pg_verifybackup needs by default pg_waldump to check after a range of
WAL segments required for a backup, except if --no-parse-wal is
specified. The code checked for the presence of the binary pg_waldump
in an installation and reported an error, but it forgot to properly
exit(). This could lead to confusing errors reported.
Reviewed-by: Robert Haas, Fabien Coelho
Discussion: https://postgr.es/m/YQDMdB+B68yePFeT@paquier.xyz
Backpatch-through: 13
If a file is truncated, we must update minRecoveryPoint. Once a file is
truncated, there's no going back; it would not be safe to stop recovery
at a point earlier than that anymore.
Commit 7bffc9b7bf changed xact_redo_commit() so that it updates
minRecoveryPoint on truncation, but forgot to change xact_redo_abort().
Back-patch to all supported versions.
Reported-by: mengjuan.cmj@alibaba-inc.com
Author: Fujii Masao
Reviewed-by: Heikki Linnakangas
Discussion: https://postgr.es/m/b029fce3-4fac-4265-968e-16f36ff4d075.mengjuan.cmj@alibaba-inc.com
It wasn't all that clear which lock levels, if any, would be held on the
DEFAULT partition during an ATTACH PARTITION operation.
Also, clarify which locks will be taken if the DEFAULT partition or the
table being attached are themselves partitioned tables.
Here I'm only backpatching to v12 as before then we obtained an ACCESS
EXCLUSIVE lock on the partitioned table. It seems much less relevant to
mention which locks are taken on other tables when the partitioned table
itself is locked with an ACCESS EXCLUSIVE lock.
Author: Matthias van de Meent, David Rowley
Discussion: https://postgr.es/m/CAEze2WiTB6iwrV8W_J=fnrnZ7fowW3qu-8iQ8zCHP3FiQ6+o-A@mail.gmail.com
Backpatch-through: 12
This changes the behavior of examining the pg_file_settings view after
changing a config option that requires restart. The user needs to know
that any change of such options does not take effect until a restart,
and this worked correctly if the line is edited without removing it.
However, for the case where the line is removed altogether, the flag
doesn't get set, because a flag was only set in set_config_option, but
that's not called for lines removed. Repair.
(Ref.: commits 62d16c7fc5 and a486e35706)
Author: Álvaro Herrera <alvherre@alvh.no-ip.org>
Reviewed-by: Daniel Gustafsson <daniel@yesql.se>
Reviewed-by: Tom Lane <tgl@sss.pgh.pa.us>
Discussion: https://postgr.es/m/202107262302.xsfdfc5sb7sh@alvherre.pgsql
The error messages using the word "non-negative" are confusing
because it's ambiguous about whether it accepts zero or not.
This commit improves those error messages by replacing it with
less ambiguous word like "greater than zero" or
"greater than or equal to zero".
Also this commit added the note about the word "non-negative" to
the error message style guide, to help writing the new error messages.
When postgres_fdw option fetch_size was set to zero, previously
the error message "fetch_size requires a non-negative integer value"
was reported. This error message was outright buggy. Therefore
back-patch to all supported versions where such buggy error message
could be thrown.
Reported-by: Hou Zhijie
Author: Bharath Rupireddy
Reviewed-by: Kyotaro Horiguchi, Fujii Masao
Discussion: https://postgr.es/m/OS0PR01MB5716415335A06B489F1B3A8194569@OS0PR01MB5716.jpnprd01.prod.outlook.com
Add pg_resetxlog -u option to set the oldest xid in pg_control.
Previously -x set this value be -2 billion less than the -x value.
However, this causes the server to immediately scan all relation's
relfrozenxid so it can advance pg_control's oldest xid to be inside the
autovacuum_freeze_max_age range, which is inefficient and might disrupt
diagnostic recovery. pg_upgrade will use this option to better create
the new cluster to match the old cluster.
