,
perhaps pattern-based, filtering mechanism for test output.
For now, this will solve the immediate problem.
Discussion: https://postgr.es/m/BN6PR05MB3492948E4FD76C156E747E8BC9160@BN6PR05MB3492.namprd05.prod.outlook.com
brenext(), when parsing a '*' quantifier, forgot to return any "value"
for the token; per the equivalent case in next(), it should return
value 1 to indicate that greedy rather than non-greedy behavior is
wanted. The result is that the compiled regexp could behave like 'x*?'
rather than the intended 'x*', if we were unlucky enough to have
a zero in v->nextvalue at this point. That seems to happen with some
reliability if we have '.*' at the beginning of a BRE-mode regexp,
although that depends on the initial contents of a stack-allocated
struct, so it's not guaranteed to fail.
Found by Alexander Lakhin using valgrind testing. This bug seems
to be aboriginal in Spencer's code, so back-patch all the way.
Discussion: https://postgr.es/m/16814-6c5e3edd2bdf0d50@postgresql.org
This module provides a function test_regex() that is functionally
rather like regexp_matches(), but with additional debugging-oriented
options and additional output. The debug options are somewhat obscure;
they are chosen to match the API of the test harness that Henry Spencer
wrote way-back-when for use in Tcl. With this, we can import all the
test cases that Spencer wrote originally, even for regex functionality
that we don't currently expose in Postgres. This seems necessary
because we can no longer rely on Tcl to act as upstream and verify
any fixes or improvements that we make.
In addition to Spencer's tests, I added a few for lookbehind
constraints (which we added in 2015, and Tcl still hasn't absorbed)
that are modeled on his tests for lookahead constraints. After looking
at code coverage reports, I also threw in a couple of tests to more
fully exercise our "high colormap" logic.
According to my testing, this brings the check-world coverage
for src/backend/regex/ from 71.1% to 86.7% of lines.
(coverage.postgresql.org shows a slightly different number,
which I think is because it measures a non-assert build.)
Discussion: https://postgr.es/m/2873268.1609732164@sss.pgh.pa.us
Formerly, TOAST objects were unconditionally suppressed, but since
\d is able to print them it's not very clear why these variants
should not. Instead, use the same rules as for system catalogs:
they can be seen if you write the 'S' modifier or a table name
pattern. (In practice, since hardly anybody would keep pg_toast
in their search_path, it's really down to whether you use a pattern
that can match pg_toast.*.)
No docs change seems necessary because the docs already say that
this happens for "system objects"; we're just classifying TOAST
tables as being that.
Justin Pryzby, reviewed by Laurenz Albe
Discussion: https://postgr.es/m/20201130165436.GX24052@telsasoft.com
In power_var_int(), the computation of the number of significant
digits to use in the computation used log(Abs(exp)), which isn't safe
because Abs(exp) returns INT_MIN when exp is INT_MIN. Use fabs()
instead of Abs(), so that the exponent is cast to a double before the
absolute value is taken.
Back-patch to 9.6, where this was introduced (by 7d9a4737c2).
Discussion: https://postgr.es/m/CAEZATCVd6pMkz=BrZEgBKyqqJrt2xghr=fNc8+Z=5xC6cgWrWA@mail.gmail.com
If the substring start index and length overflow when added together,
substring() misbehaved, either throwing a bogus "negative substring
length" error on a case that should succeed, or failing to complain that
a negative length is negative (and instead returning the whole string,
in most cases). Unsurprisingly, the text, bytea, and bit variants of
the function all had this issue. Rearrange the logic to ensure that
negative lengths are always rejected, and add an overflow check to
handle the other case.
Also install similar guards into detoast_attr_slice() (nee
heap_tuple_untoast_attr_slice()), since it's far from clear that
no other code paths leading to that function could pass it values
that would overflow.
Patch by myself and Pavel Stehule, per bug #16804 from Rafi Shamim.
Back-patch to v11. While these bugs are old, the common/int.h
infrastructure for overflow-detecting arithmetic didn't exist before
commit 4d6ad3125, and it doesn't seem like these misbehaviors are bad
enough to justify developing a standalone fix for the older branches.