Reported-by: Jason Harvey, Floris Van Nee
Discussion: https://postgr.es/m/20190615183759.GB239428@rfd.leadboat.com, 87da83168c644fd9aae38f546cc70295@opammb0562.comp.optiver.com
Author: Bertrand Drouvot
Backpatch-through: 9.6
These have been introduced by 7fbe0c8, and could happen for
pg_basebackup and pg_receivewal.
Per report from Coverity for the ones in walmethods.c, I have spotted
the ones in receivelog.c after more review.
Backpatch-through: 10
The point of introducing the hash_mem_multiplier GUC was to let users
reproduce the old behavior of hash aggregation, i.e. that it could use
more than work_mem at need. However, the implementation failed to get
the job done on Win64, where work_mem is clamped to 2GB to protect
various places that calculate memory sizes using "long int". As
written, the same clamp was applied to hash_mem. This resulted in
severe performance regressions for queries requiring a bit more than
2GB for hash aggregation, as they now spill to disk and there's no
way to stop that.
Getting rid of the work_mem restriction seems like a good idea, but
it's a big job and could not conceivably be back-patched. However,
there's only a fairly small number of places that are concerned with
the hash_mem value, and it turns out to be possible to remove the
restriction there without too much code churn or any ABI breaks.
So, let's do that for now to fix the regression, and leave the
larger task for another day.
This patch does introduce a bit more infrastructure that should help
with the larger task, namely pg_bitutils.h support for working with
size_t values.
Per gripe from Laurent Hasson. Back-patch to v13 where the
behavior change came in.
Discussion: https://postgr.es/m/997817.1627074924@sss.pgh.pa.us
Discussion: https://postgr.es/m/MN2PR15MB25601E80A9B6D1BA6F592B1985E39@MN2PR15MB2560.namprd15.prod.outlook.com
This commit changes the startup process in the standby server so that
it handles the interrupt signals after waiting for wal_retrieve_retry_interval
on the latch and resetting it, before entering another wait on the latch.
This change causes the standby server to promptly handle interrupt signals.
Otherwise, previously, there was the case where the standby needs to
wait extra five seconds to shutdown when the shutdown request arrived
while the startup process was waiting for wal_retrieve_retry_interval
on the latch.
Author: Fujii Masao, but implementation idea is from Soumyadeep Chakraborty
Reviewed-by: Soumyadeep Chakraborty
Discussion: https://postgr.es/m/9d7e6ab0-8a53-ddb9-63cd-289bcb25fe0e@oss.nttdata.com
Per discussion of BUG #17073, back-patch to all supported versions.
Discussion: https://postgr.es/m/17073-1a5fdaed0fa5d4d0@postgresql.org
We have an implementation restriction that PREPARE TRANSACTION can't
handle cases where both session-lifespan and transaction-lifespan locks
are held on the same lockable object. (That's because we'd otherwise
need to acquire a new PROCLOCK entry during post-prepare cleanup, which
is an operation that might fail. The situation can only arise with odd
usages of advisory locks, so removing the restriction is probably not
worth the amount of effort it would take.) AtPrepare_Locks attempted
to enforce this, but its logic was many bricks shy of a load, because
it only detected cases where the session and transaction locks had the
same lockmode. Locks of different modes on the same object would lead
to the rather unhelpful message "PANIC: we seem to have dropped a bit
somewhere".
To fix, build a transient hashtable with one entry per locktag,
not one per locktag + mode, and use that to detect conflicts.
Per bug #17122 from Alexander Pyhalov. This bug is ancient,
so back-patch to all supported branches.
Discussion: https://postgr.es/m/17122-04f3c32098a62233@postgresql.org
We previously took a hard-line attitude that callers should never print
a null string pointer, and doing so is worthy of an assertion failure
or crash. However, we've long since flushed out any easy-to-find bugs
of that nature. What remains is a lot of code that perhaps could fail
that way in hard-to-reach corner cases. For example, in something as
simple as
ereport(ERROR,
(errcode(ERRCODE_UNDEFINED_OBJECT),
errmsg("constraint \"%s\" for table \"%s\" does not exist",
conname, get_rel_name(relid))));
one must wonder whether it's completely guaranteed that get_rel_name
cannot return NULL in this context. If such a situation did occur,
the existing policy converts what might be a pretty minor bug into
a server crash condition. This is not good for robustness.
Hence, let's follow the lead of glibc and print "(null)" instead
of failing. We should, of course, still consider it a bug if that
behavior is reachable in ordinary use; but crashing seems less
desirable than not crashing.
This fix works across-the-board in v12 and up, where we always use
src/port/snprintf.c. Before that, on most platforms we're at the mercy
of the local libc, but it appears that Solaris 10 is the only supported
platform where we'd still get a crash. Most other platforms such as
*BSD, macOS, and Solaris 11 have adopted glibc's behavior at some
point. (AIX and HPUX just print "" not "(null)", but that's close
enough.) I've not checked what Windows' native printf would do, but
it doesn't matter because we've long used snprintf.c on that platform.
In v12 and up, also const-ify related code so that we're not casting
away const on the constant string. This is just neatnik-ism, since
next to no compilers will warn about that.
Discussion: https://postgr.es/m/17098-b960f3616c861f83@postgresql.org
Code inlined by LLVM can crash or fail with "Relocation type not
implemented yet!" if it tries to access thread local variables. Don't
inline such code.
Back-patch to 11, where LLVM arrived. Bug #16696.
Author: Dmitry Marakasov <amdmi3@amdmi3.ru>
Reviewed-by: Andres Freund <andres@anarazel.de>
Discussion: https://postgr.es/m/16696-29d944a33801fbfe@postgresql.org
In postgresql.conf, memory and file size GUCs can be specified with "B"
(bytes) as of b06d8e58b. Likewise, time GUCs can be specified with "us"
(microseconds) as of caf626b2c. Update postgres.conf.sample to reflect
that fact.
Pavel Luzanov
Backpatch to v12, which is the earliest version that allows both of
these units. A separate commit will document the "B" case for v11.
Discussion: https://www.postgresql.org/message-id/flat/f10d16fc-8fa0-1b3c-7371-cb3a35a13b7a%40postgrespro.ru
If an error was raised during our initial attempt to check whether
a successfully-compiled expression is "simple", subsequent calls of
exec_stmt_execsql would suppose that stmt->mod_stmt was already computed
when it had not been. This could lead to assertion failures in debug
builds; in production builds the effect would typically be to act as
if INTO STRICT had been specified even when it had not been. Of course
that only matters if the subsequent attempt to execute the expression
succeeds, so that the problem can only be reached by fixing a failure
in some referenced, inline-able SQL function and then retrying the
calling plpgsql function in the same session.
(There might be even-more-obscure ways to change the expression's
behavior without changing the plpgsql function, but that one seems
like the only one people would be likely to hit in practice.)
The most foolproof way to fix this would be to arrange for
exec_prepare_plan to not set expr->plan until we've finished the
subsidiary simple-expression check. But it seems hard to do that
without creating reference-count leak issues. So settle for documenting
the hazard in a comment and fixing exec_stmt_execsql to test separately
for whether it's computed stmt->mod_stmt. (That adds a test-and-branch
per execution, but hopefully that's negligible in context.) In v11 and
up, also fix exec_stmt_call which had a variant of the same issue.
Per bug #17113 from Alexander Lakhin. Back-patch to all
supported branches.
Discussion: https://postgr.es/m/17113-077605ce00e0e7ec@postgresql.org
The logic handling the opening of new WAL segments was fuzzy when using
--compress if a partial, non-compressed, segment with the same base name
existed in the repository storing those files. In this case, using
--compress would cause the code to first check for the existence and the
size of a non-compressed segment, followed by the opening of a new
compressed, partial, segment. The code was accidentally working
correctly on most platforms as the buildfarm has proved, except
bowerbird where gzflush() could fail in this code path. It is wrong
anyway to take the code path used pre-padding when creating a new
partial, non-compressed, segment, so let's fix it.