Discussion: https://postgr.es/m/16804-f4eeeb6c11ba71d4@postgresql.org
In the wake of the previous commit, we don't really need this anymore,
since array assignment is primarily handled by the core code.
The only way that that code could still be reached is that a GET
DIAGNOSTICS target variable could be an array element. But that
doesn't seem like a particularly essential feature. I'd added it
in commit 55caaaeba, but just because it was easy not because
anyone had actually asked for it. Hence, revert that patch and
then remove the now-unreachable stuff. (If we really had to,
we could probably reimplement GET DIAGNOSTICS using the new
assignment machinery; but the cost/benefit ratio looks very poor,
and it'd likely be a bit slower.)
Note that PLPGSQL_DTYPE_RECFIELD remains. It's possible that we
could get rid of that too, but maintaining the existing behaviors
for RECORD-type variables seems like it might be difficult. Since
there's not any functional limitation in those code paths as there
was in the ARRAYELEM code, I've not pursued the idea.
Discussion: https://postgr.es/m/4165684.1607707277@sss.pgh.pa.us
Invent new RawParseModes that allow the core grammar to handle
pl/pgsql expressions and assignments directly, and thereby get rid
of a lot of hackery in pl/pgsql's parser. This moves a good deal
of knowledge about pl/pgsql into the core code: notably, we have to
invent a CoercionContext that matches pl/pgsql's (rather dubious)
historical behavior for assignment coercions. That's getting away
from the original idea of pl/pgsql as an arm's-length extension of
the core, but really we crossed that bridge a long time ago.
The main advantage of doing this is that we can now use the core
parser to generate FieldStore and/or SubscriptingRef nodes to handle
assignments to pl/pgsql variables that are records or arrays. That
fixes a number of cases that had never been implemented in pl/pgsql
assignment, such as nested records and array slicing, and it allows
pl/pgsql assignment to support the datatype-specific subscripting
behaviors introduced in commit c7aba7c14.
There are cosmetic benefits too: when a syntax error occurs in a
pl/pgsql expression, the error report no longer includes the confusing
"SELECT" keyword that used to get prefixed to the expression text.
Also, there seem to be some small speed gains.
Discussion: https://postgr.es/m/4165684.1607707277@sss.pgh.pa.us
Since at least 2001 we've used putenv() and avoided setenv(), on the
grounds that the latter was unportable and not in POSIX. However,
POSIX added it that same year, and by now the situation has reversed:
setenv() is probably more portable than putenv(), since POSIX now
treats the latter as not being a core function. And setenv() has
cleaner semantics too. So, let's reverse that old policy.
This commit adds a simple src/port/ implementation of setenv() for
any stragglers (we have one in the buildfarm, but I'd not be surprised
if that code is never used in the field). More importantly, extend
win32env.c to also support setenv(). Then, replace usages of putenv()
with setenv(), and get rid of some ad-hoc implementations of setenv()
wannabees.
Also, adjust our src/port/ implementation of unsetenv() to follow the
POSIX spec that it returns an error indicator, rather than returning
void as per the ancient BSD convention. I don't feel a need to make
all the call sites check for errors, but the portability stub ought
to match real-world practice.
Discussion: https://postgr.es/m/2065122.1609212051@sss.pgh.pa.us
Attempt to get selectivity estimation for @> (anymultirange, anyrange) operator
caused an error in buildfarm, because this operator was missed in switch()
of calc_hist_selectivity(). Fix that and also make regression tests reliably
check that selectivity estimation for (multi)ranges doesn't fall. Previously,
whether we test selectivity estimation for (multi)ranges depended on
whether autovacuum managed to gather concurrently to the test.
Reported-by: Michael Paquier
Discussion: https://postgr.es/m/X%2BwmgjRItuvHNBeV%40paquier.xyz
IF NOT EXISTS was ignored when specified in an EXPLAIN query for CREATE
MATERIALIZED VIEW or CREATE TABLE AS. Hence, if this clause was
specified, the caller would get a failure if the relation already
exists instead of a success with a NOTICE message.