Note that this issue exists when users mix successive runs of
pg_receivewal with or without compression, as discovered with the tests
introduced by ffc9dda.
While on it, this refactors the code so as code paths that need to know
about the ".gz" suffix are down from four to one in walmethods.c, easing
a bit the introduction of new compression methods. This addresses a
second issue where log messages generated for an unexpected failure
would not show the compressed segment name involved, which was
confusing, printing instead the name of the non-compressed equivalent.
Reported-by: Georgios Kokolatos
Discussion: https://postgr.es/m/YPDLz2x3o1aX2wRh@paquier.xyz
Backpatch-through: 10
We don't allow to create replication slot_name as an empty string ('') via
SQL API pg_create_logical_replication_slot() but it is allowed to be set
via Alter Subscription command. This will lead to apply worker repeatedly
keep trying to stream data via slot_name '' and the user is not allowed to
create the slot with that name.
Author: Japin Li
Reviewed-By: Ranier Vilela, Amit Kapila
Backpatch-through: 10, where it was introduced
Discussion: https://postgr.es/m/MEYP282MB1669CBD98E721C77CA696499B61A9@MEYP282MB1669.AUSP282.PROD.OUTLOOK.COM
The new test code added in ead9e51e82 is racy -- it hinges on
shared-memory state, which changes before the WARNING message is logged.
Put it the other way around.
Backpatch to 13.
Author: Álvaro Herrera <alvherre@alvh.no-ip.org>
Discussion: https://postgr.es/m/202107161809.zclasccpfcg3@alvherre.pgsql
We had documentation of default_transaction_isolation et al,
but for some reason not of transaction_isolation et al.
AFAICS this is just an ancient oversight, so repair.
Per bug #17077 from Yanliang Lei.
Discussion: https://postgr.es/m/17077-ade8e166a01e1374@postgresql.org
pg_dump failed to preserve the 'enabled' flag (which can be not only
disabled, but also REPLICA or ALWAYS) for partitions which had it
changed from their respective parents. Attempt to handle that by
including a definition for such triggers in the dump, but replace the
standard CREATE TRIGGER line with an ALTER TRIGGER line.
Backpatch to 11, where these triggers can exist. In branches 11 and 12,
pick up a few test lines from commit b9b408c487 to verify that
pg_upgrade is okay with these arrangements.
Co-authored-by: Justin Pryzby <pryzby@telsasoft.com>
Co-authored-by: Álvaro Herrera <alvherre@alvh.no-ip.org>
Discussion: https://postgr.es/m/20200930223450.GA14848@telsasoft.com
When triggers are cloned from partitioned tables to their partitions,
the 'tgenabled' flag (origin/replica/always/disable) was not propagated.
Make it so that the flag on the trigger on partition is initially set to
the same value as on the partitioned table.
Add a test case to verify the behavior.
Backpatch to 11, where this appeared in commit 86f575948c.
Author: Álvaro Herrera <alvherre@alvh.no-ip.org>
Reported-by: Justin Pryzby <pryzby@telsasoft.com>
Discussion: https://postgr.es/m/20200930223450.GA14848@telsasoft.com
When some slots are invalidated due to the max_slot_wal_keep_size limit,
the old segment horizon should move forward to stay within the limit.
However, in commit c655077639 we forgot to call KeepLogSeg again to
recompute the horizon after invalidating replication slots. In cases
where other slots remained, the limits would be recomputed eventually
for other reasons, but if all slots were invalidated, the limits would
not move at all afterwards. Repair.
Backpatch to 13 where the feature was introduced.
Author: Kyotaro Horiguchi <horikyota.ntt@gmail.com>
Reported-by: Marcin Krupowicz <mk@071.ovh>
Discussion: https://postgr.es/m/17103-004130e8f27782c9@postgresql.org
Autoconf's AC_CHECK_DECLS() always defines HAVE_DECL_whatever
as 1 or 0, but some of the entries in msvc/Solution.pm showed
such symbols as "undef" instead of 0. Fix that for consistency.
There's no live bug in current usages AFAICS, but it's not hard
to imagine one creeping in if more-complex #if tests get added.
Back-patch to v13, which is as far back as Solution.pm contains
this data. The inconsistency still exists in the manually-filled
pg_config_ext.h.win32 files of older branches; but as long as the
problem is only latent, it doesn't seem worth the trouble to
clean things up there.
Discussion: https://postgr.es/m/3185430.1626133592@sss.pgh.pa.us
Some commands of ALTER TABLE could fail with the following error:
ERROR: "tab" is of the wrong type
This error is unexpected, as all the code paths leading to
ATWrongRelkindError() should use a supported set of relkinds to generate
correct error messages. This commit closes the gap with such mistakes,
by adding all the missing relkind combinations. Tests are added to
check all the problems found. Note that some combinations are not used,
but these are left around as it could have an impact on applications
relying on this code.
2ed532e has done a much larger refactoring on HEAD to make such error
messages easier to manage in the long-term, so nothing is needed there.
Author: Kyotaro Horiguchi
Reviewed-by: Peter Eisentraut, Ahsan Hadi, Michael Paquier
Discussion: https://postgr.es/m/20210216.181415.368926598204753659.horikyota.ntt@gmail.com
Backpatch-through: 11
41469253e went to the trouble of removing a theoretical bug from
free_sort_tuple by checking if the tuple was NULL before freeing it. Let's
make this a little more robust by also setting the tuple to NULL so that
should we be called again we won't end up doing a pfree on the already
pfree'd tuple. Per advice from Tom Lane.
Discussion: https://postgr.es/m/3188192.1626136953@sss.pgh.pa.us
Backpatch-through: 9.6, same as 41469253e
This fixes a theoretical bug in tuplesort.c which, if a bounded sort was
used in combination with a byval Datum sort (tuplesort_begin_datum), when
switching the sort to a bounded heap in make_bounded_heap(), we'd call
free_sort_tuple(). The problem was that when sorting Datums of a byval
type, the tuple is NULL and free_sort_tuple() would free the memory for it
regardless of that. This would result in a crash.
Here we fix that simply by adding a check to see if the tuple is NULL
before trying to disassociate and free any memory belonging to it.
The reason this bug is only theoretical is that nowhere in the current
code base do we do tuplesort_set_bound() when performing a Datum sort.
However, let's backpatch a fix for this as if any extension uses the code
in this way then it's likely to cause problems.
Author: Ronan Dunklau
Discussion: https://postgr.es/m/CAApHDvpdoqNC5FjDb3KUTSMs5dg6f+XxH4Bg_dVcLi8UYAG3EQ@mail.gmail.com
Backpatch-through: 9.6, oldest supported version
This should have been removed in commit 7e30c186da, which split the loop
into two. Only the first loop uses the 'from' variable; updating it in
the second loop is bogus. It was never read after the first loop, so this
was harmless and surely optimized away by the compiler, but let's be tidy.
Backpatch to all supported versions.
Author: Ranier Vilela
Discussion: https://www.postgresql.org/message-id/CAEudQAoWq%2BAL3BnELHu7gms2GN07k-np6yLbukGaxJ1vY-zeiQ%40mail.gmail.com
Although we were careful to lock the object being added or dropped,
we failed to get any sort of lock on the extension itself. This
allowed the ALTER to proceed in parallel with a DROP EXTENSION,
which is problematic for a couple of reasons. If both commands
succeeded we'd be left with a dangling link in pg_depend, which
would cause problems later. Also, if the ALTER failed for some
reason, it might try to print the extension's name, and that could
result in a crash or (in older branches) a silly error message
complaining about extension "(null)".
Per bug #17098 from Alexander Lakhin. Back-patch to all
supported branches.
Discussion: https://postgr.es/m/17098-b960f3616c861f83@postgresql.org
If an error occurred in the wrong place, it was possible to leave an
unintialized entry in the hash table, leading to a crash. Fixed.