This commit makes the behavior of IF NOT EXISTS in EXPLAIN consistent
with the non-EXPLAIN'd DDL queries, preventing a failure with IF NOT
EXISTS if the relation to-be-created already exists. The skip is done
before the SELECT query used for the relation is planned or executed,
and a "dummy" plan is generated instead depending on the format used by
EXPLAIN.
Author: Bharath Rupireddy
Reviewed-by: Zhijie Hou, Michael Paquier
Discussion: https://postgr.es/m/CALj2ACVa3oJ9O_wcGd+FtHWZds04dEKcakxphGz5POVgD4wC7Q@mail.gmail.com
6df7a9698b has introduced a set of operators between ranges and multiranges.
Existing GiST indexes for ranges could easily support majority of them.
This commit adds support for new operators to the existing range GiST indexes.
New operators resides the same strategy numbers as existing ones. Appropriate
check function is determined using the subtype.
Catversion is bumped.
We have operators for checking if the multirange contains a range but don't
have the opposite. This commit improves completeness of the operator set by
adding two new operators: @> (anyrange,anymultirange) and
<@(anymultirange,anyrange).
Catversion is bumped.
Two functions multirange_range_overlaps_bsearch_comparison() and
multirange_range_contains_bsearch_comparison() contain bugs of returning -1
instead of 1. This commit fixes these bugs and adds corresponding regression
tests.
Removing the EXPLAIN test to stabilize the buildfarm. The execution
test should still be effective to catch the bug even if the plan is
slightly different on different platforms.
Before processing tuples, agg_refill_hash_table() was setting all
pergroup pointers to NULL to signal to advance_aggregates() that it
should not attempt to advance groups that had spilled.
The problem was that it also set the pergroups for sorted grouping
sets to NULL, which caused rescanning to fail.
Instead, change agg_refill_hash_table() to only set the pergroups for
hashed grouping sets to NULL; and when compiling the expression, pass
doSort=false.
Reported-by: Alexander Lakhin
Discussion: https://postgr.es/m/16784-7ff169bf2c3d1588%40postgresql.org
Backpatch-through: 13
This makes existing sessions reflect "ALTER ROLE ... [NO]INHERIT" as
quickly as they have been reflecting "GRANT role_name". Back-patch to
9.5 (all supported versions).
Reviewed by Nathan Bossart.
Discussion: https://postgr.es/m/20201221095028.GB3777719@rfd.leadboat.com
This adds a key management system that stores (currently) two data
encryption keys of length 128, 192, or 256 bits. The data keys are
AES256 encrypted using a key encryption key, and validated via GCM
cipher mode. A command to obtain the key encryption key must be
specified at initdb time, and will be run at every database server
start. New parameters allow a file descriptor open to the terminal to
be passed. pg_upgrade support has also been added.
Discussion: https://postgr.es/m/CA+fd4k7q5o6Nc_AaX6BcYM9yqTbC6_pnH-6nSD=54Zp6NBQTCQ@mail.gmail.com
Discussion: https://postgr.es/m/20201202213814.GG20285@momjian.us
Author: Masahiko Sawada, me, Stephen Frost
Buildfarm members pogona and petalura have shown a failure when
pg_ctl/t/004_logrotate.pl starts just before local midnight.
The default rotate-at-midnight behavior occurs just before the
Perl script examines current_logfiles, so it figures that the
rotation it's already requested has occurred ... but in reality,
that rotation happens just after it looks, so the expected new
log data goes into a different file than the one it's examining.
In HEAD, src/test/kerberos/t/001_auth.pl has acquired similar code
that evidently has a related failure mode. Besides being quite new,
few buildfarm critters run that test, so it's unsurprising that
we've not yet seen a failure there.
Fix both cases by setting log_rotation_age = 0 so that no time-based
rotation can occur. Also absorb 004_logrotate.pl's decision to
set lc_messages = 'C' into the kerberos test, in hopes that it will
work in non-English prevailing locales.