Also, be more careful about the order of operations so that an
allocation error doesn't leak memory in CacheMemoryContext or
unnecessarily advance NextRecordTypmod.
Backpatch through version 11. Earlier versions (prior to 35ea75632a)
do not exhibit the problem, because an uninitialized hash entry
contains a valid empty list.
Author: Sait Talha Nisanci <Sait.Nisanci@microsoft.com>
Reviewed-by: Andres Freund
Discussion: https://postgr.es/m/HE1PR8303MB009069D476225B9A9E194B8891779@HE1PR8303MB0090.EURPRD83.prod.outlook.com
Backpatch-through: 11
Sigh ... I was expecting AC_CHECK_LIB to do something it didn't,
namely update LIBS. This led to not finding ldap_initialize.
Fix by moving the probe for ldap_initialize. In some sense this
is more correct anyway, since (at least for now) we care about
whether ldap_initialize exists in libldap not libldap_r.
Per buildfarm member elver and local testing.
Discussion: https://postgr.es/m/17083-a19190d9591946a7@postgresql.org
This fixes an overflow error when using the numeric * operator if the
result has more than 16383 digits after the decimal point by rounding
the result. Overflow errors should only occur if the result has too
many digits *before* the decimal point.
Discussion: https://postgr.es/m/CAEZATCUmeFWCrq2dNzZpRj5+6LfN85jYiDoqm+ucSXhb9U2TbA@mail.gmail.com
I incorrectly diagnosed the reason why hoverfly is unhappy.
Looking closer, it appears that it fails to link libldap
unless libssl is also present; so the problem was my
idea of clearing LIBS before making the check. Revert
to essentially the original coding, except that instead
of failing when libldap_r isn't there, use libldap.
Per buildfarm member hoverfly.
Discussion: https://postgr.es/m/17083-a19190d9591946a7@postgresql.org
In commit d0a02bdb8, I'd supposed that uniformly probing for
ldap_bind would make the intent clearer. However, that seems
not to work on AIX, for obscure reasons (maybe it's a macro
there?). Revert to the former behavior of probing
ldap_simple_bind for thread-safe cases and ldap_bind otherwise.
Per buildfarm member hoverfly.
Discussion: https://postgr.es/m/17083-a19190d9591946a7@postgresql.org
Commit 7266d0997 added code to pull up simple constant function
results, converting the RTE_FUNCTION RTE to a dummy RTE_RESULT
RTE since it no longer need be scanned. But I forgot to clear
the LATERAL flag if the RTE has it set. If the function reduced
to a constant, it surely contains no lateral references so this
simplification is logically OK. It's needed because various other
places will Assert that RESULT RTEs aren't LATERAL.
Per bug #17097 from Yaoguang Chen. Back-patch to v13 where the
faulty code came in.
Discussion: https://postgr.es/m/17097-3372ef9f798fc94f@postgresql.org
The separate libldap_r is gone and libldap itself is now always
thread-safe. Unfortunately there seems no easy way to tell by
inspection whether libldap is thread-safe, so we have to take
it on faith that libldap is thread-safe if there's no libldap_r.
That should be okay, as it appears that libldap_r was a standard
part of the installation going back at least 20 years.
Report and patch by Adrian Ho. Back-patch to all supported
branches, since people might try to build any of them with
a newer OpenLDAP.
Discussion: https://postgr.es/m/17083-a19190d9591946a7@postgresql.org
Since the executor can't cope with a utility statement appearing
as a node of a plan tree, we can't support cases where a rewrite
rule inserts a NOTIFY into an INSERT/UPDATE/DELETE command appearing
in a WITH clause of a larger query. (One can imagine ways around
that, but it'd be a new feature not a bug fix, and so far there's
been no demand for it.) RewriteQuery checked for this, but it
missed the case where the DML command rewrites to *only* a NOTIFY.
That'd lead to crashes later on in planning. Add the missed check,
and improve the level of testing of this area.
Per bug #17094 from Yaoguang Chen. It's been busted since WITH
was introduced, so back-patch to all supported branches.