Report: https://buildfarm.postgresql.org/cgi-bin/show_log.pl?nm=pogona&dt=2020-12-24%2022%3A10%3A04
Report: https://buildfarm.postgresql.org/cgi-bin/show_log.pl?nm=petalura&dt=2020-02-01%2022%3A20%3A04
The parsing of this parameter has been using strtoul(), which is not
portable across platforms. On most Unix platforms, unsigned long has a
size of 64 bits, while on Windows it is 32 bits. It is common in
recovery scenarios to rely on the output of txid_current() or even the
newer pg_current_xact_id() to get a transaction ID for setting up
recovery_target_xid. The value returned by those functions includes the
epoch in the computed result, which would cause strtoul() to fail where
unsigned long has a size of 32 bits once the epoch is incremented.
WAL records and 2PC data include only information about 32-bit XIDs and
it is not possible to have XIDs across more than one epoch, so
discarding the high bits from the transaction ID set has no impact on
recovery. On the contrary, the use of strtoul() prevents a consistent
behavior across platforms depending on the size of unsigned long.
This commit changes the parsing of recovery_target_xid to use
pg_strtouint64() instead, available down to 9.6. There is one TAP test
stressing recovery with recovery_target_xid, where a tweak based on
pg_reset{xlog,wal} is added to bump the XID epoch so as this change gets
tested, as per an idea from Alexander Lakhin.
Reported-by: Alexander Lakhin
Discussion: https://postgr.es/m/16780-107fd0c0385b1035@postgresql.org
Backpatch-through: 9.6
While we do allow SRFs in ORDER BY, scan/join processing should not
consider such cases - such sorts should only happen via final Sort atop
a ProjectSet. So make sure we don't try adding such sorts below Gather
Merge, just like we do for expressions that are volatile and/or not
parallel safe.
Backpatch to PostgreSQL 13, where this code was introduced as part of
the Incremental Sort patch.
Author: James Coleman
Reviewed-by: Tomas Vondra
Backpatch-through: 13
Discussion: https://postgr.es/m/CAAaqYe8cK3g5CfLC4w7bs=hC0mSksZC=H5M8LSchj5e5OxpTAg@mail.gmail.com
Discussion: https://postgr.es/m/295524.1606246314%40sss.pgh.pa.us
The jsonb || jsonb operator arbitrarily rejected certain combinations
of scalar and non-scalar inputs, while being willing to concatenate
other combinations. This was of course quite undocumented. Rather
than trying to document it, let's just remove the restriction,
creating a uniform rule that unless we are handling an object-to-object
concatenation, non-array inputs are converted to one-element arrays,
resulting in an array-to-array concatenation. (This does not change
the behavior for any case that didn't throw an error before.)
Per complaint from Joel Jacobson. Back-patch to all supported branches.
Discussion: https://postgr.es/m/163099.1608312033@sss.pgh.pa.us
Commit ebb7ae839d ensured we ignore pathkeys with volatile expressions
when considering adding a sort below a Gather Merge. Turns out we need
to care about parallel safety of the pathkeys too, otherwise we might
try sorting e.g. on results of a correlated subquery (as demonstrated
by a report from Luis Roberto).
Initial investigation by Tom Lane, patch by James Coleman. Backpatch
to 13, where the code was instroduced (as part of Incremental Sort).
Reported-by: Luis Roberto
Author: James Coleman
Reviewed-by: Tomas Vondra
Backpatch-through: 13
Discussion: https://postgr.es/m/622580997.37108180.1604080457319.JavaMail.zimbra%40siscobra.com.br
Discussion: https://postgr.es/m/CAAaqYe8cK3g5CfLC4w7bs=hC0mSksZC=H5M8LSchj5e5OxpTAg@mail.gmail.com
generate_useful_gather_paths used to skip unsorted paths (without any
pathkeys), but that is unnecessary - the later code actually can handle
such paths just fine by adding a Sort node. This is clearly a thinko,
preventing construction of useful plans.
Backpatch to 13, where Incremental Sort was introduced.
Author: James Coleman
Reviewed-by: Tomas Vondra
Backpatch-through: 13
Discussion: https://postgr.es/m/CAAaqYe8cK3g5CfLC4w7bs=hC0mSksZC=H5M8LSchj5e5OxpTAg@mail.gmail.com
Multiranges are basically sorted arrays of non-overlapping ranges with
set-theoretic operations defined over them.
Since v14, each range type automatically gets a corresponding multirange
datatype. There are both manual and automatic mechanisms for naming multirange
types. Once can specify multirange type name using multirange_type_name
attribute in CREATE TYPE. Otherwise, a multirange type name is generated
automatically. If the range type name contains "range" then we change that to
"multirange". Otherwise, we add "_multirange" to the end.
Implementation of multiranges comes with a space-efficient internal
representation format, which evades extra paddings and duplicated storage of
oids. Altogether this format allows fetching a particular range by its index
in O(n).
Statistic gathering and selectivity estimation are implemented for multiranges.
For this purpose, stored multirange is approximated as union range without gaps.
This field will likely need improvements in the future.
Catversion is bumped.
Discussion: https://postgr.es/m/CALNJ-vSUpQ_Y%3DjXvTxt1VYFztaBSsWVXeF1y6gTYQ4bOiWDLgQ%40mail.gmail.com
Discussion: https://postgr.es/m/a0b8026459d1e6167933be2104a6174e7d40d0ab.camel%40j-davis.com#fe7218c83b08068bfffb0c5293eceda0
Author: Paul Jungwirth, revised by me
Reviewed-by: David Fetter, Corey Huinker, Jeff Davis, Pavel Stehule
Reviewed-by: Alvaro Herrera, Tom Lane, Isaac Morland, David G. Johnston
Reviewed-by: Zhihong Yu, Alexander Korotkov
Commit 257836a75 added the "locale" subdirectory to SUBDIRS,
but neglected to remove it from ALWAYS_SUBDIRS. This oversight
had no functional effect because the filter-out function would
remove it anyway. Still, it's confusing to readers to list a
subdirectory in both places, especially because it makes the
associated comment into a partial lie.
Any subdirectory that's ignoring /output_iso/ should also
ignore /tmp_check_iso/, which could be left behind by a
failed pg_isolation_regress_check run.
I think these have been wrong for awhile, but it doesn't
seem important to fix in back branches.
Many older tests where written in a style like
SELECT '' AS two, i.* FROM INT2_TBL
where the first column indicated the number of expected result rows.
This has gotten increasingly out of date, as the test data fixtures
have expanded, so a lot of these were wrong and misleading. Moreover,
this style isn't really necessary, since the psql output already shows
the number of result rows.
To clean this up, remove all those extra columns.
Discussion: https://www.postgresql.org/message-id/flat/1a25312b-2686-380d-3c67-7a69094a999f%40enterprisedb.com
This is essential if we'd like to allow existing extension data types
to support subscripting in future, since dropping and recreating the
type isn't a practical thing for an extension upgrade script, and
direct manipulation of pg_type isn't a great answer either.
There was some discussion about also allowing alteration of typelem,
but it's less clear whether that's a good idea or not, so for now
I forebore.
Discussion: https://postgr.es/m/3724341.1607551174@sss.pgh.pa.us
Commit c7aba7c14 didn't add this, but after more fooling with the
feature I feel that it'd be useful. To make this possible, refactor
getSubscriptingRoutines() so that the caller is responsible for
throwing any error. (In clauses.c, I just chose to make the
most conservative assumption rather than throwing an error. We don't
expect failures there anyway really, so the code space for an error
message would be a poor investment.)
This patch generalizes the subscripting infrastructure so that any
data type can be subscripted, if it provides a handler function to
define what that means. Traditional variable-length (varlena) arrays
all use array_subscript_handler(), while the existing fixed-length
types that support subscripting use raw_array_subscript_handler().
It's expected that other types that want to use subscripting notation
will define their own handlers. (This patch provides no such new
features, though; it only lays the foundation for them.)
To do this, move the parser's semantic processing of subscripts
(including coercion to whatever data type is required) into a
method callback supplied by the handler. On the execution side,
replace the ExecEvalSubscriptingRef* layer of functions with direct
calls to callback-supplied execution routines. (Thus, essentially
no new run-time overhead should be caused by this patch. Indeed,
there is room to remove some overhead by supplying specialized
execution routines. This patch does a little bit in that line,
but more could be done.)