Discussion: https://postgr.es/m/17094-bf15dff55eaf2e28@postgresql.org
Due to how pg_size_pretty(bigint) was implemented, it's possible that when
given a negative number of bytes that the returning value would not match
the equivalent positive return value when given the equivalent positive
number of bytes. This was due to two separate issues.
1. The function used bit shifting to convert the number of bytes into
larger units. The rounding performed by bit shifting is not the same as
dividing. For example -3 >> 1 = -2, but -3 / 2 = -1. These two
operations are only equivalent with positive numbers.
2. The half_rounded() macro rounded towards positive infinity. This meant
that negative numbers rounded towards zero and positive numbers rounded
away from zero.
Here we fix#1 by dividing the values instead of bit shifting. We fix#2
by adjusting the half_rounded macro always to round away from zero.
Additionally, adjust the pg_size_pretty(numeric) function to be more
explicit that it's using division rather than bit shifting. A casual
observer might have believed bit shifting was used due to a static
function being named numeric_shift_right. However, that function was
calculating the divisor from the number of bits and performed division.
Here we make that more clear. This change is just cosmetic and does not
affect the return value of the numeric version of the function.
Here we also add a set of regression tests both versions of
pg_size_pretty() which test the values directly before and after the
function switches to the next unit.
This bug was introduced in 8a1fab36a. Prior to that negative values were
always displayed in bytes.
Author: Dean Rasheed, David Rowley
Discussion: https://postgr.es/m/CAEZATCXnNW4HsmZnxhfezR5FuiGgp+mkY4AzcL5eRGO4fuadWg@mail.gmail.com
Backpatch-through: 9.6, where the bug was introduced.
This commit fixes wrong wording like "a fewer kinds"
in the description about track_planning option.
Back-patch to v13 where pg_stat_statements.track_planning was added.
Author: Justin Pryzby
Reviewed-by: Julien Rouhaud, Fujii Masao
Discussion: https://postgr.es/m/20210418233615.GB7256@telsasoft.com
As in 50371df26, this is a bad idea since the callback can't really
know what error is being thrown and thus whether or not it is safe
to attempt catalog accesses. Rather than pushing said accesses into
the mainline code where they'd usually be a waste of cycles, we can
look at the query's rangetable instead.
This change does mean that we'll be printing query aliases (if any
were used) rather than the table or column's true name. But that
doesn't seem like a bad thing: it's certainly a more useful definition
in self-join cases, for instance. In any case, it seems unlikely that
any applications would be depending on this detail, so it seems safe
to change.
Patch by me. Original complaint by Andres Freund; Bharath Rupireddy
noted the connection to conversion_error_callback.
Discussion: https://postgr.es/m/20210106020229.ne5xnuu6wlondjpe@alap3.anarazel.de
Commit 03ffc4d6d added logic to bypass all caching behavior in
LookupOpclassInfo when CLOBBER_CACHE_ALWAYS is enabled. It doesn't
look like I stopped to think much about what that would cost, but
recent investigation shows that the cost is enormous: it roughly
doubles the time needed for cache-clobber test runs.
There does seem to be value in this behavior when trying to test
the opclass-cache loading logic itself, but for other purposes the
cost is excessive. Hence, let's back off to doing this only when
debug_invalidate_system_caches_always is at least 3; or in older
branches, when CLOBBER_CACHE_RECURSIVELY is defined.
While here, clean up some other minor issues in LookupOpclassInfo.
Re-order the code so we aren't left with broken cache entries (leading
to later core dumps) in the unlikely case that we suffer OOM while
trying to allocate space for a new entry. (That seems to be my
oversight in 03ffc4d6d.) Also, in >= v13, stop allocating one array
entry too many. That's evidently left over from sloppy reversion in
851b14b0c.
Back-patch to all supported branches, mainly to reduce the runtime
of cache-clobbering buildfarm animals.
Discussion: https://postgr.es/m/1370856.1625428625@sss.pgh.pa.us