Additional work is required here and there to remove formerly
hard-wired assumptions about the result type, collation, etc
of a SubscriptingRef expression node; and to remove assumptions
that the subscript values must be integers.
One useful side-effect of this is that we now have a less squishy
mechanism for identifying whether a data type is a "true" array:
instead of wiring in weird rules about typlen, we can look to see
if pg_type.typsubscript == F_ARRAY_SUBSCRIPT_HANDLER. For this
to be bulletproof, we have to forbid user-defined types from using
that handler directly; but there seems no good reason for them to
do so.
This patch also removes assumptions that the number of subscripts
is limited to MAXDIM (6), or indeed has any hard-wired limit.
That limit still applies to types handled by array_subscript_handler
or raw_array_subscript_handler, but to discourage other dependencies
on this constant, I've moved it from c.h to utils/array.h.
Dmitry Dolgov, reviewed at various times by Tom Lane, Arthur Zakirov,
Peter Eisentraut, Pavel Stehule
Discussion: https://postgr.es/m/CA+q6zcVDuGBv=M0FqBYX8DPebS3F_0KQ6OVFobGJPM507_SZ_w@mail.gmail.com
Discussion: https://postgr.es/m/CA+q6zcVovR+XY4mfk-7oNk-rF91gH0PebnNfuUjuuDsyHjOcVA@mail.gmail.com
Formerly, extended statistics only handled clauses that were
RestrictInfos. However, the restrictinfo machinery doesn't create
sub-AND RestrictInfos for AND clauses underneath OR clauses.
Therefore teach extended statistics to handle bare AND clauses,
looking for compatible RestrictInfo clauses underneath them.
Dean Rasheed, reviewed by Tomas Vondra.
Discussion: https://postgr.es/m/CAEZATCW=J65GUFm50RcPv-iASnS2mTXQbr=CfBvWRVhFLJ_fWA@mail.gmail.com
When estimating an OR clause using multiple extended statistics
objects, treat the estimates for each set of clauses for each
statistics object as independent of one another. The overlap estimates
produced for each statistics object do not apply to clauses covered by
other statistics objects.
Dean Rasheed, reviewed by Tomas Vondra.
Discussion: https://postgr.es/m/CAEZATCW=J65GUFm50RcPv-iASnS2mTXQbr=CfBvWRVhFLJ_fWA@mail.gmail.com
Exercise some error cases that were never reached in the existing
regression tests. This is partly for code-coverage reasons, and
partly to memorialize the current behavior in advance of planned
changes for generic subscripting.
Also, I noticed that type_sanity's check to verify that all standard
types have array types was never extended when we added arrays for
all system catalog rowtypes (f7f70d5e2), nor when we added arrays
over domain types (c12d570fa). So do that. Also, since the query's
expected output isn't empty, it seems like a good idea to add an
ORDER BY to make sure the result stays stable.
Commit 4be058fe9 forgot that the append_rel_list would already be
populated at the time we remove useless result RTEs, and it might contain
PlaceHolderVars that need to be adjusted like the ones in the main parse
tree. This could lead to "no relation entry for relid N" failures later
on, when the planner tries to do something with an unadjusted PHV.
Per report from Tom Ellis. Back-patch to v12 where the bug came in.
Discussion: https://postgr.es/m/20201205173056.GF30712@cloudinit-builder
Formerly we only applied extended statistics to an OR clause as part
of the clauselist_selectivity() code path for an OR clause appearing
in an implicitly-ANDed list of clauses. This meant that it could only
use extended statistics if all sub-clauses of the OR clause were
covered by a single extended statistics object.
Instead, teach clause_selectivity() how to apply extended statistics
to an OR clause by handling its ORed list of sub-clauses in a similar
manner to an implicitly-ANDed list of sub-clauses, but with different
combination rules. This allows one or more extended statistics objects
to be used to estimate all or part of the list of sub-clauses. Any
remaining sub-clauses are then treated as if they are independent.
Additionally, to avoid double-application of extended statistics, this
introduces "extended" versions of clause_selectivity() and
clauselist_selectivity(), which include an option to ignore extended
statistics. This replaces the old clauselist_selectivity_simple()
function which failed to completely ignore extended statistics when
called from the extended statistics code.
A known limitation of the current infrastructure is that an AND clause
under an OR clause is not treated as compatible with extended
statistics (because we don't build RestrictInfos for such sub-AND
clauses). Thus, for example, "(a=1 AND b=1) OR (a=2 AND b=2)" will
currently be treated as two independent AND clauses (each of which may
be estimated using extended statistics), but extended statistics will
not currently be used to account for any possible overlap between
those clauses. Improving that is left as a task for the future.
Original patch by Tomas Vondra, with additional improvements by me.
Discussion: https://postgr.es/m/20200113230008.g67iyk4cs3xbnjju@development
This changes CLUSTER and REINDEX so as a parenthesized grammar becomes
possible for options, while unifying the grammar parsing rules for
option lists with the existing ones.
This is a follow-up of the work done in 873ea9e for VACUUM, ANALYZE and
EXPLAIN. This benefits REINDEX for a potential backend-side filtering
for collatable-sensitive indexes and TABLESPACE, while CLUSTER would
benefit from the latter.
Author: Alexey Kondratov, Justin Pryzby
Discussion: https://postgr.es/m/8a8f5f73-00d3-55f8-7583-1375ca8f6a91@postgrespro.ru
GSS information (if used) such as if the connection was authorized using
GSS or if it was encrypted using GSS, and perhaps most importantly, what
the GSS principal used for the authentication was, is extremely useful
but wasn't being included in the connection authorized log message.
Therefore, add to the connection authorized log message that
information, in a similar manner to how we log SSL information when SSL
is used for a connection.
Author: Vignesh C
Reviewed-by: Bharath Rupireddy
Discussion: https://www.postgresql.org/message-id/CALDaNm2N1385_Ltoo%3DS7VGT-ESu_bRQa-sC1wg6ikrM2L2Z49w%40mail.gmail.com
Commit 6b466bf5f2 allowed pg_stat_statements to track the number of
WAL records, full page images and bytes that each statement generated.
Similarly this commit allows us to track the cluster-wide WAL statistics
counters.
New columns wal_records, wal_fpi and wal_bytes are added into the
pg_stat_wal view, and reports the total number of WAL records,
full page images and bytes generated in the , respectively.
Author: Masahiro Ikeda
Reviewed-by: Amit Kapila, Movead Li, Kyotaro Horiguchi, Fujii Masao
Discussion: https://postgr.es/m/35ef960128b90bfae3b3fdf60a3a860f@oss.nttdata.com
As it stood, expandTableLikeClause() re-did the same relation_openrv
call that transformTableLikeClause() had done. However there are
scenarios where this would not find the same table as expected.
We hold lock on the LIKE source table, so it can't be renamed or
dropped, but another table could appear before it in the search path.
This explains the odd behavior reported in bug #16758 when cloning a
table as a temp table of the same name. This case worked as expected
before commit 502898192 introduced the need to open the source table
twice, so we should fix it.
To make really sure we get the same table, let's re-open it by OID not
name. That requires adding an OID field to struct TableLikeClause,
which is a little nervous-making from an ABI standpoint, but as long
as it's at the end I don't think there's any serious risk.
Per bug #16758 from Marc Boeren. Like the previous patch,
back-patch to all supported branches.
Discussion: https://postgr.es/m/16758-840e84a6cfab276d@postgresql.org
If a PlaceHolderVar is to be evaluated at a join relation, but
its value is only needed there and not at higher levels, we neglected
to update the joinrel's direct_lateral_relids to include the PHV's
source rel. This causes problems because join_is_legal() then won't
allow joining the joinrel to the PHV's source rel at all, leading
to "failed to build any N-way joins" planner failures.
Per report from Andreas Seltenreich. Back-patch to 9.5
where the problem originated.
Discussion: https://postgr.es/m/87blfgqa4t.fsf@aurora.ydns.eu
Previously test_shm_mq worker used the stripped-down version of die()
as the SIGTERM signal handler. This commit makes it use die(), instead,
to simplify the code.
In terms of the code, the difference between die() and the stripped-down
version previously used is whether the signal handler directly may call
ProcessInterrupts() or not. But this difference doesn't exist in
a background worker because, in bgworker, DoingCommandRead flag will
never be true and die() will never call ProcessInterrupts() directly.
Therefore test_shm_mq worker can safely use die(), like other bgworker
proceses (e.g., logical replication apply launcher or autoprewarm worker)
currently do.
Thanks to Craig Ringer for the report and investigation of the issue.
Author: Bharath Rupireddy
Reviewed-by: Fujii Masao
Discussion: https://postgr.es/m/CAGRY4nxsAe_1k_9g5b47orA0S011iBoHsXHFMH7cg7HV0O1bwQ@mail.gmail.com
Previously worker_spi used its custom signal handlers for SIGHUP and
SIGTERM. This commit makes worker_spi use the standard signal handlers,
to simplify the code.
Note that die() is used as the standard SIGTERM signal handler in
worker_spi instead of SignalHandlerForShutdownRequest() or bgworker_die().
Previously the exit handling was only able to exit from within the main loop,
and not from within the backend code it calls. This is why die() needs to
be used here, so worker_spi can respond to SIGTERM signal while it's
executing a query.
Maybe we can say that it's a bug that worker_spi could not respond to
SIGTERM during query execution. But since worker_spi is a just example
of the background worker code, we don't do the back-patch.
Thanks to Craig Ringer for the report and investigation of the issue.
Author: Bharath Rupireddy
Reviewed-by: Fujii Masao
Discussion: https://postgr.es/m/CALj2ACXDEZhAFOTDcqO9cFSRvrFLyYOnPKrcA1UG4uZn9hUAVg@mail.gmail.com
Discussion: https://postgr.es/m/CAGRY4nxsAe_1k_9g5b47orA0S011iBoHsXHFMH7cg7HV0O1bwQ@mail.gmail.com
currtid() and currtid2() are an undocumented set of functions whose sole
known user is the Postgres ODBC driver, able to retrieve the latest TID
version for a tuple given by the caller of those functions.
As used by Postgres ODBC, currtid() is a shortcut able to retrieve the
last TID loaded into a backend by passing an OID of 0 (magic value)
after a tuple insertion. This is removed in this commit, as it became
obsolete after the driver began using "RETURNING ctid" with inserts, a
clause supported since Postgres 8.2 (using RETURNING is better for
performance anyway as it reduces the number of round-trips to the
backend).
currtid2() is still used by the driver, so this remains around for now.
Note that this function is kept in its original shape for backward
compatibility reasons.
Per discussion with many people, including Andres Freund, Peter
Eisentraut, Álvaro Herrera, Hiroshi Inoue, Tom Lane and myself.
Bump catalog version.
Discussion: https://postgr.es/m/20200603021448.GB89559@paquier.xyz
Historically these were called >^ and <^, but that is inconsistent
with the similar box, polygon, and circle operators, which are named
|>> and <<| respectively. Worse, the >^ and <^ names are used for
*not* strict above/below tests for the box type.
Hence, invent new operators following the more common naming. The
old operators remain available for now, and are still accepted by
the relevant index opclasses too. But there's a deprecation notice,
so maybe we can get rid of them someday.
Emre Hasegeli, reviewed by Pavel Borisov
Discussion: https://postgr.es/m/24348.1587444160@sss.pgh.pa.us
Tom Lane
Amit Kapila
David Rowley
Daniel Gustafsson
Dean Rasheed
Peter Eisentraut
Andrew Dunstan
Alvaro Herrera
John Naylor
Michael Paquier
Fujii Masao
Tomas Vondra
Alexander Korotkov
Noah Misch
Peter Geoghegan
Robert Haas
Thomas Munro
Bruce Momjian
Andres Freund
Heikki Linnakangas
Stephen Frost
Joe Conway
Etsuro Fujita
Magnus Hagander
Jeff Davis